Solux SX-BS-0685 User manual

Note: 1. See user manuals for more information. 2. For better readability, please print this document with laser printer. 3. Version: SX-BS-0685_QG_EN_V1.4.
Cordless Scanner Quick Guide
Notice
A standard kit contains: a handheld unit, a cradle, a cable, and a quick guide.
It is suggested to read the user manual in details before use.
Parts of the scanner
①Scan window ②Trigger (Press to triggr / Long press 3 seconds to turn on)
③Beeper ④On Base indicator (Blue LED) ⑤Successful decoding indicator (Green LED) /
Communication fail indicator (Red LED) / Charging (Red/Greed LED)
Parts of the cradle
⑥Power indicator (Blue LED)
⑦Communication indicator (Green LED)
⑧Key (Long press 10 seconds to restore factory default setting of
cradle)
Installation of cradle
1. Switch off power of the host. Refer to the below pictures, connect the host with the scanner with different
cables firstly, and then connect the adaptor to the power socket.
2. Ensure that all connections are secure. Switch on the power of the host. After a few seconds, if only the
blue LED on the cradle is ON, it indicates the cradle is in normal working mode.
USB cable RS232 cable
Charge battery 1. Please charge the battery before the first time use. The charge
indicator (Red LED) on the scanner is turned on when the charging is
in progress. When the charging process completes, the charge
indicator (Red LED) is turned off, and the Green LED is turned on.
2. Charging time: 4 hours for fully charged.
3. You can charge the battery via a USB port on the device or an optional
5 VDC adapter. (The 5V power adapter is an optional accessory)
Indication of scanner for wireless data transmission
Successful
Transmission Beeper Red LED Vibration
Yes Off Off Off
No Two long beeps Blinks 2 times, and then
turns off Short vibrates 2 times, and
then turns off
Programming instruction and example
Two programming modes have been provided as bellows:
Sin
g
le-scan settin
g
Scan the related
Single-scan setting Example: To set Flow control to be XON/XOFF.
Multiple-scan settin
g
Scan “SETUP”
Scan “Option barcode”
Scan “the 1st character of option”
Scan “the 2nd character of option”
Scan “END”Example: To set Flow control to be XON/XOFF.

Note: 1. See user manuals for more information. 2. For better readability, please print this document with laser printer. 3. Version: SX-BS-0685_QG_EN_V1.4.
Pair the scanner with cradle
1. Make sure that both the scanner and the cradle are in normal working mode. You can see only the blue
LED on the scanner and the blue LED on cradle are ON.
2. Use the scanner to scan the MAC address at the bottom of the cradle. At the same time, the scanner will
make a beep-beep-beep sound.
3. Once the connection is done, the scanner can be used directly. If the attempt of connection fails, the
scannerl will make a beep-beep sound, and the red LED on the scanner will blinks 2 times, and then turns off.
4. If you want to disconnect, you can scan the barcode below:
Initialization settings and information display
Note:
If you want to turn off the scanner via trigger key, please press and hold the trigger key, after the laser
beam turns off, wait for another 5 seconds, at the same time, the scanner will make a beep sound. The
scanner will be turned off, then you can release the trigger key at this moment.
If you want to turn on the scanner again, please keep the trigger key being pressing for 3 seconds.
Quick setting
1. Scanning mode
Momentary (default) Auto-detection (Good read on) Auto-detection (Good read off)
2. Inter-character delay
5ms (default) 40ms
3. Add suffix
Enter (default) Tab
4. Vibration indication
Enable (default) Disable
5. Beeper indication
Enable (default) Disable
6. Volume of beeper
High (default) Middle Low
Reset parameters of scanner Reset parameters of cradle
Scanner firmware version display Cradle firmware version display
Turn off scanner Note