Solena Mini Par 12 User manual

Mini Par 12
12*1W RGBW Indoor LED Par Light
User's Manual
ATTENTION: Read this manual before using. Do not attempt to open the housing or repair
this device by yourself without contact us!

General Instructions
Unpacking:
Thank you for purchasing this product. Please read user guide for safety and operations information before
using the product. Keep this manual for future reference. This product can create perfect light programs and
effects since it has passed a series of strictly tests before delivery. Please check the attachments listed on
the page after opening the carton. Immediately upon receiving a fixture, carefully unpack the box. Check the
box contents to ensure that all parts are present and that they are in good condition. If any part appears
damaged from shipping, or if the box shows signs of mishandling, notify the shipper immediately. In addition,
retain the box and all the packing material for inspection. In any event, save the carton and all packing
material because, in case that you have to return the fixture to the factory, you will have to do so in its
original box, with its original packing.
What is included: 1* Light, 1*Power Cable, 1*User Guide
Safety Notice:
Please read the following notes carefully because they include important safety information about the
installation, usage and maintenance of this product. It is important to read all these notes before starting to
work with this product.
There are no user serviceable parts inside the light. Any reference to servicing this unit you
may find from now on in this User Manual will only apply to properly C we certified
technicians. Do not open the housing or attempt any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for proper installation of
the light.
Keep this manual for future consultation. If you sell the light to another user, make
sure that they also receive this manual.
Avoid direct eye exposure to the light source while the fixture is on. Always disconnect the light from its
power source before servicing. Always connect the light to a grounded circuit to avoid the risk of
electrocution.
Page 1

This product is for indoor use only! Use only in dry locations. Keep this device away from rain and
moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or
metallic objects.
Make sure there are no flammable materials close to the fixture(s) while operating.
Please prevent this light away from electrical shock
When hanging this fixture, always secure it to a fastening device using a safety cable (not
provided).
Always make sure that you are connecting the light to the proper voltage, as per the specifications in
this manual or on the product's sticker. Never connect the light to a dimmer pack. Make sure that the
power cable is not cracked, crimped or damaged. Never disconnect the fixture by pulling or tugging
on the power cable.
The maximum ambient temperature (Ta) is 104 F (40 C). Do not operate the fixture at a
higher temperature. In case of a serious operating problem, stop using this product
immediately!
Use cleaning tissue to remove the dust absorbed on the external lenses periodically to
optimize light output.
Always replace with the exact same type fuse, replacement with anything other than the
specified fuse can cause fire or electric shock and damage your unit, and will void your
manufactures warranty.
Do not remove or break the warranty label, otherwise it void the warranty.
There are no serviceable parts in the LED light. Please have all servicing and adjustments
made by a qualified service engineer.
Don’t throw this product away just as general trash, please dispose of this product following the
abandon electronic product regulation in your country.
To protect the environment, recycle packing material wherever possible.
Page 2

LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration of
this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. It is estimated that a viable lifespan of 40,000 to 50,000 hours will be achieved under
normal operational conditions. If improving on this lifespan expectancy is of a higher priority, place care in
providing for lower operational temperatures. This may include climatic-environmental and the reduction of
verall projection intensity.
on
o
Technical Specificati
(1)Super bright LED light
(2) long life span upto 20000 hours
(3) Many functions can be achieved through DMX control, such as color change, speed control, strobe, LED
brightness, dimmer, etc.
*LED source: 12*1W RGBW LEDs, total power 12W
*Dimming: electronic dimmer 0% 100%
*Beam angle: 25 degrees
*Operation mode: Sound Active, AUTO, DMX, Master/Slave
*DMX channel: 5CH and/or 8CH
*4 digital display
*Interface: 3 pins XLR jack for DMX or Maser-Slave linking
*Voltage: AC90-240V, frequency: 50HZ to 60HZ, 2A
*Power Rate: 12W
*Net Weight: 0.3Kg
*Gross Weight:0.5Kg (inner box)
*inner: 153*137*115(0.0024cbm)
*Outer Box: 568*326*365 (0.068cbm), 24pcs/CTN
Page 3

ppearance Fixture A
1
2
nu, enter, up, down,5. DMX linking XLR IN/OUT,
.Power source
Setting
3
4
5
6
1. LED bulbs, 2. hanging handle, 3. LCD Digital display
4. key menu: me
6
Function &
pattern is controlled by sound, that is, the rhythm of the sound control the effect of the
changing light pattern.
Page 4
Sound Active
The change of the LED

ed externally. It has no light OFF.
n the master mode.
ing).
of the unit to make the unit more or less sensitive in sound active. The panel has LED indicating for sound
ctive.
t controller.
ether via the XLR connector on the rear of the units. For
e master unit to make the unit more or less sensitive in sound active. The panel has LED indicating for
sound active.
Page 5
AUTO
Auto cycles the built-in programs without being controll
Stand-Alone Operation (Sound Active, AUTO mode)
The mode allows a single unit to react to the beat of the music i
1. Install the units in a suitable position (laying or append
2. Set dipswitch to select SoundActive orAUTO mode.
3. Turn on the unit power, the unit begins reset, then the unit begins working.
4. The unit will react to the low frequencies of music via the internal microphone. Adjust the audio sensitivity knob on
the back
a
Master-Slave Operation
This mode will allow you to link up to 32 units together withou
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select Sound Active or AUTO mode. The others must be
set to Slave mode, set dipswitch to select Slave mode.
3. Use standard XLR microphone cable chain your units tog
longer cable runs we suggest a terminator at the last fixture.
Caution: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can
cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity
and to make sure the pins are not grounded or shorted to the shield or each other.
4. Turn on the all units' power, the units begins reset, and then the unit begins working. The slave units will re-act the
same as the master unit.
5. The units will react to the low frequencies of music via the internal microphone.Adjust the audio sensitivity knob on
the back of th

ional standard to control the system. This mode
he XLR connector on the rear of the
ck Reference Char".
s reset, and then the unit begins working.
5. Use DMX console to control your units.
The LED light only accepts the DMX51 ight.
DMX Control Parameter Chart
(1) Channel Function Value Description
Universal DMX Operation (DMX mode)
The system only accepts the DMX512 signal of internat
allows you to use universal DMX-512 console to operate.
1. Install the units in a suitable position (laying or appending).
2. Use standard XLR microphone cable chain your units together via t
units. For longer cable runs we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches, see the "DMX Address Qui
4. Turn on the all units' power, the units begin
DMX Control: 2 signal of international standard to control the l
5 channels
CH1 Red brightness 0-255 Dark to bright
CH2 Green brightness 0-255 Dark to bright
CH3 Blue brightness 0-255 Dark to bright
CH4 White brightness 0-255 Dark to bright
0-63 No strobe
64-223 AUTO strobe, speed from slow to fast
CH5 Strobe/Flashing
224-255 Sound strobe
(2)
nel ntion
8 channels
Chan Functio Value Descrip
CH1 All 0-255 Dark to brightLEDs
brightness
CH2 Red brightness 0-255 Dark to bright
CH3 Green brightness 0-255 Dark to bright
CH4 Blue brightness 0-255 Dark to bright
CH5 White brightness 0-255 Dark to bright
Page 6

Channel Function Value Description
0-31 Color controlled by CH1 to CH5, no all color change
32-95 on CC01—CC16 with 15 colorsStatic color selecti
controlled by CH7
96-143 GonBup—Color change RonGup –RdownGon –
GdownBon --RupBon-- RonBdown
144-191
n, color
RonGup--RdownGon--GonWup--GdownWon--
BupWon--BonWdown--GupBon--GonBdown--
RupGonWup--RonGdownWon--RdownWon--
GupBupWon--GdownBonWdown--RupBon--
RonBdown--RonGupBup--RdownGonBon--
GonBonWup--GonBdownWon--RupGonWon--
RonGonWdown--RonGonBup--RonGdownBon--
RonBonWup--RonBdownWon—RonWdow
AUTO dimming, speed controlled by CH7
192-223 W-
olor AUTO jumping, speed
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RB
GB-RGW-RGBW C
controlled by CH7
CH6 Color change
224-255 RG-RBW-R-BW-G-RW-B-GW-RGB-W-RB-GBW-
GB-RGW-RGBW Color Sound jumping
CH7 speed control
0-255 6 15 kinds of static colors, speed from
slow to fast
Static color
selection and CC01---CC1
0-63 No strobe
64-223 AUTO strobe, speed from slow to fast
CH8 Strobe/Flashing
224-255 Sound strobe
Notes:
(1) Power on the light, LCD displays d001, connect XRL DMX cable, power on DMX controller,
controlled connected, Master/slave
can be set stand alone. One light is Master and other are Slave.
Page 7
then the light will receive the DMX signal if the light and DMX Controller are connected.
(2) Under the d001, several lights are linked. If there is no DMX
lights

LCD Digital Display
MENU: Function mode selection, such as DMX512/Masterslav
on, brightness adjustment e, AUTO strobe, Sound Active Strobe, Constant light
or decrease
nter: confirm and save the selection
LCD Digital Display Chart
Page 8
DOWN/UP: previous or next, increase
E
AuTo AuLL
Au.01
Au.06
r000-r255 r000-r255
S 01 ---S 16
b000-b255
rgbu
g000-g255
b000-b255
u000-u255
u000-u255
S 00 -S 16
S 00-S 16
CoLo CC01-CC15

(1) Color brightness adjustment
P/DOWN for the increase/decrease value 0-255, press ENTER to save the value. Press MENU to the previous
setting.
Page 9
Sod1
Soud
Sod5
d001-d512
d001-d512
SLAu
CH05
Ch
CH08
LCD Digital Operation Details
001----100
SEnS
r000-r255 r000-r255
rgbu
* On the MENU [rgbu], press ENTER to set color selection
*Press UP/DOWN, then press ENTER to set color brightness adjustment. Press MENU to the previous setting
* Press U
b000-b255
g000-g255 g000-g255
b000-b255
u000-g255 u000-g255
S 00-S 16

speed. Value to 00, no strobe; value 01-16, strobe speed is 1HZ-16HZ.
( color Sett
5, it has 14 kinds of static color selections. Press ENTER to save the setting, press
tting.
(3) AUTO mode Setting
7 kinds of AUTO mode. Press ENTER into
16. Increase value for fast speed.
Press ENTER to save the
AuLL Au.01XX---Au.06 all effects, change 30
*Press S00-S16 to set strobe
2) Static ing
* On the MENU [CoLo], press ENTER for color setting
* Press UP/DOWN, value 01-1
CC01-CC15CoLo
MENU to the previous se
AuLL
AuTo
* Under [AuTo], press ENTER into AUTO mode
* Press UP/DOWN to select AuLL A01.XX---A06.XX（XX:01--06)
AUTO running speed S01-S16 setting. Press MENU to the main manu.
*On the running speed setting, press UP/DOWN to set 15 kinds of speed level 01—
speed level. Press MENU to AUTO running speed mode.
AUTO running
seconds/time
Au.01 R-G-B-W 4 color AUTO jumping, speed from 01--S16
Au.02 G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-R-BW-
RGW
-RGBW 15 color AUTO jumping, speed from 01--S16
Au.03 wnGon--GonBup--GdownBon--RupBon—RonGup--Rdo RonBdown
7 colors dimming, speed from 01--S16
Au.04
on--
up--
pBup--
--
onGonBup--
nWdown Color AUTO dimming,
RonGup--RdownGon--GonWup--GdownWon--BupW
BonWdown-- GupBon--GonBdown--RupGonW
RonGdownWon--RdownWon-- GupBupWon--
GdownBonWdown--RupBon--RonBdown--RonGu
RdownGonBon--GonBonWup--GonBdownWon
RupGonWon-- RonGonWdown--R
RonGdownBon--RonBonWup—
RonBdownWon—Ro
speed from 01--S16
Au.05 TO color
R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-
RGW-RGBW AUTO change, AUTO strobe, AU
change speed 10S, strobe speed from S01-S16
Au.06 RGBW all on and strobe, speed from S01-S16
Page 10
Au.01
Au.06
S 01-----S 16

(4) SOUND mode Set
1---Sod3) 3 kinds of Sound running modes. Press ENTER to save the selection. Press
* Digital dis UND running effects. 1 minute each time
ting
* Under [Soud]，press ENTER into SOUND running mode
* Press UP/DOWN to select (Sod
MENU to the previos selection.
play function details:
Sod1 Includes Sod2---Sod3 All SO
Sod2 R-G-B-W SOUND jumping
Sod3 R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW-RGBW 15colors SOUND jumping
Sod4 R-BW-G-RW-B-GW-RGB-W-RB-GBW-RG-RBW-GB-RGW-RGBW
15colors Sound color change strobe
Sod5 RGBW ALL LED sound strobe
(5) DMX mode Setting
eceived normally, it will display d.xxx (xxx: means DMX address)
(6) Master/Slave mode Setting
to Slave mode. Once Master unit links with Slave unit in good
LAu.
(7) DMX Channel Setting
Page 11
* Under [dxxx]，(xxx:001--512）press ENTER into DMX512 setting mode
* Under DMX512 setting mode, press UP/DOWN to increase or decrease the address 001---512,
then press ENTER to save the setting. Press MENU to the previous setting.
* Once DMX512 signal can be r
* Under [SLAu]，press ENTER in
condition, LCD displays S
Ch CH05
Sod1
Soud
Sod3
d001-d512 d001-d512
SLAu
CH08

annel CH06 or CH24，press ENTER to save the selection. Press MENU to the previous
to increase/decrease sensitivity value 001—100, press ENTER to save the setting. Value increase,
sensitivity higher
* Under [CH]，press ENTER into DMX512 channel setting.
* Press UP/DOWN to select ch
setting.
(8) Sound sensitivity setting
*Under [SEnS], press ENTER into Sound sensitivity setting
*Press UP/DOWN
Troubleshooting
1. If the power supply indicator doesn't light up and the light doesn't work, please check the power supply, the input
f the power supply indicator is light up and sound active indicator isn't light up, but the
d active, please increase the music volume or increase
e.
in slave mode.
.
. Make sure to take a good quality power cable and connection.
Warranty.
difications on the device or unauthorized operation by unqualified persons are not
ntee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns electric shock,
tc.
After trying the above solution you still have a problem, please contact your dealer or our company for service.
Page 12
voltage and the fuse.
2. In Stand-Alone operation, i
light is shut off doesn't work.
A. Because sound is too small make for light shut off in soun
audio sensitivity with sensitivity knob, please check as below.
B. Please check if unit has been set up in slave mode, then set up in master mod
3. In Master-Slave operation, slave unit don't function, please check as below.
A. Make sure to there's only one master in the chain, and the others are set
B. Make sure to control the unit without DMX console controlling
C
Warranty Warnings:
1. Damages caused by the disregard of this user manual are not subject to
The dealer will not accept liability for any resulting defects or problems.
2. Please consider that unauthorized modifications on the device are forbidden due to safety reasons. Please note that
damages caused by manual mo
subject to warranty.
3. If this device will be operated in any way different to the one described in this manual, it may suffer damages and the
guara
e