Sony BDP-CX7000ES - 400 Blu-ray Disc Mega Changer User manual

SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
BDP-CX7000ES
SPECIFICATIONS
BLU-RAY DISC/DVD PLAYER
9-889-521-01
2009F05-1
© 2009.06
US Model
Canadian Model
Ver. 1.0 2009.06
Model Name Using Similar Mechanism DVP-CX995V
Mechanism Type CDM89-430AAA
Base Unit Name KEM-430AAA
Optical Pick-up Name KES-430A
sThis product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
sManufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of
Dolby Laboratories.
sManufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and
worldwide patents issued & pending. DTS is a registered trademark
and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio |
Essential are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All
Rights Reserved.
sJava and all Java-based trademarks and logos are trademarks or
registered trademarks of Sun Microsystems, Inc.
s, “XMB,” and “xross media bar” are trademarks of Sony
Corporation and Sony Computer Entertainment Inc.
sThis product incorporates High-Definition Multimedia Interface
(HDMI™) technology. HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
s“Blu-ray Disc” is a trademark.
s“Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVD-R,”
“DVD VIDEO,” and “CD” logos are trademarks.
s“BD-Live” and “BonusView” are trademarks of Blu-ray Disc
s“x.v.Color” and “x.v.Color” logo are trademarks of Sony
s“BRAVIA” is a trademark of Sony Corporation.
s“PhotoTV HD” and the “PhotoTV HD” logo are trademarks of
sMPEG Layer-3 audio coding technology and patents licensed from
Fraunhofer IIS and Thomson.
sThis product meets ENERGY STAR guidelines for energy
efficiency. ENERGY STAR and the ENERGY STAR mark are
registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
sMusic and video recognition technology and related data are
provided by Gracenote®. Gracenote is the industry standard in
music recognition technology and related content delivery. For more
information, please visit www.gracenote.com. CD, DVD, Blu-ray
Disc, and music and video-related data from Gracenote, Inc.,
copyright © 2000-present Gracenote. Gracenote Software,
copyright © 2000-present Gracenote. One or more patents owned
by Gracenote apply to this product and service. See the Gracenote
website for a non-exhaustive list of applicable Gracenote patents.
Gracenote, CDDB, MusicID, MediaVOCS, the Gracenote logo and
logotype, and the “Powered by Gracenote” logo are either
registered trademarks or trademarks of Gracenote in the United
States and/or other countries.
sOther system and product names are generally trademarks or
registered trademarks of the manufacturers. ™ and ® marks are not
indicated in this document.
Association.
Corporation.
Sony Corporation.
System
Laser: Semiconductor laser
Outputs
(Jack name:
Jack type/Output level/Load impedance)
Analog Audio Output:
Stereo Output: Phono jack/2 Vrms/
10 kilohms
Multi Channel Output: Phono jack/2 Vrms/
10 kilohms
Digital Audio Output:
Optical Output: Optical output jack/
–18 dBm (wave length 660 nm)
Coaxial Output: Phono jack/0.5 Vp-p/
75 ohms
Analog Video Output
Component Output (Y, PB, PR): Phono jack/
Y: 1.0 Vp-p/PB, PR: 0.7 Vp-p/75 ohms
Composite Output: Phono jack/1.0 Vp-p/
75 ohms
S-Video Output: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.286 Vp-p/75 ohms
HDMI Output
HDMI 19-pin standard connector
LAN (100):
100BASE-TX Terminal
EXT:
External memory slot (For connecting the
external memory)
DC output: 5 V 500 mA Max
CONTROL S IN/IR IN:
Mini jack
RS232C port:
D-sub 9-pin
General
Power requirements:
120 V AC, 60 Hz
Power consumption:
36 W
Dimensions (approx.):
430 mm × 240 mm × 555 mm
(17 in. × 9 1/2in. × 21 7/8in.)
(width/height/depth) incl. projecting parts
Mass (approx.):
14.2 kg (31 lb 5 oz)
Operating temperature:
5 ºC to 35 ºC (41 °F to 95 °F)
Operating humidity:
25 % to 80 %
Supplied accessories
Specifications and design are subject to
change without notice.
sAudio/video cord (phono plug ×3) (1)
sAC power cord (1)
sRemote commander (remote) (1)
sSize AA (R6) batteries (2)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
2
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 kΩ0.15 μF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia-
tion exposure.
CAUTION
The use of optical instruments with this product will increase eye hazard. As the laser
beam used in this Blu-ray Disc/DVD player is harmful to eyes, do not attempt to
disassemble the cabinet.
Refer servicing to qualified personnel only.
This label is located on the laser protective housin
g
inside the enclosure.
Self-Diagnosis Function
When the self-diagnosis function is activated to prevent the player
from malfunctioning, an error code appears in the front panel display,
or just appears without any messages on the entire screen.
In these cases, check the following.
When an error code appears in the front panel display
Error code Corrective action
Exxxx
SYS ERR
Contact your nearest Sony dealer or local authorized Sony
service facility and give the error code. “xxxx” represents
an error code (number).
FAN ERR sCheck that the ventilation holes on the rear of the player
are not blocked.
sPlace the player in a location with adequate ventilation
to prevent heat build-up in the player.
When turning the player on, appears on the screen, and
“SYSTEM ERROR” appears in the front panel display.
,Disconnect the power cord and wait for a while, then re-connect the
power cord.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
3
1. SERVICING NOTES ............................................. 4
2. DISASSEMBLY
2-1. Disassembly Flow........................................................... 6
2-2. Case................................................................................. 7
2-3. VP-062EJ Board ............................................................. 7
2-4. AUSE Board ................................................................... 8
2-5. MB-124-MEGA-EJ Board.............................................. 8
2-6. Chassis-M (ES) Block .................................................... 9
2-7. Front Panel Block ........................................................... 9
2-8. 400D Table Assy ............................................................. 10
2-9. DRV Board...................................................................... 10
2-10. Table (Door) Assy........................................................... 11
2-11. DC Motor (Door) (M201)............................................... 11
2-12. Holder (Table Sensor 400).............................................. 12
2-13. SDT Board, SDR Board.................................................. 12
2-14. SDO Borad...................................................................... 13
2-15. Pop-up (400) Assy .......................................................... 14
2-16. Back Panel Block............................................................ 14
2-17. BU (KEM-430AAA) Assy.............................................. 15
2-18. Optical Pick-up Block (KEM-430AAA) ........................ 16
2-19. Switching Regulator ....................................................... 17
2-20. Base (CDM BD) Block................................................... 18
2-21. Motor (400BD) Assy (Loding) (M301)/
(Table) (M302), MLD Board .......................................... 18
2-22. SLK Board, SLD Board.................................................. 19
3. TEST MODE ............................................................ 20
4. MECHANICAL ADJUSTMENTS ...................... 27
5. ELECTRICAL ADJUSTMENT ........................... 30
6. DIAGRAMS
6-1. Block Diagram - BD/DVD Section -.............................. 31
6-2. Block Diagram - VIDEO CONTROL Section - ............. 32
6-3. Block Diagram - VIDEO Section -................................. 33
6-4. Block Diagram - AUDIO Section -................................. 34
6-5. Block Diagram - ETHERNET, USB Section - ............... 35
6-6. Block Diagram
- SENSOR, MOTOR DRIVE Section -.......................... 36
6-7. Block Diagram - PANEL Section -................................. 37
6-8. Block Diagram - POWER SUPPLY Section -................ 38
6-9. Printed Wiring Board
- MB-124-MEGA-EJ Board (Component Side) -........... 40
6-10. Printed Wiring Board
- MB-124-MEGA-EJ Board (Conductor Side) - ............ 41
6-11. Schematic Diagram
- MB-124-MEGA-EJ Board (1/10) - .............................. 42
6-12. Schematic Diagram -
MB-124-MEGA-EJ Board (2/10) -................................ 43
6-13. Schematic Diagram
- MB-124-MEGA-EJ Board (3/10) - .............................. 44
6-14. Schematic Diagram
- MB-124-MEGA-EJ Board (4/10) - .............................. 45
6-15. Schematic Diagram
- MB-124-MEGA-EJ Board (5/10) - .............................. 46
6-16. Schematic Diagram
- MB-124-MEGA-EJ Board (6/10) - .............................. 47
6-17. Schematic Diagram
- MB-124-MEGA-EJ Board (7/10) - .............................. 48
6-18. Schematic Diagram
- MB-124-MEGA-EJ Board (8/10) - .............................. 49
6-19. Schematic Diagram
- MB-124-MEGA-EJ Board (9/10) - .............................. 50
TABLE OF CONTENTS
6-20. Schematic Diagram
- MB-124-MEGA-EJ Board (10/10) - ............................ 51
6-21. Printed Wiring Board
- VP-062EJ Board (Component Side) - .......................... 52
6-22. Printed Wiring Board
- VP-062EJ Board (Conductor Side) -............................ 53
6-23. Schematic Diagram - VP-062EJ Board (1/10) - ............. 54
6-24. Schematic Diagram - VP-062EJ Board (2/10) - ............. 55
6-25. Schematic Diagram - VP-062EJ Board (3/10) - ............. 56
6-26. Schematic Diagram - VP-062EJ Board (4/10) - ............. 57
6-27. Schematic Diagram - VP-062EJ Board (5/10) - ............. 58
6-28. Schematic Diagram - VP-062EJ Board (6/10) - ............. 59
6-29. Schematic Diagram - VP-062EJ Board (7/10) - ............. 60
6-30. Schematic Diagram - VP-062EJ Board (8/10) - ............. 61
6-31. Schematic Diagram - VP-062EJ Board (9/10) - ............. 62
6-32. Schematic Diagram - VP-062EJ Board (10/10) - ........... 63
6-33. Printed Wiring Board - AUES Board - ........................... 64
6-34. Schematic Diagram - AUES Board (1/2) - ..................... 65
6-35. Schematic Diagram - AUES Board (2/2) - ..................... 66
6-36. Printed Wiring Boards - CONTROL Section - ............... 68
6-37. Schematic Diagram - CONTROL Section (1/5) -........... 69
6-38. Schematic Diagram - CONTROL Section (2/5) -........... 70
6-39. Schematic Diagram - CONTROL Section (3/5) -........... 71
6-40. Schematic Diagram - CONTROL Section (4/5) -........... 72
6-41. Schematic Diagram - CONTROL Section (5/5) -........... 73
6-42. Printed Wiring Boards - MOTOR DRIVE Section - ...... 74
6-43. Schematic Diagram - MOTOR DRIVE Section -........... 75
6-44. Printed Wiring Boards - SENSOR Section - .................. 76
6-45. Schematic Diagram - SENSOR Section -....................... 76
6-46. Printed Wiring Boards - ETHERNET, USB Section -.... 77
6-47. Schematic Diagram - ETHERNET, USB Section - ........ 77
6-48. Printed Wiring Boards - PANEL Section - ..................... 78
6-49. Schematic Diagram - PANEL Section -.......................... 79
6-50. Printed Wiring Boards - CONNECTOR Section - ......... 80
6-51. Schematic Diagram - CONNECTOR Section -.............. 80
7. EXPLODED VIEWS
7-1. Overall Section ............................................................... 124
7-2. Chassis-M Section .......................................................... 125
7-3. Table Section................................................................... 126
7-4. Front Panel Section......................................................... 127
7-5. Power Block Section....................................................... 128
7-6. Chucking Section............................................................ 129
7-7. Table Sensor Section....................................................... 130
7-8. Chassis Section ............................................................... 131
7-9. Base (Door) Section........................................................ 132
7-10. Pop-up Section................................................................ 133
7-11. Holder Section ................................................................ 134
7-12. Mechanism Base Section................................................ 135
7-13. Base Unit Section (BU (KEM-430AAA) Assy) ............. 136
8. ELECTRICAL PARTS LIST .............................. 137
Accessories are given in the last of the electrical parts list.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
4
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE WHEN PARTS THAT CANNOT BE SUPPLIED
ARE REPLACED
There are parts that cannot be exchanged with single parts in this
set. The following parts are damaged, exchange the entire mounted
board.
MB-124-MEGA-EJ board: IC101, IC102, IC103, IC202, IC203,
IC307, IC308, IC501, IC601, IC602,
IC700, IC701, IC8001
VP-062EJ board : IC204, IC301, IC401, IC501, IC602,
IC603, IC606, IC607, IC1003, IC1201
ABOUT THE LENS CLEANING
Do not do the lens cleaning with the cotton bud etc. It causes the
trouble.
NOTE THE OPTICAL PICK-UP BLOCK AND DR-510
BOARD REPLACING
Exchange both at the same time when exchange Optical Pick-up
Block (KES-430A) or DR-510 board.
As for the service parts, these two parts are supplied by the set.
Part No. Description Layer
J-6090-199-A BLX-104 Single Layer
J-6090-200-A BLX-204 Dual Layer
3-702-101-01 CD (YEDS-18)
J-6090-088-A HLX-504 Single Layer (NTSC)
J-6090-089-A HLX-505 Dual Layer (NTSC)
J-6090-077-A HLX-506 Single Layer (PAL)
J-6090-078-A HLX-507 Dual Layer (PAL)
TEST DISC
Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select 23.976Hz/1080p.
2. Play “4.Motion picture”.
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/S Video/component/HDMI.
Audio:
Speaker out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
* When the output of HDMI is 1080p, the signal of Composite/S
Video/Component are not output.
It is necessary to lower the output of HDMI to 1080i or less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play “4.Motion picture”.
3. Check whether player can play back or not.
(Check the picture and sound output)
3. CD (YEDS-18)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-504/505 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select “1.Video signal”.
2. Play “1.Color bar 100%”.
(Check the picture and sound output)
3. Return to Menu.
4. Play “Demonstration 4:3” or “Demonstration 16:9”.
(Check the picture and sound output)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
5
ALIGNMENT OF GEAR (CAM) PHASE WITH DOOR ASSY
MB-124-MEGA-EJ AND VP-062EJ BOARDS SERVICE POSITION
• It is necessary to connect MB-124-MEGA-EJ board (CN904) and IMD (ES) board (CN3005) with the extension cable to do the setting
to this position.
Prepare the following extension cables.
Part No. J-2501-068-A (19 pin, 1.00 mm pitch) MB-124-MEGA-EJ board
VP-062EJ board
insulation
Connect jig (extension cable)
to the IMD board (CN3005)
CN904
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C106) to
discharge the capacitor (C106).
HARNESS SETTING ON SWITCHING REGULATOR
Note: This illustration sees the switching regulator from component side.
door assy gear (cam)
Align a slit of door assy with a marking on
the bottom land of gear tooth when the gear
is rotated fully in arrow direction, as shown.
C106
800 :/2 W
–
Switching Regulator (Conductor Side) –
clamp (L35)
AC inlet (2P) harness
harness wire
switching
regulator
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
6
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. CASE
(Page 7)
2-3. VP-062EJ BOARD
(Page 7)
2-4. AUES BOARD
(Page 8)
2-6. CHASSIS-M (ES) BLOCK
(Page 9)
2-7. FRONT PANEL BLOCK
(Page 9)
2-5. MB-124-MEGA-EJ BOARD
(Page 8)
2-8. 400D TABLE ASSY
(Page 10)
2-9. DRV BOARD
(Page 10)
2-10. TABLE (DOOR) ASSY
(Page 11)
2-11. DC MOTOR (DOOR) (M201)
(Page 11)
2-17. BU (KEM-430AAA) ASSY
(Page 15)
2-19. SWITCHING REGULATOR
(Page 17)
2-20. BASE (CDM BD) BLOCK
(Page 18)
2-18. OPTICAL PICK-UP BLOCK
(KEM-430AAA)
(Page 16)
2-12. HOLDER (TABLE SENSOR 400)
(Page 12)
2-14. SDO BOARD
(Page 13)
2-21. MOTOR (400 BD) ASSY (LOADING) (M301)/
(TABLE) (M302), MLD BOARD
(Page 18)
2-22. SLK BOARD, SLD BOARD
(Page 19)
2-15. POP-UP (400) ASSY
(Page 14)
2-13. SDT BOARD, SDR BOARD
(Page 12)
2-16. BACK PANEL BLOCK
(Page 14)
SET
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
7
1five screws (BVST4 u8)
2two flat head screws (TP)
2three flat head screws (TP)
1five screws (BVST4 u8)
3case
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE
2-3. VP-062EJ BOARD
4five screws
(BVTP3 u8)
4five screws (BVTP3 u8)
5connector (CN104)
6VP-062EJ board
3screw (B3 u6)
1connector (CN802)
2wire (flat type)
(21 core) (CN801)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
8
3two screws (BVTP3 u8)
4five screws (BVTP3 u8)
3screw (BVTP3 u8)
5AUES board
1connector (CN102)
2wire (flat type)
(26 core) (CN101)
2-4. AUES BOARD
2-5. MB-124-MEGA-EJ BOARD
3two connectors
(CN301, CN600)
4SATA harness
(CN700)
1wire (flat type) (26 core)
(with ferrite core) (CN803)
6two screws (BVTP3 u8) 6three screws (BVTP3 u8)
7three solders
8heat sink (ES)
9radiation sheet (F)
0MB-124-MEGA-EJ board
2wire (flat type)
(21 core) (CN801)
5wire (flat type)
(19 core) (CN904)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
9
2-6. CHASSIS-M (ES) BLOCK
2-7. FRONT PANEL BLOCK
7six connectors
(CN2501, CN2514, CN2503,
CN3001, CN4001, CN4002)
5wire (flat type) (15 core)
(CN3012)
3connectors
(CN2511)
2SATA harness (CN700)
4cushion
6two connectors
(CN3009, CN3011)
0four screws (BVTP3 u8)
0three screws (BVTP3 u8)
0three screws (BVTP3 u8)
8two screws (BVTT3 u8)
9two wires
qs chassis-M (ES) block
qa
A
A
BCDEF
G
B
C
F
E
DG
1Cut the wire
holder.
3connector
(CN3011)
2wire (flat type)
(15 core) (CN3012)
1cushion
4six screws (BV/ring)
5front panel block
4five screws (BV/ring)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
10
2-8. 400D TABLE ASSY
2-9. DRV BOARD
Note:
When installing the guide (door),
align the positions as shown.
1two screws (BVTP3 u8)
1two screws (BVTP3 u8)
2panel sub block
1two screws
(BVTP3 u8)
3screw
(PWH2)
4guide (door)
5400D table assy
1four screws (BVTP3 u8)
1two connectors
(CN101, CN102)
2connector
(CN103)
3two connectors
(CN104, CN105)
4two screws (BVTP3 u8)
5DRV board
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
11
2-10. TABLE (DOOR) ASSY
2-11. DC MOTOR (DOOR) (M201)
1three screws (BVTP3 u8)
2cover (table)
3door (disc) assy
5table (door) assy
4two screws (BVTP3 u8)
4eight screws (BVTP3 u8)
2two screws (BVTP3 u8)
3Remove two solders.
4MDO board
6DC motor (door) (M201)
DC motor (door) (M201)
Installation position
5pulley (motor CDM)
pulley (motor CDM)
1belt (DIA42 u1.2) 2.5 mm ± 0.1 mm
table (door) assy
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
12
2-12. HOLDER (TABLE SENSOR 400)
2-13. SDT BOARD, SDR BOARD
1four screws (BVTP3 u6)
5screw
(PTTWH3 u6)
6two claws
6claw
2connector
(CN901)
7holder
(table sensor 400)
3two connectors
(CN902, CN903)
4STB board
chassis block
1screw
(PTTWH3 u6)
5screw
(PSW3 u8)
7screw
(PSW3 u8)
2clamp
6SDT board
8SDR board
3two step screws (T1)
4bracket (sensor 400)
chassis block
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
13
2-14. SDO BOARD
5two screws
(BVTP2.6)
3screw (PTPWH2.6)
1screw (PTPWH2.6)
1Move the slider (pop-up) and the lever (pu joint) fully
in the direction of the arrow A.
2Install the gear (cam) in the direction shown
in the illustration and rotate it fully
in the direction of the arrow B.
3When the gear (cam) happens to go too deep,
return it to the original position
in the direction of the arrow C.
4gear (B)
base (door) block
2gear (cam)
6SDO board
C
B
Alever (pu joint)
two rotary switches
slider (pop-up)
gear (cam)
SDO board
The levers of the two rotary switches on the DOOR SW board
are shown in the illustration below.
Precaution during the gear (cam) installation
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
14
2-16. BACK PANEL BLOCK
3Cut the wire holder.
4six screws
(BVTP3 u8)
4three screws
(BVTP3 u8)
1nine screws
(BVTP3 u8)
4four screws
(BVTP3 u8)
2cover (CDM_T) block
4four screws
(BVTP3 u8)
5back panel block
2-15. POP-UP (400) ASSY
1screw (PTPWH3 u6) chassis block
2step screw
3pop-up (400) assy
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
15
2-17. BU (KEM-430AAA) ASSY
6four screws
(BVTP3 u8)
6four screws
(BVTP3 u8)
6two screws
(BVTP3 u8)
0two screws
(BVTP3 u8)
qa BU (KEM-430AAA) assy
Note: Refer to the servicing notes “NOTE
THE OPTICAL PICK-UP BLOCK
AND DR-510 BOARD REPLACING”
(page 4), if replacing this part.
3SATA harness (CN001)
5sarannet cushion (SQ)
4connector
(CN900)
1three screws
(BVTP3 u8)
2bracket (corner)
7bracket (top BD) block
8torsion holder (magnet) block
9torsion spring (MG)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
16
2-18. OPTICAL PICK-UP BLOCK (KEM-430AAA)
Note: Refer to the servicing notes “NOTE THE OPTICAL PICK-UP BLOCK AND DR-510 BOARD REPLACING” (page 4) if replacing the opti-
cal pick-up block or DR-510 board.
8optical pick-up block
(KEM-430AAA)
1flexible flat cable
(CN521)
6two float screws (S)
Align as the same length.
flexible flat cable
Bend down the edge.
flat clamp
side view
6two float screws (S)
7two insulators
7two insulators
2flexible flat cable
(CN301)
4flexible flat cable
5flat clamp (20)
3DR-510 board block
Arrangement of flexible flat cable
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
17
2-19. SWITCHING REGULATOR
1three screws (BVTP3 u8)
8four screws (BVTP3 u8)
8screw (BVTP3 u8)
9clamp (L35)
clamp (L35)
AC inlet (2P) harness
harness wire
0bracket (power ES) assy
qa switching regulator
switching regulator
2cover (disc rear)
3three rivets
4shield plate power
5three connectors
(CN202, CN204, CN205)
6two connectors
(CN201, CN203)
7connector (CN101)
1three screws (BVTP3 u8)
Arrangement of harness
Note: This illustration sees the switching regulator from component side.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
18
2-20. BASE (CDM BD) BLOCK
2-21. MOTOR (400 BD) ASSY (LOADING) (M301)/(TABLE) (M302), MLD BOARD
4twelve screws (BVTP3 u8)
5base (CDM BD) block
1screw (PSW3 u8)
3screw (PSW3 u8)
2shaft (pole)
5motor (400 BD) assy (table)
(M302)
6MLD board
4motor (400 BD) assy (loading)
(M301)
1two belts (BD)
2three screws (BVTP3 u8)
3two solders
3two solders
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
19
2-22. SLK BOARD, SLD BOARD
claws
Note for installation
When installing the
SLK board and SLD boards,
align the leads position as shown.
SLK board
SLD board
leads
position
A
B
1Rotate the gear (pulley BD) in the
direction of the arrow Afully.
3Rotate the gear (pulley BD) in the
direction of the arrow Bfully.
2screw (BVTP3 u8)
4screw (BVTP3 u8)
0screw (BVTP3 u8)
5SLK board
qa SLD board
6belt (BD)
7screw (PWH2)
base (CDM BD) block
8gear (pulley BD)
9gear (center BD)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

BDP-CX7000ES
20
SECTION 3
TEST MODE
1. BD SERVICE MODE
Note: The operation in this mode must use a remote commander.
1-1. Setting method of the BD service mode:
1. It is confirmed that the AC power cord is pulled out.
2. Press the [x], [OPEN/CLOSE] and [DISC EJECT] buttons, next the AC power cord is inserted.
3. The message “SERVICE MODE” appears on the fluorescent indicator tube and enter the BD service mode (it keeps pressing the buttons
until the message is displayed).
1-2. Menu composition
1. Diag (test function)
2. Log (log display)
3. Factory Initialize (returns to the state of the factory shipment)
4. Ship Mode (ship mode setting and power off)
5. Network (network information display)
6. System Information (system information display)
1-3. Menu tree
Service Mode Menu Diag
Log
Factory Initialize
Ship Mode
Network
System Information
Device Test
Audio Video Test
Changer Mecha Test
Error Log
Command Log
Ifconfig
Ping
USB Host
D/A Converter
Ifcon
I/P Converter
Glue
HD Enhancer
Video Encoder
External HDMI
Initialize
Popper Up/Down
Open/Close
Turn Left
Turn Right
Turn Around Left
Turn Around Right
Chuck/Unchuck
FDP All ON
Show Strings
LED Sequential ON
Fan Control ON
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com