Sony SSC-530AM User manual

SONY
Black
and
White
Video
Camera
SSC-530AM
Operating Instructions
Before
operating
the
unit,
please
read
this
manual
thoroughly
and
retain
it
for
future
reference.
Owner’s Record
The
model
and
serial
numbers
are
located
at
the
rear.
Record
the
serial
number
in
the
space
provided
below.
Refer
to
these
numbers
whenever
you
call
upon
your
Sony
dealer
regarding
this
product.
Model No. SSC-530AM Serial No.
AUTOMOTIVE
WatchCam
Sony
Corporation
©
1995
Printed
in
Japan
3-798-878-11 (1)
Features
The
SSC-530AM
is
a
black
and
white
video
camera
designed
for
fitting
to
a
bus
or
truck,
to
provide
the
driver
with
a
view
of
the
rear
of
the
vehicle.
It
should
be
used
together
with
a
black
and
white
monitor
such
as
the
Sony
SSM-721AMR.
It has the following main features:
* Compact and lightweight
*
Uses
a
CCD
(Charge
Coupled
Device)
image
sensor,
giving
a
high
resolution
picture.
*
Wide
field
of
view
—
100
degrees
horizontally,
80
degrees
vertically
*
Protected
by
a
water-resistant
casing,
so
it
can
be
used
even
where
exposed
to
rain,
snow
and
spray.
¢
Uses
a
4-pin
connector,
so
only
one
cable
is
needed
to
connect
to
a
monitor.
*
Operates
in
a
wide
temperature
range
(-20°C
to
+70°C;
—4°F
to
+158°F).
*
Built-in
electret
condenser
microphone
allows
aural
check.
Part Designations
Water-resistant
connecting cable
Water-resistant
casing
Microphone
Fixing holes
(five holes; 26.5 mm)
Camera bracket
4-pin connector

installation Example
Camera a Monitor
Attach with screws, using the five fixing
holes.
Rubber cap
(supplied)
Connecting cable
To protect it from water, apply self-fusing
tape (supplied) to the portion of the cable
which is in contact with the rubber cap.
Attaching the camera bracket to the camera
1 Using the four angle adjustment screws’, the 4
mm washers’, and the 3 mm Allen key”, attach
the camera bracket* to the camera loosely
enough for adjustment.
*: supplied
Angle adjustment screws
2 Adjust the camera angle, then tighten the
screws.
4 mm washers

rorelalarsatiare
mo
Miuelalivels
Example:
Connecting
to
the
SSM-
AMR
7-inch
black
and
white
monitor
To ensure adequate insulation,
wrap the cable connection with the
supplied self-fusing tape.
Align the groove and
the projection.
ad
fusing tape and wrap the
connection.
SSM-721AMR
black and white
monitor
(not supplied)
SSC-530AM
to CAMERA INPUT
(4-pin
connector)
:
=>
°
io)
o
CC)
>
Connecting
cable
Camera
cable
VK-310A/318A/320A
(water-resistant)
(not
supplied)
to
power
supply
The
camera
is
supplied
with
power
through
the
connecting
cable,
so
the
camera
power
is
automatically
turned
on
when
the
power
to
the
monitor
is
turned
on.
*
To
prevent
the
possibility
of
an
accident
caused
by
Ensure
that
the
cable
is
properly
protected
if it
has
a
short
circuit,
disconnect
the
ground
terminal
of
the
to
pass
through
the
engine
compartment.
vehicle
battery
before
installation.
*
When
washing
the
vehicle
with
a
pressure
hose,
*
Ensure
that
the
cable
is
connected
firmly.
be
sure
to
keep
the
nozzle
at
a
distance
of
at
least
Otherwise
there
may
be
problems,
such
as
a
poor
1
meter
from
the
camera.
picture,
or
total
failure
of
operation.

Cor eTal dale mUrciiare mavlelel- maleic
If the camera bracket is fastened directly to the 1 Enlarge the five holes in the vehicle body to
vehicle body, noise may appear in the picture on between 10.2 mm and 10.5 mm in diameter.
the monitor. In this case the camera bracket should
be mounted so that it is not in direct contact with 2 Insert the supplied rubber nuts into these holes.
the vehicle body, using the supplied rubber nuts.
3 Using 5 mm hexagon head.bolts (ISO, 20 mm
long) and 5 mm washers, fasten to a torque of
5 to 6 kg per cm.
Camera bracket
5 mm |SO bolts Rubber nuts (supplied)
(supplied)
Inside
Do not remove or even
loosen this screw.

Monitor
Attach with screws, using the five fixing
holes.
Rubber cap
(supplied)
Connecting cable
To protect it from water, apply self-fusing
tape (supplied) to the portion of the cable
which is in contact with the rubber cap.
Attaching the camera bracket to the camera
1 Using the four angle adjustment screws’, the 4
mm washers", and the 3 mm Allen key”, attach
the camera bracket* to the camera loosely
enough for adjustment.
*: supplied
Angle adjustment screws
2 Adjust the camera angle, then tighten the
screws.
4 mm washers