Solar 2-PRO User manual

USER MANUAL
******The led light source is non-user replaceable******
1. Set lighting mode FIRST, THEN set lighting times as (4h, 6h or 12 hours), otherwise, time will not be activated.
2. Motion sensor will be not functional when you set the different brightness level (25%, 50%, 75% or 100%) .
3. The two motion sensor programs are default set and cannot be changed. but the lighting time can be changed as 4H 6H and 12H
4. The light will blink twice when it receives the signal successfully from the remote.
Match operation is to link the light and
remote into one same group, this
allows you to use one remote to control
multi solar lights without interfering
same floodlights within a short
distance.
The remote will control the solar flood
light if you do not do match operation.
What is “match”?
Press and hold the button
MATCH , be ready to pair
the light and remote
Press the light button ON.
and then the light will
blink once. then matching
PROBLEM POSITION HOW TO SOLVE
Light is off
Short working time
Switch is off
No direct sun
Much cloudy or rainy days
Push on the switch
Move light to sunshine place
Work again when sun comes
Debris on solar panel
Installation location
Cloudy or very rainy
Adjust location
Clean solar panel
Work again when sun comes
Battery life is expried
Remote setting is wrong
Replace the battery in remote
Press the longer time button. 2-PRO 4-PRO 6-PRO/8-PRO
MADE IN CHINA
Materials in Package
01 : Solar flood light ( 1pc ) 02 : Solar Panel ( 1pc ) 03 : Remote control ( 1pc ) 04 : Expansion screw ( 4pcs )
05 : 4.5m Adaptor cable (1pc) 06 : 2 Brackets + 4 M4*10 screws07 : AAA Battery ( 2pcs ) 08 : User manual ( 1pc )
REMARK
COMMON TROUBLESHOOT
BEFORE USE
1 2

We recommend you always try to install this solar floodlight a place where the solar panel is exposed to direct sunlight in order to
achieve maximum performance. The working time of the solar flood light is directly related to the solar panel's exposure to sunlight.
The performance will be affected by weather and season. Under manual mode, this light can also work in the day time when the
solar panel is charging the light. This function is designed to provide lighting to the places where there is never daylight, like
warehouses, wine caves etc. Please do not forget to clear the solar panel after a while when it gets dirty.
Model
Luminous flux
Battery capacity
MONO solar panel
Remote control
Motion sensor
Connection cable
2-Pro
>880lm
6.4V 38.4WH
10V 12W
2.4G
Microwave
5 meters totally from luminaire to solar panel
4-Pro
>1,680lm
6.4V 76.8WH
10V 25W
6-Pro
>2,480lm
6.4V 115WH
10V 35W
8-Pro
>3,280lm
6.4V 154WH
10V 50W
1. Measure the holes from the
light bracket and make two marks
to drill.
2. Drill 2 holes with an M10 drill
bit on the surface according to the
two marks.
3. Place the expansion screw into
the hole.
6. Place the light bracket over the
fixings, replace washers.
5. Place the light bracket over the
fixings.
4. Remove the shrapnel, washer,
and the nut from screws.
7. Tighten the two nuts with
wrench.
8. Install the flood light and adjust
the light direction as needed.
Tighten the fixings.
9. Fix the L shape bracket to solar
panel by M4 screws ( 4 screws
totally)
12. Match the light and remote
and use remote to set the lighting
performance as you require.
11. Connect the adapter cable
between the solar floodlight and
the solar panel. Insure that this
waterproof connection is secured
10. Install the solar panels in the
location, and make sure solar
panel is exposed to full sunlight.
Turn ON/OFF manually, functional both for day and night.
Set to turn ON at dusk , Turn off at dawn automatically.
Set 4 different levels of brightness
Test mode. Light will turn ON and operate for 1min and turn OFF
Set light to operate at 100% power when microwave sensor is triggered.
Set light to operate at 100% from 30% output when microwave sensor is triggered.
Set the light to operate lighting time.
REMOTE CONTROL BATTERY INDICATOR
MAIN SPECIFICATION
BEFORE INSTALLATION
The remote control is used to adjust the lighting power and time as you require, in
the summertime or your local sunshine is great all the year-round, then you can
use with 75% or 100% power, otherwise, you can use 50% even 25% power to
save energy of the battery, Also you can set the working time which can be last 4
hours, 6 hours 12 hours, etc. Meanwhile, the motion detection functions are
available which you can use it as a security light. Function 1 is light will be off and
only turn on with 100% power and last 1min when it detects movement, function 2
is light work with 100% power when there is detection from working with 30%
power when no detection.
Different from PIR remote, this is a 2.4G remote that is more sensitive and has no
need to point at the light when you use it, the distance from the remote to the light
can be up to 10 meters in an open-air area.
Red : 0% ~ 30%
Yellow : 31% ~ 70%
Green : 71% ~ 100%
Default Lighting Program : 3 hours 100% + 4 hours 50% + 5 hours 30% for 12 hours operation without motion sensor.
4 meters adapter cable