Sonoma Goods for Life Cantilever LED Solar Umbrella User manual

PART LIST QUANTITY
A 1 PC
B 1 PC
C 1 PC
D 1 PC
E 4 PC
F 4 PC
G 1 PC
H1PC
I16PC
J4PC
K4PC
L 1 PC
LOWER POLE
CROSS BASE TOP BAR
BOLT
ASSEMBLE ON A FLAT, PROTECTED SURFACE
BASE BOTTOM
SOLAR PANEL
PLASTIC FUNNEL
BASE TOP
WASHER
WRENCH
SAVE THESE INSTRUCTIONS
FIGURE
DESCRIPTION
UMBRELLA FRAME
SONOMA OFFSET SOLAR UMBRELLA ASSEMBLY INSTRUCTIONS
CROSS BASE BOTTOM BAR
PLASTIC WING NUT
FOR MISSING OR INCORRECT PARTS/HARDWARE, CONTACT THE MANUFACTURER'S CUSTOMER SERVICE DIRECTLY AT
[phone]
REFER TO LAST PAGE FOR ADDITIONAL CUSTOMER SERVICE DETAILS.
Page 1/4

STEP 1
A. ON A FLAT PROTECTED SURFACE PLACE CROSS
BASE BOTTOM BAR (D). PLACE CROSS BASE TOP
BAR (C) INTO CROSS BASE BOTTOM BAR (D) BY
ALIGNING THE CENTER NOTCH.
B. PLACE LOWER POLE (B) ONTO CROSS BASE.
ALIGN THE BOLT HOLES IN BASE (C&D) AND LOWER
POLE (B). SECURE LOWER POLE (B) USING BOLTS (J)
AND WASHERS (K). TIGHTEN COMPLETELY USING
WRENCH (L).
ASSEMBLY INSTRUCTIONS (CONTINUED)
SONOMA OFFSET SOLAR UMBRELLA ASSEMBLY INSTRUCTIONS
STEP 2
A. PLACE BASE BOTTOM (F) ONTO THE CROSS AS
SHOWN. TAKE A SECOND BASE BOTTOM (F) AND
PLACE ONTO CROSS BASE. CONNECT THE LEDGES
AND GROOVES OF THE BASES. REPEAT FOR OTHER
TWO BASE BOTTOMS (F).
B. FILL TANKS COMPLETELY WITH WET SAND.
C. TAKE TWO BASE TOP (E) PIECES AND TURN
UPSIDE DOWN ON A FLAT PROTECTED SURFACE.
INSERT THE PLASTIC WING NUT (I) ON ONE BASE
TOP (E) THROUGH THE HOLES IN THE SECOND BASE
TOP (E). CONNECT THESE BASE TOPS (E) USING THE
PLASTIC WING NUT (I).
E. REPEAT PROCEDUE WITH OTHER BASE TOP (E)
PIECES UNTIL THE BASE TOP (E) IS ONE PIECE.
F. CLOSE THE TANK BY PLACING THE BASE TOP (E)
ONTO THE FILLED BASE BOTTOM (F). ROTATE BASE
TOP (E) UNTIL IT SITS FLAT ON THE BASE BOTTOM
(F). PLACE THE FUNNEL (H) OVER THE LOWER POLE
(B) AND INTO THE CENTER OF THE BASE TOP (E).
Page 2/4

STEP 3
A. CONNECT SOLAR PANEL (G) TO TOP OF
UMBRELLA FRAME (A) BY INSERTING PLUG ON
UMBRELLA FRAME (A) INTO SOCKET ON SOLAR
PANEL (G).
B. SCREW THE SOLAR PANEL (G) ONTO UMBRELLA
FRAME (A).
C. LIFT UMBRELLA FRAME (A) ONTO LOWER POLE
(B). ROTATE UMBRELLA FRAME (A) TO DESIRED
POSITION AND INSERT THE PIN ON LOWER POLE (B)
INTO THE HOLE ON UMBRELLA FRAME (A).
STEP 4
A. REMOVE TIE FROM UMBRELLA.
B. TURN UMBRELLA CRANK UNTIL THE UMBRELLA
STOPS OPENING.
C. PRESS BUTTON ON HANDLE AND LIFT TO
DESIRED POSITION. DO NOT HOLD THE BUTTON
DOWN- ALLOW THE HANDLE TO LOCK INTO
POSITION.
ASSEMBLY INSTRUCTIONS (CONTINUED)
SONOMA OFFSET SOLAR UMBRELLA ASSEMBLY INSTRUCTIONS
Page 3/4

CARE AND CLEANING
1. BEFORE STORING YOUR UMBRELLA, MAKE SURE IT IS COMPLETELY DRY AND CLEAN.
2. KEEP THE UMBRELLA STORED IN A DRY WELL-VENTILATED PLACE TO PROTECT AGAINST MILDEW.
3. USE ONLY MILD CLEANING PRODUCTS ON UMBRELLA. ALLOW UMBRELLA TO DRY THROUGHLY. MILDEW SPOTS CAN
BE REMOVED WITH A MILD CLEANING PRODUCT. NEVER USE CLEANING PRODUCTS THAT CONTAIN SOLVENTS AS
THESE WILL BLEACH AND DAMAGE THE MATERIAL.
4. CLEAN WITH DAMP CLOTH.
TIP: TO AVOID DAMAGE NEVER USE ALKLAI OR ACIDIC CLEANING PRODUCTS OR STEAM CLEANERS TO CLEAN THE
UMBRELLA. TO PREVENT MATERIAL DAMAGE, REMOVE ANY COLLECTED WATER FROM THE CANOPY BY EITHER
DRAINING OFF THE WATER OR DISMANTLING THE UMBRELLA. THE CANOPY IS NOT 100% WATERPROOF AND WATER
CAN SEEP THROUGH THE SEAMS AND OR MATERIAL. THE UMBRELLA PROTECTS YOU FROM THE SUN AND IS NOT A
RAIN SHELTER.
WARNING: UMBRELLA MAY NOT WITHSTAND HIGH WINDS. TO AVOID INJURY OR DAMAGE, DO NOT USE IN HIGH
WIND CONDITIONS. ALWAYS RETRACT UMBRELLA WHEN NOT IN USE. UMBRELLA BASE MUST BE FILLED COMPLETLY
INORDER FOR BASE TO WORK PROPERLY.
WARRANTY
1 YEAR LIMITED WARRANTY. COMERCIAL USE, ACTS OF NATURE, FIRE, FREEZING, ABUSIVE USE, DISCOLORATION OR
FADING OF THE FINISH OR FABRICS AS RESULT OF CHEMICALS OR SPILLS IS NOT COVERED. PROOF OF PURCHASE
(DATED RECEIPT) IS REQUIRED FOR WARRANTY CLAIMS. WE RESERVE THE RIGHT TO MAKE SUBSTITUTIONS WITH
SIMILAR MERCHANDISE.
STEP 5
A. ADJUST THE POSITION OF THE UMBRELLA
CANOPY BY MOVING THE HANDLE UP AND DOWN.
TO ROTATE THE CANOPY REMOVE AND INSERT THE
PIN TO MAINTAIN DESIRED DIRECTION.
B. TO USE SOLAR LIGHTS TURN ON AND OFF USING
SWITCH NEAR HANDLE.
NOTE: SOLAR PANEL MUST BE CHARGED FOR 8
HOURS IN FULL SUNLIGHT FOR BEST RESULTS.
ASSEMBLY INSTRUCTIONS (CONTINUED)
SONOMA OFFSET SOLAR UMBRELLA ASSEMBLY INSTRUCTIONS
Page 4/4