Sonifex SignalLED Series Instruction Manual

SignalLED
User Handbook
This handbook is for use with the following stock codes:
LD-20F1REC LED Single Flush Mounting 20cm RECORD sign
LD-20F1ONA LED Single Flush Mounting 20cm ON AIR sign
LD-20F1MCL LED Single Flush Mounting 20cm MIC LIVE sign
LD-40F1REC LED Single Flush Mounting 40cm RECORD sign
LD-40F1ONA LED Single Flush Mounting 40cm ON AIR sign
LD-40F1MCL LED Single Flush Mounting 40cm MIC LIVE sign
LD-40F1PHN LED Single Flush Mounting 40cm PHONE sign
LD-40F1TRF LED Single Flush Mounting 40cm TRAFFIC
FLAG sign
LD-40F1ADB LED Single Flush Mounting 40cm AD BREAK sign
LD-40F1REH LED Single Flush Mounting 40cm REHEARSAL sign
LD-40F1DOR LED Single Flush Mounting 40cm DOOR sign
LD-40F1OBT LED Single Flush Mounting 40cm OBIT sign
LD-40F1NOE LED Single Flush Mounting 40cm NO ENTRY sign
LD-40F1EXIT LED Single Flush Mounting 40cm EXIT sign
LD-40F1SIL LED Single Flush Mounting 40cm SILENCE sign
LD-40F1MET LED Single Flush Mounting 40cm MEETING
IN PROGRESS sign
LD-40F1INT LED Single Flush Mounting 40cm
INTERVIEW IN PROGRESS sign
LD-40F2TX-REH Twin Flush Mounting Signs 2x20cm
Twin ‘TX’ & ‘ REH’ sign
LD-40F2ONA-MCL Twin Flush Mounting Signs 2x20cm
Twin ‘ON AIR’ & ‘MIC LIVE’ sign
LD-40F2ONA-SIL Twin Flush Mounting Signs 2x20cm
Twin ‘ON AIR’ & ‘SILENCE’ sign
LD-40E1REC SignalLED double sided end mounting 40cm
RECORD sign
LD-40E1ONA SignalLED double sided end mounting 40cm
ON AIR sign
LD-40E1MCL SignalLED double sided end mounting 40cm
MIC LIVE sign
LD-40E2 SignalLED twin double sided end mounting
2 x 20cm sign
LD-KE1 SignalLED conversion kit, single ush mount
to end mount
LD-KC1 Ceiling Mounting For 40cm Or 20cm Flush
Mounting Signs
LD-IT SignalLED end mount sign installation tool

bSignalLED User Handbook
SIGNALLED STUDIO ILLUMINATED
SIGNS HANDBOOK
SIGNALLED STUDIO ILLUMINATED SIGNS HANDBOOK
This handbook is for use with the following stock codes:
LD-20F1REC LED Single Flush Mounting 20cm RECORD sign
LD-20F1ONA LED Single Flush Mounting 20cm ON AIR sign
LD-20F1MCL LED Single Flush Mounting 20cm MIC LIVE sign
LD-40F1REC LED Single Flush Mounting 40cm RECORD sign
LD-40F1ONA LED Single Flush Mounting 40cm ON AIR sign
LD-40F1MCL LED Single Flush Mounting 40cm MIC LIVE sign
LD-40F1PHN LED Single Flush Mounting 40cm PHONE sign
LD-40F1TRF LED Single Flush Mounting 40cm TRAFFIC FLAG sign
LD-40F1ADB LED Single Flush Mounting 40cm AD BREAK sign
LD-40F1REH LED Single Flush Mounting 40cm REHEARSAL sign
LD-40F1DOR LED Single Flush Mounting 40cm DOOR sign
LD-40F1OBT LED Single Flush Mounting 40cm OBIT sign
LD-40F1NOE LED Single Flush Mounting 40cm NO ENTRY sign
LD-40F1EXIT LED Single Flush Mounting 40cm EXIT sign
LD-40F1SIL LED Single Flush Mounting 40cm SILENCE sign
LD-40F1MET LED Single Flush Mounting 40cm MEETING IN PROGRESS sign
LD-40F1INT LED Single Flush Mounting 40cm INTERVIEW IN PROGRESS sign
LD-40E1MCL SignalLED double sided end mounting 40cm MIC LIVE sign
LD-40E1ONA SignalLED double sided end mounting 40cm ON AIR sign
LD-40E1REC SignalLED double sided end mounting 40cm RECORD sign
LD-40E2 SignalLED twin double sided end mounting 2 x 20cm sign
LD-IT SignalLED end mount sign installation tool
LD-KC1 Ceiling Mounting For 40cm Or 20cm Flush Mounting Signs
LD-KE1 SignalLED conversion kit, single ush mount to end mount
©Sonifex Ltd, 2009 - 2010
All Rights Reserved
Revision 1.07, June 2010
This version combines the LD-F1 and the LD-E1 handbooks.
Sonifex Ltd, 61, Station Road, Irthlingborough,
Northants, NN9 5QE, England.
Tel: [phone]
Fax: [phone]
Email: [email protected].uk
Website: http://www.sonifex.co.uk
Information in this document is subject to change without notice and does not represent a commitment on the part of
the vendor. Sonifex Ltd shall not be liable for any loss or damage whatsoever arising from the use of information or any
error contained in this manual.
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording, information storage and retrieval systems, for any purpose other than the purchaser’s
personal use, without the express written permission of Sonifex Ltd. Unless otherwise noted, all names of companies,
products and persons contained herein are part of a completely ctitious adaptation and are designed solely to
document the use of Sonifex product.

SignalLED User Handbook i
CONTENTS
CONTENTS
i
Warranty Information 1
Introduction 1
Safety Information 1
Handling Notes 1
Power Supply Approval Documents 2
Installation 4
Mounting The Sign 4
Opening The End Covers 4
LD-20F1 & LD-40F1 Flush Sign Mounting Requirements 4
LD-40E1 & LD-40E2 End Mounting Requirements 5
LD-KC1 Ceiling Mounting Kit 5
Connecting The Power and Signal Connections For Flush Mounted Signs 6
Connecting The Power & Signal Connections For End Mounted Signs 7
Power Supply 7
Programming Colour & Illumination Modes 9
Setting The Colour & Display Mode(s) of The Sign 9
1. Select Input Conditions 9
2. Colour 10
2-1. Load Colour Settings 11
3. Setting Which Side (Segment) of Your Sign Illuminates 11
3-1. Load Segment Selection Setting 11
4. Setting the Illumination Mode 12
4.1. Load Illumination Mode Setting 12
Technical Specications 13
Appendix 1 14
LD-KE1 SignalLED Conversion Kit, Single Flush Mount to End Mount 14
Right Hand Side Fitting of the Conversion Kit 14
Left Hand Side Fitting of the Conversion Kit 16
Appendix 2 18
SignalLED Precongurations 18

ii SignalLED User Handbook
FIGURES
FIGURES
Figures
Fig 1-1: Australia Certicate of Approval, (this is a three page document) 2
Fig 1-2: CB Certicate of Approval, (this is a two page document) 2
Fig 1-3: CE Certicate of Approval, (this is a ten page document) 3
Fig 1-4: UL Certicate of Approval, (this is a one page document) 3
Fig 2-1: LD-20F1 & LD-40F1 Flush Sign Mounting Requirements 4
Fig 2-2: LD-40E1 & LD-40E2 End Mounting Requirements 5
Fig 2-3: LD-KC1 Ceiling Mounting Kit 5
Fig 2-4: Cable Routing Cut-Outs 6
Fig 2-5: Opening The Access Door 6
Fig 2-6: Mode Settings & Connection Bloc 6
Fig 2-7: LD-IT End Mount Sign Installation Tool 7
Fig 2-8: Opening The Access Door 7
Fig 2-9: Wire Link For Power Supply 7
Fig 5-1: Sign Components to be Converted 14
Fig 5-2: Kit Components Used for the Conversion 15
Fig 5-3: Removing the Left Hand Assembly 15
Fig 5-4: Removing the Right Hand Flush Wall Moulding 16
Fig 5-5: Right Hand Conversion Re-Assembly 16
Fig 5-6: Left Hand Conversion Re-Assembly 17

SignalLED User Handbook 1
1
WARRANTY & INTRODUCTION
WARRANTY & INTRODUCTION
Warranty Information
This product is supplied with a 12 month back to base warranty. For further details, please
refer to the Sonifex website: http://www.sonifex.co.uk/company/terms/index.shtml
In order to register the date of purchase so that we can keep you informed of any design
improvements or modications, it is important to complete the warranty registration
document that is enclosed and return it to Sonifex Ltd in the UK.
For your own records you should write down the serial number of the SignalLED sign.
Serial Number TL………………………………………
Introduction
The SignalLED Sign is a new elegant approach to illuminated displays and signage. Using
the latest technology and components, the SignalLED sign can be simply congured onsite
for colour and mode.
t $IPPTFGSPNXIJUFHSFFOSFECMVFZFMMPXPSBOHFDZBOBOENBHFOUB
t $IPPTFGSPNBMBSHFSBOHFPGEJòFSFOUTJHOUFYU
t 'PVSJMMVNJOBUJPONPEFTDPOTUBOUøBTIJOHQVMTJOHBOEPò
t 5XPDPOUSPMQVMMMPXJOQVUT
t 4JOHMFPSUXJOTJHOTXJUITFQBSBUFDPOUSPMT
t %$JOQVUQPXFSTVQQMZQSPWJEFE
t 'MVTINPVOUFEUPUIFXBMMPSFOENPVOUFE
t %PVCMFTJEFEFOENPVOUJOHBWBJMBCMFGPSVTFJODPSSJEPST
t 4JNQMFUPJOTUBMM
t $VTUPNTJHOTDBOCFNBEFUPPSEFS
Safety Information
This equipment has been designed to meet the safety regulations currently advised in the
country of purchase and it conforms to the safety regulations specied by use of
the CE Mark. This equipment operates in a horizontal position.
Handling Notes
The SignalLED sign should be installed in an area which is not subject to excessive heat or
cold. Also, you should avoid installing it in atmospheric conditions which are dusty, smoky,
or dirty, or where there is moisture or vibration. The sign is for internal use only. The unit is
not sealed and cannot be used outside or in very damp or humid environments.
Do not use any solvents to clean the sign. Use a soft dry brush or a clean cloth moistened
with water or mild detergent.
Avoid using the SignalLED sign close to strong sources of electromagnetic radiation such as
video monitors or high power electric cabling.
In all cases the SignalLED sign should be installed and serviced by qualied personnel.

2SignalLED User Handbook
1POWER SUPPLY
APPROVAL DOCUMENTS
POWER SUPPLY APPROVAL DOCUMENTS
Power Supply Approval Documents
The power supply used with
the SignalLEDs is UL, EC and CC
approved. For a more detailed view
of the certicates, please check
online at: http://www.sonifex.co.uk/
signalled/index.shtml
Fig 1-1: Australia Certicate of Approval
Fig 1-2: CB Certicate of Approval

SignalLED User Handbook 3
1
POWER SUPPLY APPROVAL DOCUMENTS
POWER SUPPLY
APPROVAL DOCUMENTS
Fig 1-3: CE Certicate of Approval
Fig 1-4: UL Certicate of Approval

4SignalLED User Handbook
2INSTALLATION
INSTALLATION
Installation
Mounting The Sign
Route the signal and power supply cables before nalising the mounting of the sign. These
cables can be routed either through the aperture, or through the cable cut-outs in the back
of the wall mount moulding.
The LED sign should be mounted on a rm solid surface. The sign is supplied with a
mounting kit comprising 2 x wall plugs and 2 x large ange screws.
Note: You’ll need the following tools to mount the sign: an electric drill tted with a 6mm
diameter masonry drill bit, a No.1 Pozi-drive screwdriver and a spirit level.
- Drill 2 holes, approximately 34mm deep, using a 6mm diameter masonry drill at the
pitch shown on the drawings.
- Insert the wall plugs ush with the surface.
- Use a spirit level on the aluminium tube section to set the sign level before fully
tightening.
The screws can also be used for xing into wood. For correct tting drill a small pilot hole
into the wood before tting the screw.
Opening The End Covers
To get access to the sign mounting points, the side covers need to be opened. Use a
No.1 Pozi-drive screwdriver to unscrew the side cover and gently slide the cover forward
approximately 8mm until it reaches the stops. Pivot open the cover. Please note: do not to
use excessive force when opening the cover.
LD-20F1 & LD-40F1 Flush Sign Mounting Requirements
This sign is to be mounted ush to a wall. Minimum clearances from the sign to an adjacent
wall or ceiling are shown below.
Fig 2-1: LD-20F1 & LD-40F1 Flush Sign Mounting Requirements
An absolute minimum of 60mm is required for the opened end cap, a right angled
screwdriver would be needed to screw (unscrew) the end cap retaining screw.
30mm minimum clearance between
ceiling and mounting hole
Minimum clearance
to an adjacent
wall using 2 small
No. 1 Pozi-drive
screwdriver.
Wall Ceiling
30mm
200mm
LD-40F1 520 mm
LD-20F1 316 mm
= Mounting hole

SignalLED User Handbook 5
2
INSTALLATION
INSTALLATION
LD-40E1 & LD-40E2 End Mounting Requirements
To create an attractive invisible-xing nish,
the SignalLED assembly is clipped into a wall
mount plate. The wall mount plate must be
securely tted to a smooth, solid surface before
attempting to t the SignalLED assembly. Drill 2
holes, approximately 34mm deep, using a 6mm
diameter masonry drill, and attach the wall
mount plate (coloured red in the illustration
above) to the wall. At this point, the LD-IT, end-
mount installation tool can be used to hold the
sign in place while you connect the power and
Metal Plate
5mm screw goes here
30mm
25mm
33mm
65mm
140mm
38mm minimum
44mm
Ceiling
= Wall Mounting Plate shown in red
= Wall Mounting Holes
= Hanger Slots
signal cables. The cable retention clips can be used to hold the cables in the sign. See page
4 for information on connecting the Power and Signal cables.
The sign is tted by locating the four internal hanger plate hooks into the four slots
in the wall mount plate. Once located, hold the sign around the end moulding of the
SignalLED assembly (where the door is tted) and press down into its nal position.
The sign retaining pins will clip into the indentations on the side of the wall mount
plate and this should result in a click as the plastic pins move into their nal position.
Note: a reasonable amount of force is needed to fully connect the LED sign assembly to
the wall plate.
LD-KC1 Ceiling Mounting Kit
Open the end covers of the sign. Take the 5mm screw out of each of the
LD-KC1 brackets and use the screws to attach the sign covers to them,
where indicated on the drawing below. Ensure that the sign cover
sits comfortably against the metal plates on each of the bracket.
The LD-KC1 ceiling mounting kit can be used for mounting a 40cm or
20cm ush mounting sign either down from the ceiling
or up from a surface, e.g. table-top
or top of a rack.
81mm
minimum
clearance to
open the
DIPSwitch
cover ap
Fig 2-2: LD-40E1 & LD-40E2 End Mounting
Requirements
Fig 2-3: LD-KC1 Ceiling Mounting Kit

6SignalLED User Handbook
INSTALLATION
INSTALLATION
2
Connecting The Power and Signal Connections For Flush Mounted Signs
To get access to the cable connection block and the mode switches which are on the PCB
inside the sign, the door on the underside of the end plastic moulding must be opened.
To open the door push the clip towards the sign and pull down on the small lip, see Fig 2-5.
Do not attempt to remove the door from the end moulding. Access to the connection block
and the mode switches is possible with the door fully open.
Fig 2-4: Cable Routing Cut-Outs Fig 2-5: Opening The Access Door
Fig 2-6: Mode Settings & Connection Bloc
   
    
   




  
   






 

 

SignalLED User Handbook 7
2
INSTALLATION
INSTALLATION
Connecting The Power & Signal Connections For End Mounted Signs
It is recommended that the LD-IT SignalLED end mount sign installation tool is used to assist
the termination of the power and signal connections. The tool is designed to hold the sign
on the pre-tted wall mount plate leaving both hands free to make the connections, as
shown in Fig. 2-7.
Fig 2-7: LD-IT End Mount Sign Installation Tool
To get access to the cable connection block and the mode switches, which are on the PCB
inside the sign, the door on the underside of the end plastic moulding must be opened.
To open the door push the clip towards the sign and
pull down on the small lip. See Fig 2-8. Do not attempt
to remove the door from the end moulding. Access
to the connection block and the mode switches is
possible with the door fully open.
Fig 2-8: Opening The Access Door
Power Supply
The sign can be connected and powered either with the supplied DC power supply, or
with a regulated DC supply rated 5V to 7V DC, 0.5mA minimum. On the supplied DC power
supply, the +6V is indicated with a dashed white line on one of the cables.
Pin 1 (Signalling Input 1)
Pin 2 (+6V)
Pin 3 (0V)
Pin 4 (Signalling Input 2)
Wire Link
Fig 2-9: Wire Link For Power Supply

8SignalLED User Handbook
INSTALLATION
INSTALLATION
2
The signalling inputs are used to control the sign and are pulled low (to 0V, pin 3) to activate.
Please note pins 3 (0V) and 1 (input 1) are linked by default so that the sign will illuminate in
its default mode when rst powered up.
The power supply 0V is then inserted into pin 3 along with the link and the +6V supply into
pin 2. The positive voltage is normally marked by a white stripe on the relevant wire - test
this with a voltmeter if you are unsure.
If the sign needs to be controlled externally, remove the link and t a switch or other contact
closure. If you wish to use the sign in its alternate mode, remove this link and link pin 4 to
pin 3 instead.
Use a small at blade screwdriver to undo the connection block screw terminals and also to
adjust the mode switches (see following for information on this). Do not fully remove the
screws from the terminals - they only need 2 or 3 full turns to accept the wire ends. Also,
take care not to apply too much force to the connection block when tting the wire ends, as
this could damage the PCB.
When the power and signalling connections have been made and the mode switches set
up, close the access door by pressing the clip back to its original position. It will click into
place when it is fully home.
After all of the terminations have been checked and the cables have been routed through
the cable clamps, close the end cover by reversing the opening procedure, taking care not
to overtighten the retaining screw.

SignalLED User Handbook 9
PROGRAMMING
3
PROGRAMMING
Input State Signalling
Mode SWT2 SWT3
Program resting (when no
signalling inputs active) 10ò 0ò
Signalling Input 1 active 2 On 0ò
Signalling Input 2 active 3 0ò On
Signalling Input 1 & Input
2 active 4OnOn
Now select the colour that you want the sign to show when the input state above is used.
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
Programming Colour & Illumination Modes
Although the SignalLED is delivered as standard to indicate a certain colour when a pull-low
UP7JOQVUTJHOBMJTBQQMJFEUIFTJHOJTQSPHSBNNBCMFUPBMMPXBOVNCFSPGEJòFSFOU
display modes and uses. For example, the sign can be made to switch between 4 colours,
one for each of the input conditions below. The sign can also illuminate a certain colour
when no input signal is connected, i.e. it can be permanently illuminating, or it can be made
to switch from one colour to another on application of an input signal.
Setting The Colour & Display Mode(s) of The Sign
5IFTJHODBOCFTFUUPJMMVNJOBUFJOEJòFSFOUTUBUFTBDDPSEJOHUPUIFDPNCJOBUJPOPG
the 2 x pull-low signalling inputs present at the connector. For each state, the colour, the
illumination mode and the segments to be illuminated can be programmed. To change the
settings for any or all the signalling modes use the following instructions.
1. Select Input Conditions
5IFSFBSFGPVSTUBUFTPGTJHOBMMJOHJOQVUTFBDIPGXIJDINBZIBWFEJòFSFOUEJTQMBZNPEFT
To start the setup procedure select the signalling input state you wish to set as follows:
Set switches 2 and 3 to select the relevant input state, e.g. if you want to use Signalling input
UPDPOUSPMUIFTJHOUIFOTFU485UP0OBOE485UP0ò
1
ON
1
OFF
1
As
Previous

10 SignalLED User Handbook
PROGRAMMING
3
PROGRAMMING
2. Colour
To choose the colour of the sign set the switches as follows:
Colour SWT4 SWT5 SWT6 SWT7 SWT8
0ò On 0ò 0ò 0ò 0ò
Red On On 0ò 0ò 0ò
Green On 0ò On 0ò 0ò
Blue On On On 0ò 0ò
Cyan On 0ò 0ò On 0ò
Magenta On On 0ò On 0ò
Yellow On 0ò On On 0ò
White OnOnOnOn0ò
Orange On 0ò 0ò 0ò On
Brick Red On On 0ò 0ò On
Dual Colour
Mode* On On On On On
*Note: Dual Colour Mode can only be assigned when both inputs are active - it will
illuminate the two halves of the sign according to the colours set for input 1 and input
2 individually.
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
1
ON
1
OFF
1
As
Previous

SignalLED User Handbook 11
3
PROGRAMMING
PROGRAMMING
2-1. Load Colour Settings
Once the DIPSwitches are set in the required state, toggle SW1 (i.e. DIPSwitch SW1 On and
UIFO0ò UPTFUUIFDPMPVS
then
3. Setting Which Side (Segment) of Your Sign Illuminates
'PSDNTJHOTUIFUXPTJEFTPGUIFTJHODBOCFDPOUSPMMFEJOEFQFOEFOUMZJFEJòFSFOU
colours and ashing modes can be controlled on each side.
Side
(Segment) SWT4 SWT5 SWT6 SWT7 SWT8
Master
(section of
the sign
nearest the
connection
block
0ò 0ò 0ò 0ò 0ò
Slave
(section of
the sign
furthest
from the
connection
block)*
0ò 0ò On 0ò 0ò
Whole Sign 0ò 0ò 0ò On 0ò
*Note: The slave segment is not valid for 20cm signs and so, selecting this option with a
DNTJHOXJMMNFBOUIBUUIFTJHOXJMMBQQFBSUPCFTXJUDIFEPò
3-1. Load Segment Selection Setting
Once the DIPSwitches are set in the required state, toggle SW1 (i.e. DIPSwitch 1 On and
UIFO0ò UPTFUUIFTFHNFOUTFMFDUJPO
then
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
1
ON
1
OFF
1
As
Previous

12 SignalLED User Handbook
3PROGRAMMING
PROGRAMMING
4. Setting the Illumination Mode
Illumination
Mode SWT4 SWT5 SWT6 SWT7 SWT8
On
Constantly 0ò On 0ò 0ò 0ò
Flashing
(0.5 sec on,
TFDPò
continuous)
0ò On On 0ò 0ò
Pulsing
YPOPò
in 0.5 sec,
TFDPò
continuous)
0ò On 0ò On 0ò
Alternate
Flash Mode* 0ò On On On 0ò
Follow
Mode* 0ò On On On On
*Note: Alternate Flash & Follow modes can only be assigned when both pull-low inputs are
active, so DIPSwitches 2 & 3 must both be set to On. They will illuminate the two halves of
the sign according to the modes set for input 1 and input 2. These modes are designed for
40cm signs that have segments independently set by signalling modes 2 & 3.
4.1. Load Illumination Mode Setting
Once the DIPSwitches are set in the required state toggle SW1 (ie switch SW1 on and
UIFOPò
then
5. Next Steps
Now repeat steps 1-4 for all remaining input conditions to be changed and then return all
TXJUDIFTUPUIFPòTUBUF
Note: Remember if you’re using both inputs to control the sign, you need to congure the
case when both inputs are active as well as when each individual input is active. Dual Colour
Mode (page 8) may be useful in this application.
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8
1
ON
1
OFF
1
As
Previous
DIPSwitches
1 2 3 4 5 6 7 8
DIPSwitches
1 2 3 4 5 6 7 8

SignalLED User Handbook 13
TECHNICAL SPECIFICATION
4
TECHNICAL SPECIFICATION
Technical Specications
Physical Specication
Power Supply: Plug-top power supply providing 6V at 1A, with 4 international wall
adapters (UK, EU, US and AUS) and 5m lead to bare ends.
Power Input: 5-7V DC
40cm Sign: 500mA max
Input Connector: 4 way screw terminal block
Control Inputs: 2 x pull-down to 0V
Perspex Dimensions: Single: 40cm (W) x 8cm (H)
Overall Sign Dimensions:
LD-20F1 333mm x 129mm x 60mm
LD-40E1 493mm x 149mm x 71mm
LD-40E2 493mm x 149mm x 71mm
LD40-F1 527mm x 129mm x 60mm
LD-40F2 527mm x 129mm x 60mm
Equipment Type
Single Flush Mounting Signs (20cm):
LD-20F1REC 20cm ‘RECORD’ Sign
LD-20F1ONA 20cm ‘ON AIR’ Sign
LD-20F1MCL 20cm ‘MIC LIVE’ Sign
Single Flush Mounting Signs (40cm):
LD-40F1REC 40cm ‘RECORD’ Sign
LD-40F1ONA 40cm ‘ON AIR’ Sign
LD-40F1MCL 40cm ‘MIC LIVE’ Sign
LD-40F1PHN 40cm ‘PHONE’ Sign
LD-40F1TRF 40cm ‘TRAFFIC FLAG ON’Sign
LD-40F1ADB 40cm ‘AD BREAK’ Sign
LD-40F1REH 40cm ‘REHEARSAL’ Sign
LD-40F1DOR 40cm ‘DOOR’ Sign
LD-40F1OBT 40cm ‘OBIT’ Sign
LD-40F1NOE 40cm ‘NO ENTRY’ Sign
LD-40F1EXIT 40cm ‘EXIT’ Sign
LD-40F1SIL 40cm ‘SILENCE PLEASE’ Sign
LD-40F1MET 40cm ‘MEETING IN PROGRESS’ Sign
LD-40F1INT 40cm ‘INTERVIEW IN PROGRESS’ Sign
Twin Flush Mounting Signs (2 x 20cm):
LD-40F2TX-REH 2 x 20cm ‘TX’ & ‘ REH’ Sign
LD-40F2ONA-MCL 2 x 20cm ‘ON AIR’ & ‘MIC LIVE’ Sign
Double Sided End Mounting Signs (40cm):
LD-40E1REC 40cm ‘RECORD’ Sign
LD-40E1ONA 40cm ‘ON AIR’ Sign
LD-40E1MCL 40cm ‘MIC LIVE’ Sign
Mounting Kits:
LD-KE1 End Mounting Kit For 40cm Or 20cm Flush Mounting Signs
LD-IT LED Sign End Mounting Installation Tool
LD-KC1 SignalLED Ceiling or Desk Mount Bracket (Pair)
Weights & Boxed Dimensions:
Sign Type Width (cm) Depth (cm) Height (cm) Gross Weight (cm) Net Weight (kg)
LD-20F1 style signs 39 20 11 1.0 0.65
LD-40E1 style signs 60 20 11 1.1 0.75
LD-40E2 style signs 60 20 11 1.1 0.75
LD-40F1 style signs 60 20 11 1.1 0.75
LD-40F2 style signs 60 20 11 1.1 0.75
Note : Weights are approximate and based on a sign supplied with the PSU.

14 SignalLED User Handbook
APPENDICES
APPENDICES
5
Appendix 1
LD-KE1 SignalLED Conversion Kit, Single Flush Mount to End Mount
To convert the LD-20F & LD-40F style ush mount single sided signs into single sided end
mount signs you will need to t the LD-KE1 conversion kit. Please follow these instructions
carefully.
Note: You’ll need the following tools to use the conversion kit:, a No. 0 and No.1 Pozi-drive
screwdriver.
Take care not to damage the clear surface of the sign board. The surface will be marked by
swarf or rough surfaces, so please use a clean cloth to hold the sign.
Because the sign is single sided the text will only be correctly viewable from one side. If the
UFYUNVTUCFWJFXFEGSPNPOFQBSUJDVMBSTJEFUIJTNVTUCFDIPTFOJOJUJBMMZBTJUXJMMBòFDUUIF
disassembly and subsequent re-assembly of the sign
As standard the SignalLED PCB is tted into the right hand end of the LD-20F & LD-40F
(see Fig 5-1). If you would like the sign to be viewable with the right hand side of the sign
mounted onto the wall please use the‘Right Hand Side’ tting instructions.
If you would like the sign to be viewable with the left hand side of the sign mounted onto
the wall, please use the ‘Left Hand Side’tting instructions.
Fig 5-1: Sign Components to be Converted
Right Hand Side Fitting of the Conversion Kit
1) Open the end cover on the left hand ush mount assembly by removing the self
tapping screw with a No.1 pozi-drive screwdriver.
2) Remove the left hand ush mount assembly by unscrewing the 4 screws that x the
end moulding to the aluminium tube. These are located inside at the bottom of the
end moulding. See Fig 5-3.

SignalLED User Handbook 15
5
APPENDICES
APPENDICES
3) Align the 4 pins of the extrusion end cover with the screw holes in the exposed end
of the aluminium tube. Note the orientation of the cut-out with the clear sign board
and press t the end cover fully onto the aluminium tube.
4) Open the end cover on the right hand ush mount assembly by removing the self-
tapping screw with a No.1 pozi-drive screwdriver.
5) Remove the ush wall mount moulding from the end moulding by unscrewing the 4
screws visible under the cover See Fig 5-4.
6) Fit the internal hanger plate into the end wall mount moulding. Align the semi-
circular cut-out in the hanger plate with the raised section above the serial number
label, which indicates the bottom of the assembly. Also make sure that the hanger
plate ts into the slots in the wall mount moulding.
7) This combination is then xed to the right hand ush mount assembly end moulding
with the 4 supplied No.4 x ¾ self tap screws. See Fig 5-5. Do not substitute any other
screws in these positions and do not reuse the screws removed from these positions,
because they will not support the sign correctly.
8) Please refer to the installation notes for the LD-40E style signs to complete the nal
tting and colour/conguration set-up.
Fig 5-2: Kit Components Used for the Conversion Fig 5-3: Removing the Left Hand Assembly

16 SignalLED User Handbook
5
APPENDICES
APPENDICES
Fig 5-4: Removing the Right Hand Flush Wall Moulding Fig 5-5: Right Hand Conversion Re-Assembly
Left Hand Side Fitting of the Conversion Kit
Note: With this conversion you will be removing the PCB from the sign so full anti-static
precautions must be taken to protect the PCB from damage. Failure to do so may result in
the sign not working and invalidating the warranty.
1) Open the end cover on the right hand ush mount assembly by removing the self-
tapping screw with a No.1 pozi-drive screwdriver.
2) Remove the 2 small screws that hold the PCB into the right hand ush mount
assembly and withdraw the PCB. Place the PCB on an antistatic surface.
3) Remove the right hand ush mount assembly by unscrewing the 4 screws that x the
end moulding to the aluminium tube. These are located inside at the bottom of the
end moulding.
4) Align the 4 pins of the extrusion end cover with the screw holes in the exposed end
of the aluminium tube. Note the orientation of the cut-out with the clear sign board
and press t the end cover fully onto the aluminium tube.
5) Open the end cover on the left hand ush mount assembly by removing the self-
tapping screw with a No.1 pozi-drive screwdriver.
6) Remove the ush wall mount moulding from the end moulding by unscrewing the
4 screws visible under the cover.
7) Replace the PCB into the left hand end moulding aligning the PCB edge with the
guide tracks in the aluminium extrusion. Ret the 2 small screws that hold the PCB,
taking care not to over tighten and strip the plastic.
8) Fit the internal hanger plate into the end wall mount moulding. Align the semi-
circular cut-out in the hanger plate with the raised section above the serial number
label, which indicates the bottom of the assembly. Also make sure that the hanger
plate ts into the slots in the wall mount moulding.