SOMNI SOMNImask User manual

1
SOMNImask®
Instructions for use
Somni mask is the easiest
way to lucid dreaming

2
TABLE OF
CONTENTS
Disclaimer_______________p.3
Safety precautions________p.4
First launch______________p.5
Settings_________________p.8

3
DISCLAIMER
SOMNImask® is not a method of mind intrusion
and is not associated with mind-altering substances,
hypnotic influences, or any other methods of direct
influence on human consciousness. It is simply a tool
to help you achieve lucid dreaming under certain conditions.
The technique of lucid dreaming requires training and
understanding, and we just give you the opportunity to
achieve better results with less or minimal effort.
So, let’s begin to create your dream.

4
SAFETY
precautions
We strongly reccomend you to use the headphones from
the package contents, cause too long wires can cause
suffocation in your sleep. The Li-Po battery is completely
safe and can be used near the head and organs without the
risk of exposure to radiation. To extend the battery life, try
not to allow the discharge level below 40%.
Thank you for your attention.

5
FIRST LAUNCH
SOMNI
button
In order to turn on SOMNImask® you need to
hold down the device button for two seconds
After that, the indication of the remaining
battery will begin
Recommendations can be read here: https://somni.org/howitworks
When the device is working, press the button for more than 2 seconds,
and the device will go into off mode. Before that, it will show the
remaining battery charge.
The battery charge is shown based on the LED color when
the device is turned on or off.
- Green means full battery power remaining.
- Yellow means half the remaining battery charge.
- Red means low battery.

6
You can connect headphones to the device. In order, to connect
headphones, you need to insert the headphone jack into the input
of the device. Audio input can be seen on the picture
There is only one button for
the device and it’s located on
the top of the device. With the
button you can turn the device
on or off and also test the
audible light signals.
SOMNI
button
audio input
jack 3.5mm
There are no speakers built into the device. In order to hear audio
files that are in the device’s memory. You need to connect headphones
to the audio input. Only audio files: Calm.mp3, Lucid.mp3, Alarm.mp3
can be played through the headphones.
Remember, one earbud is shorter than the other.
Put on a short ear piece that is closer to your
side of the ear

7
eye device
An eye device is positioned in the eye socket of the mask to record eye
movement. Eye sensors are located in the device window.
The mask completely blocks out the light inside for effective tracking
of eye movement. The device has an accelerometer sensor for head
tracking. In order, for the sensors to record eye movement, you need
to wear the eye mask tightly.
Once you have plugged in the headphones, put on
the mask and you are ready for bed.
Firstly, the mask will play a calm melody and then
go into sleep mode so as not to disturb you during
deep sleep phases
After the Calm pause time, eye tracking will begin
to recognize for REM sleep.
If REM sleep has been detected, the device will
turn on Lucid audio and RGB signals. During REM
sleep, you may notice these signals in your dream.

8
SETTINGS
In order to charge or connect the device to a computer, you need to
connect the device and the computer with the USB wire.
Easily insert the connectors as shown on the picture below.
At the bottom of the device is the micro-USB input, this device
input has these functions: charging the device and connect to
a computer or USB-OTG
micro-USB input
SOMNI
After that you can start charging the device or configure it.
To start charging or setting up you need
to hold down the button for 1 second

9
After pressing the button you will see the automatic opening of the main
memory window of the device. It works like a USB flash drive.
The main memory of the device looks like the photo below
The device plays the original audio files: Lucid, Calm, Alarm (mp3 only)
To start configuring the device you need to go to the device config
page at somni.org/program/
After you have gone to the page, you need to click “Upload” button

10
After clicking on the upload
button, a window for selection
will automatically open. Select
“USB Drive” from the list, then
go to the “Configs” folder and
select the “default.txt” file, then
click Open.
After you have opened the default.txt configuration file, you will see
the configuration page. Follow the instructions on the page and
adjust the setings for your convenience.
After setting up, click the “Save settings” button and follow
the instructions below

11
In order to replace the original audio files you need to move your
audio to the main memory of device. For example file “my.mp3”
Then assing this audio in the “default.txt” file. Just go to the Configs
folder and open the “default.txt” file, then rename the old parameter
“fileLucid Lucid.mp3” to “fileLucid my.mp3” and save the file.
Somni Team wish you to cre-
ate a dream that you deserve
Instructions will be updated soon