Sony Handycam DCR-IP1 User manual

SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
LEVEL 2
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
W100 MECHANISM
Ver 1.0 2003. 10
•For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987626751.pdf).
•For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL1 (987626741.pdf).
•For MECHANISM ADJUSTMENTS, refer to the “MICRO MV MECHANICAL ADJUSTMENT MANUAL 2
W MECHANISM ” (9-876-276-11).
•Reference No. search on printed wiring boards is available.
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
•TO TAKE OUT A CASSETE WHEN NOT EJECT (FORCE EJECT)
DCR-IP1/IP1E
RMT-832
On the CD-458 and VC-333 boards
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the CD-458 and VC-333 boards.
Therefore, schematic diagrams, printed wiring boards, mounted parts location and electrical parts list of the CD-458 and VC-
333 boards are not shown.
The following pages are not shown.
Schematic diagrams ...........................Pages 4-9 to 4-46
Printed wiring boards ..........................Pages 4-65 to 4-70
Mounted parts location .................. Pages 4-85 to 4-87
Electrical parts list.........................Pages 5-14 and 5-18 to 5-26
How to use
Acrobat Reader
How to use
Acrobat Reader
US Model
Canadian Model
Korea Model
DCR-IP1
AEP Model
UK Model
East European Model
Chinese Model
Australian Model
Hong Kong Model
DCR-IP1E
E Model
Tourist Model
DCR-IP1/IP1E

— 2 —
DCR-IP1/IP1E
SPECIFICATIONS
Video camera recorder
System
Video recording system
2 rotary heads
Helical scanning system
Still image recording system
Exif Ver. 2.2*
Audio recording system
MPEG1 Audio Layer2
(Fs 48 kHz, stereo)
Video signal
PAL color, CCIR standards
Usable cassette
MICROMV cassette with the
m
DCR-IP1:
DCR-IP1E:
NTSC color, EIA standards
ark printed
Tape speed
Approx. 5.66 mm/s
Recording/playback time (using an MGR60
cassette)
Approx. 60 min
Fast forward/rewind time (using a MGR60
cassette)
Approx. 1 min, and 30 s
Image device
3.6 mm (1/5.0 type) CCD (Charge
Coupled Device)
Gross: Approx. 1 070 000 pixels
Effective (still): Approx. 1 000 000
pixels
Effective (moving): Approx. 690 000
pixels
Lens
Carl Zeiss Vario-Sonnar
Combined power zoom lens
10 × (Optical), 120 × (Digital)
F = 1.8 ~ 2.3
Focal length
3.2 - 32 mm (5/32 - 1 5/16 in.)
When converted to a 35 mm still camera
In CAMERA-TAPE:
46 - 460 mm (1 13/16 - 18 1/8 in.)
In CAMERA-MEM:
38 - 380 mm (1 1/2 - 15 in.)
Color temperature
[AUTO], [HOLD], [INDOOR] (3 200
K), [OUTDOOR] (5 800 K)
Minimum illumination
7 lx (lux) (F 1.8)
*Exifisafile format for still images, established
by the JEITA (Japan Electronics and
Information Technology Industries
Association). Files in this format can have
additional information such as camera settings.
Input/Output connectors
Audio/Video input/output
10-pin connector
Input/output auto switch
Video signal: 1 Vp-p, 75 Ω(ohms),
unbalanced, sync negative
Luminance signal: 1 Vp-p, 75 Ω(ohms),
unbalanced
Chrominance signal:
DCR-IP1: 0.286 Vp-p,
DCR-IP1E: 0.3 Vp-p,
75 Ω(ohms), unbalanced
Audio signal: 327 mV, (at output
impedance more than 47 kΩ(kilohms))
Input impedance more than 47 kΩ
(kilohms)
Output impedance with less than 2.2 kΩ
(kilohms)
LCD screen
Picture
5.0 cm (2.0 type)
Total dot number
211 200 (960 × 220)
General
Power requirements
DC 7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
Averagepowerconsumption(whenusingthe
battery pack)
During camera recording using LCD
with the normal brightness
3.8 W
Operating temperature
0C to 40 C (32 F to 104 F)
Storage temperature
-20 C to + 60 C (-4 F to + 140 F)
Dimensions (approx.)
39 × 91 ×69 mm (1 9/16 ×3 5/8 ×2 3/4
in.) (w/h/d)
Mass (Approx.)
230 g (8 oz) main unit only
280 g (10 oz) including the NP-FF51
rechargeable battery pack, MGR60
cassette.
Supplied accessories
Handycam Station DCRA-C100
Audio/Video input/output
10-pin connector
Input/output auto switch
Video signal:1 Vp-p, 75 Ω(ohms),
unbalanced, sync negative
Luminance signal: 1 Vp-p, 75 Ω(ohms),
unbalanced
Audio signal: 327 mV, (at output
impedance more than 47 kΩ(kilohms))
Input impedance more than 47 kΩ
(kilohms)
Output impedance with less than 2.2 kΩ
(kilohms)
USB jack
mini-B
i.LINK (MICROMV) input/output
4-pin connector S400
AC Adaptor AC-L25A/L25B
Power requirements
AC 100 - 240 V, 50/60 Hz
Current consumption
0.35 - 0.18 A
Power consumption
18 W
Output voltage
DC 8.4 V, 1.5 A
Operating temperature
0C to 40 C (32 F to 104 F)
Storage temperature
-20 C to + 60 C (-4 F to + 140 F)
Dimensions (approx.)
56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.)
(w/h/d) excluding projecting parts
Mass (approx.)
190 g (6.7 oz) excluding the power cord
Rechargeable battery pack (NP-FF51)
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
5.6 Wh (780 mAh)
Operating temperature
0C to 40 C (32 F to 104 F)
Dimensions (approx.)
40.8 × 12.5 × 49.1 mm (1 5/8 × 1/2 ×1
15/16 in.) (w/h/d)
Mass (approx.)
45 g (1.6 oz)
Type
Lithium ion
Design and specifications are subject to change
without notice.
Memory Stick Duo adaptor (1)
AC Adaptor (1)
Power cord (1)
Handycam Station DCRA-C100 (1)
Wireless Remote Commander (1)
A/V connecting cable (1)
USB cable (1)
Hand strap (1)
Rechargeable battery pack NP-FF51 (1)
Battery terminal cover (1)
MICROMV (1)
Cleaning cloth (1)
Camera Operations Guide (1)
Computer Applications Guide (1)
MovieShaker Applications Guide (1)
21-pin adaptor (1)
(AEP, UK, EE)
2-pin conversion adaptor (1)
(E, HK, JE)
See page 5-27.
Chrominance signal:
DCR-IP1: 0.286 Vp-p,
DCR-IP1E: 0.3 Vp-p,
75 Ω(ohms), unbalanced
Memory Stick Duo 8MB (1)
CD-ROM SPVD-010 USB Driver (1)
CD-ROM MovieShaker Ver.3.1 for
•Abbreviation
AUS:Australian model
CH : Chinese model
CND: Canadian model
EE : East European model
JE : Tourist model
HK : Hong Kong model
KR : Korean model

— 3 —
DCR-IP1/IP1E
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. Checktheareaofyour repair for unsoldered or poorly-soldered
connections. Check the entireboardsurfacefor solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which,through functioning, showobvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

— 4 —
DCR-IP1/IP1E
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Note for Repair ································································1-1
1-2. Power Supply During Repairs ·········································1-1
1-3. To Take Out a Cassette when not Eject (Force Eject) ·····1-2
1-4. Self-diagnosis Function
1-4-1.Self-diagnosis Function ···················································1-3
1-4-2.Self-diagnosis Display·····················································1-3
1-4-3.Self-diagnosis Code Table ···············································1-4
2. DISASSEMBLY
Service Position: LCD Module ·······································2-3
Service Position to Check the VTR Section ····················2-4
2-1. Top Cabinet Assembly ·····················································2-5
2-2. F Panel BlockAssembly··················································2-5
2-3. Gear With Motor (Lens Cover) (M904),
FP-731 Flexible Board ····················································2-6
2-4. Lens Shutter, Lens Ornamental Plate ······························2-6
2-5. Cabinet R Block Assembly··············································2-7
2-6. FP-732/FP-734 Flexible Board ·······································2-7
2-7. MS-153 Board ·································································2-8
2-8. PD-199 Board, LCD Module ··········································2-8
2-9. Hinge Assembly, FP-733 Flexible Board ························2-9
Installation of FP-733 Flexible Board ···························2-10
2-10. IF-108 Board ·································································2-11
2-11. SE-139 Board, Mic Unit················································2-11
2-12. Lens Block Assembly ····················································2-12
2-13. CD-458 Board ·······························································2-12
2-14. Cabinet G·······································································2-13
2-15. Cabinet L Assembly ······················································2-13
2-16. VC-333 Board ·······························································2-14
2-17. Mechanism Deck ···························································2-14
2-18. Operation Switch Block (PW4720)·······························2-15
2-19. Grip Cover ·····································································2-15
2-20. Circuit Boards Location ················································2-16
2-21. Flexible Boards Location ··············································2-17
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/6)···········································3-1
3-2. Overall Block Diagram (2/6)···········································3-3
3-3. Overall Block Diagram (3/6)···········································3-5
3-4. Overall Block Diagram (4/6)···········································3-7
3-5. Overall Block Diagram (5/6)···········································3-9
3-6. Overall Block Diagram (6/6)·········································3-11
3-7. Power Block Diagram (1/3)···········································3-13
3-8. Power Block Diagram (2/3)···········································3-15
3-9. Power Block Diagram (3/3)···········································3-17
Section Title Page Section Title Page
4. PRINTEDWIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagrams
Frame Schematic Diagram (1/2) ·····································4-1
Frame Schematic Diagram (2/2) ·····································4-3
4-2. Schematic Diagrams························································4-5
FP-723 FLEXIBLE (CCD IMAGER) ·····························4-7
PD-199 (LCD DRIVE)··················································4-47
IF-108 (CRADLE TERMINAL) ···································4-49
MS-153 (MS CONNECTOR) ·······································4-51
SE-139 (PITCH/YAW SENSOR)··································4-53
DH-041, FP-080, FP-081, FP-228 FLEXIBLE·············4-55
FP-731, FP-769 FLEXIBLE··········································4-56
FP-732, FP-733, FP-734 FLEXIBLE····························4-57
CF4720, SS4720, PW4720
(CONTROL SWITCH BLOCK)···································4-59
4-3. Printed Wiring Boards ···················································4-63
PD-199···········································································4-71
IF-108 ············································································4-73
MS-153 ··········································································4-75
SE-139 ···········································································4-77
DH-041, FP-080, FP-081, FP-228 FLEXIBLE·············4-79
FP-731, FP-769 FLEXIBLE··········································4-80
FP-732, FP-733, FP-734 FLEXIBLE····························4-81
4-4. Mounted Parts Location ················································4-88
5. REPAIR PARTS LIST
5-1. Exploded Views ····························································5-2
5-1-1. Overall Assembly ··························································5-2
5-1-2. F Panel Block Assembly ···············································5-3
5-1-3. Cabinet R Block Assembly-1········································5-4
5-1-4. Cabinet R Block Assembly-2········································5-5
5-1-5. Cabinet L BlockAssembly-1 ········································5-6
5-1-6. Cabinet L BlockAssembly-2 ········································5-7
5-1-7. Lens Block Assembly ···················································5-8
5-1-8. Mic Block Assembly·····················································5-9
5-1-9. MD Frame BlockAssembly ·······································5-10
5-1-10. Overall Mechanism Deck Section (W100) ·················5-11
5-1-11. LS Chassis BlockAssembly ·······································5-12
5-1-12. Mechanism Chassis BlockAssembly ·························5-13
5-2. Electrical Parts List ·····················································5-14

1-1
SECTION 1
SERVICE NOTE
DCR-IP1/IP1E
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
1-2. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
The following method is available to prevent this.
Method 1.
Use the AC power adaptor (AC-L25A/L25B etc.).

1-2
DCR-IP1/IP1E
1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1Refer to “SECTION 2 DISASSEMBLY” to remove the mechanism deck block.
2Disconnect CN101 (31P) of VC-333 board.
3Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette compartment.
DC power supply
(+5V)
Disconnect CN101 of
VC-333 board

1-3
DCR-IP1/IP1E
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD what to do. This
function consists of two display; self-diagnosis display and service
mode display.
Detailsoftheself-diagnosisfunctionsareprovidedin the Instruction
manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
LCD shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the
“repairedby:”,“block”inwhichthe problem occurred, and “detailed
code” of the problem.
1 1
3 1C
Repaired by:
Refer to 1-4-3. Self-diagnosis Code Table .
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
LCD
C : 3 1 : 1 1

1-4
DCR-IP1/IP1E
1-4-3. Self-diagnosis CodeTable
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Block
Function
04
21
22
31
31
31
31
31
31
31
31
31
31
31
31
31
32
32
32
32
32
32
32
32
32
32
32
32
32
Detailed
Code
00
00
00
10
11
20
21
22
23
30
31
40
41
42
43
44
10
11
20
21
22
23
30
31
40
41
42
43
44
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading .
S reel side tape slacking when unloading .
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum operations.
PG fault during normal drum operations.
Phase fault during normal drum operations.
LOAD direction loading motor time-
out.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan
operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum
operations.
PG fault during normal drum
operations.
Phase fault during normal drum
operations.
Self-diagnosis Code
Repaired by:
Correction
Use the InfoLITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.

1-5E
DCR-IP1/IP1E
E
E
E
E
Block
Function
61
61
62
62
Detailed
Code
00
10
00
01
Symptom/State
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(Withpitchangularvelocity sensoroutput
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Self-diagnosis Code
Repaired by:
Correction
Inspect the lens block focus MR sensor (Pins qk, ql of CN5001 of
CD-458 board) when focusing is performed when the touch panel
is operated in the focus manual mode and the focus motor drive
signals(Pins1,2ofCN5001ofCD-458 board) when thefocusing
is not performed.
Inspect the lens block zoom reset sensor (Pin qg of CN5001 of
CD-458 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive signals (Pins wf to wj of
CN5001 of CD-458 board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE2702 of SE-139 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE2701 of SE-139 board)
peripheral circuits.

DCR-IP1/IP1E
2-1 2-2
HELP
HELP
LCD
SERVICE POSITION
MECHANISM DECK
SERVICE POSITION
DISASSEMBLY DISASSEMBLY
DISASSEMBLY
DISASSEMBLY DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
HELP
HELP
DISASSEMBLY
HELP
HELP
HELP
HELP
HELP HELP HELP
SECTION 2
DISASSEMBLY
The following flow chart shows the disassembly procedure.

DCR-IP1/IP1E
2-3 2-4
[SERVICE POSITION TO CHECK THE VTR SECTION]
VC-333 board
IF-108 board
IF-108 board
FP-732 flexible board
FP-722 flexible board
Cabinet R block assembly
Lens block assembly
CN107 (No Mount)
CPC
Mechanism deck
To eject the cassette, short the circuit between
Pin 0and between Pin qa (GND) pattern on
IF-108 board of CN2604 for 1 second.
10
11
CN2604
AC power adaptor AC IN
Adjustment remote commander
(RM-95)
Connection to Check theVTR Section
To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the "ForcedVTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02 and
press the PAUSE button of the adjustment remote
commander.
Note: Although the following message is displayed when a power supply is switched on,
it is because the front panel is removed and this is normal.
Lens cover is not closed. Turn the power on again.
Exiting the "ForcedVTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Procedure of removing mechanismdeck (Mechanism deck service position)
12-1. Top cabinet assembly ............................................. (PAGE 2-5)
22-2. F panel block assembly .......................................... (PAGE 2-5)
32-5. Cabinet R block assembly ...................................... (PAGE 2-7)
42-6. FP-732/FP-734 flexible board................................. (PAGE 2-7)
52-10. IF-108 board......................................................... (PAGE 2-11)
62-11. SE-139 board, Mic unit......................................... (PAGE 2-11)
72-12. Lens block assembly ............................................ (PAGE 2-12)
82-14. Cabinet G ............................................................. (PAGE 2-13)
92-15. Cabinet L assembly .............................................. (PAGE 2-13)
q; 2-16. VC-333 board ....................................................... (PAGE 2-14)
qa 2-17. Mechanism deck................................................... (PAGE 2-14)
ACX510CMN-J (LCD901)
PD-199 board AC power adaptor
AC IN
Adjustment remote commander (RM-95)
[SERVICE POSITION: LCD MODULE]

2-5
DCR-IP1/IP1E
Note: Follow the disassembly procedure in the numerical order given.
2-1. TOP CABINET ASSEMBLY
6Two claws
57Top cabinet assembly
4Screw (M1.7)
2Open the P cabinet block assembly.
3Turn the P cabinet block assembly.
1Screw (M1.7)
3Screw (M1.7)
6FP-731flexible board
(CN2602)
5
7F panel block assembly
4Screw (M1.7)
2Screw (M1.7)
1Close the P cabinet block assembly.
2-2. F PANEL BLOCK ASSEMBLY

2-6
DCR-IP1/IP1E
2-3. GEAR WITH MOTOR (LENS COVER) (M904), FP-731 FLEXIBLE BOARD
2Two screws (M1.7X3.5)
3Connector
(CN7311)
6Gear with motor (Lens cover)
(M904)
4Two solders
5FP-769 flexible board
1Draw out the FP-769 flexible board
in a direction of the arrow.
At this time, take care not to damage
the flexible board.
Note: When mounting the geared motor,
meet a convex portion of the gear with a
concave portion of the shutter lever.
Shutter lever concave portion
Gear convex portion
8Two screws (M1.7X3.5)
7Screw
(M1.7X3.5)
9FP-731 flexible board
1Screw (M1.7X3.5)
3Shutter retainer
4Shutter lever
5Lens shutter
2Screw (M1.7X3.5)
6Two screws (M1.7X3.5)
7Lens ornamental plate
2-4. LENS SHUTTER, LENS ORNAMENTAL PLATE

2-7
DCR-IP1/IP1E
2-6. FP-732/FP-734 FLEXIBLE BOARD
3Screw (M1.7)
2Screw (M1.7X2.5)
1Open the P cabinet block assembly.
4Two screws
(M1.7X2.5)
7FP-732 flexible board
(CN2605)
6Paying attention to the FP-732 flexible board,
raise the cabinet R block assembly a little.
9Cabinet R block assembly
8FP-720 flexible board
(CN109)
5Close the P cabinet block assembly.
Note: Pell of the flexible board a little by little,
not applying an excessive force,
as it is adhered strongly with the panel sheet.
7Two solders
8Lithium battery (secondary)
5Two claws
qa FP-734 flexible board
4SP retainer assembly
6Flexible board
(CN2904)
2FP-733 flexible board (CN2903)
q; Loud speaker (1.6cm)
9Two solders
1Panel sheet
qj FP-732 flexible board
qh Battery terminal board
(BT901)
qf
qg Six solders qd Three screws (M1.7X4)
qs Open the jack cover assembly.
3Two screws (M1.7X2.5)
2-5. CABINET R BLOCK ASSEMBLY

2-8
DCR-IP1/IP1E
2-7. MS-153 BOARD
2Screw (M1.7X2.5)
1MS sheet
6MS-153 board
5FP-720 flexible board (CN2902)
3Paying attention to the
operation switch block,
remove two convex portions
of the board.
4Control switch block (CF4720)
(CN2901)
Control switch block
(CF4720)
1
9FP-733 flexible board
(CN3501)
3Screw (M1.7X4)
8Screw
(M1.7X2.5)
q; P cabinet L block
5Screw (M1.7X4)
6Two claws
7P cabinet R assembly
24
qs Flexible board
(CN3504)
qd Flexible board
(CN3502)
qf Flexible board
(CN3503)
ws Panel lock retainer
wd LCD module
wf P cushion
qk PD-199 board
qh
qg Claw
qa Screw
(M1.7X2.5)
wh P cabinet L
w; Two claws
wa LCD fixed plate
ql Screw
(M1.7X2.5)
qj PD sheet
wg Light interception sheet
2-8. PD-199 BOARD, LCD MODULE

2-9
DCR-IP1/IP1E
2-9. HINGE ASSEMBLY, FP-733 FLEXIBLE BOARD
A
1
4Two claws
qg Four claws
7Two claws
9Magnet
5Hinge cover (front)
8Hinge cover (rear)
3Paying attention to the
FP-733 flexible board,
remove the hinge assembly.
0Remove an H-shaped part of the
FP-733 flexible board from the hinge assembly.
qj FP-733 flexible board
qa Rotate the FP-733 flexible board
in the arrow Adirection to remove,
which winds around the hinge assembly.
qs Remove the flexible clamper
from the hinge assembly.
qf Remove the IC7301 part
from the flexible clamp.
qh Flexible clamp
2Two screws
(M1.7
X 4)
6Screw (M1.7
X 4)
qd Hinge assembly

2-10
DCR-IP1/IP1E
[INSTALLATION OF FP-733 FLEXIBLE BOARD]
A
2Engage four claws.
6Meet an H-shaped part
of the FP-733 flexible board
with the claws of the hinge assembly.
7When the FP-733 flexible board
was mounted on the PD-199 board,
bend a slack portion as shown in the figure.
claws
5Wind the FP-733 flexible board
around the hinge assembly in the
arrow Adirection.
4Mount the flexible clamper
on the hinge assembly.
Hinge assembly
3Meeting with the bosses,
mount the IC7301 part
on the flexible clamper.
Bosses
1Fold the FP-733 flexible board.
Flexible clamp
FP-733 flexible board
FP-733 flexible board
Fold
Fold
Fold
Fold
Fold
PD-199 board side
PD-199
board side
PD-199 board side
MS-153 board side
MS-153 board side
MS-153
board side
: Fold mark : Fold mark

2-11
DCR-IP1/IP1E
2-10.IF-108 BOARD
7Two claws
8CR cover
1Flexible board (CN2604)
5FP-722 flexible board
(CN105)
2Two screws
(M1.7X2.5)
3Screw (M1.7X2.5)
4
6FP-722 flexible board
(CN2605)
9IF-108 board
2Mic block assembly
6SE-139 board
9SE frame
qa Microphone unit
1Screw (M1.7X2.5)
4Screw (M1.7X2.5)
7Screw (M1.7X2.5)
3Flexible board (CN106)
5Flexible board
(CN2701)
qs Connctor
(CN2401) q; Screw (M1.7X3.5)
8Screw (M1.7X2.5)
qd Control switch block
(SS4720)
2-11.SE-139 BOARD, MIC UNIT

2-12
DCR-IP1/IP1E
2-12.LENS BLOCK ASSEMBLY
3Screw (M1.7X2.5)
5Two screws
(M1.7X2.5)
2
1FP-719 flexible board
(CN201)
4Joint
7FP-719 flexible board
(CN5003)
8CDP sheet
9CD sheet
q; CD sheet 2
6Lens block assembly
4
9CD heat sink
qa Lens frame
qd PF sheet
qs LF sheet 2
3Two screws (M1.7X2.5)
8Screw (M1.7X3.5)
2Flexible board
(CN5002) 1CD guard sheet 5Flexible board
(CN5001)
7CD-458 board
q; Screw (M1.7X3.5)
6CD guard sheet 2
2-13.CD-458 BOARD

2-13
DCR-IP1/IP1E
6Remove the cabinet G
direction of the arrow A.
1Screw (M1.7X2.5) 2Two screws (M1.7X2.5)
3
A
4Screw (M1.7X2.5)
5Three bosses
4IF frame
6Cabinet L assembly
3Screw (M1.7X2.5)
5Two screws (M1.7X2.5)
1IF sheet
2Two screws (M1.7X2.5)
2-14.CABINET G
2-15.CABINET L ASSEMBLY