Sony SSC-M183 - CCTV Camera User manual

BLACK AND WHITE VIDEO CAMERA & COLOR VIDEO CAMERA
SSC-M183/M183CE
SSC-M188CE
SSC-M383/M383CE
SSC-M388CE
SSC-DC193/DC193P
SSC-DC198P
SSC-DC393/DC393P
SSC-DC398P
SERVICE MANUAL
1st Edition

SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

1
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 3
Related manuals......................................................................................................... 3
Trademarks ................................................................................................................ 3
1. Service Overview
1-1. Factory Default Setting of Switch...............................................................1-1
1-2. Board Location............................................................................................1-1
1-3. Installation/Removal of Cabinet .................................................................1-2
1-3-1. Top Cover...................................................................................1-2
1-3-2. Front Cover Assembly ...............................................................1-3
1-3-3. Bottom Cover .............................................................................1-3
1-4. Installation/Removal of Board ....................................................................1-5
1-4-1. R-2001 Board .............................................................................1-5
1-4-2. PB-2001/PC-2001 Board ...........................................................1-7
1-4-3. AC-24/230 Board .......................................................................1-9
1-5. CCD Assembly..........................................................................................1-11
1-6. Plate Reinforcement ..................................................................................1-12
2. Confirmation and Adjustment
2-1. Adjustment Tools and Required Equipment ...............................................2-1
2-1-1. Adjustment Tools and Required Equipment ..............................2-1
2-1-2. Connection Diagram ..................................................................2-2
2-1-3. Signal Measuring Connectors for Confirmation and
Adjustment .................................................................................2-2
2-1-4. Selection Flow of Required Items for Adjustments of 0 dB and
Color Reproduction .................................................................... 2-3
2-2. Confirmation ...............................................................................................2-3
2-2-1. Confirmation of 0 dB adjustment...............................................2-3
2-2-2. Confirmation of Color Reproduction Adjustment .....................2-4
2-3. Adjustment ..................................................................................................2-4
2-3-1. Adjustment Software..................................................................2-4
2-3-2. Preparation for Adjustment ........................................................2-5
2-3-3. Reading of Parameter .................................................................2-5
2-3-4. 0 dB Adjustment ........................................................................2-6
2-3-5. Color Reproduction Adjustment ................................................2-6
2-3-6. Writing .......................................................................................2-7
2-4. Correction of Residual Point Noise.............................................................2-7

2SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
3. Troubleshooting
3-1. Black and White Camera ............................................................................3-1
3-2. Color Camera ..............................................................................................3-4
4. Spare Parts
4-1. Notes on Repair Parts..................................................................................4-1
5. Block Diagrams
5-1. Color Camera ..............................................................................................5-2
Overall ....................................................................................................5-2
5-2. B/W Camera................................................................................................5-4
Overall ....................................................................................................5-4

3
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Manual Structure
Purpose of this manual This manual is the Service Manual of the Black and White Video Camera & Color
Video Camera SSC-M183/M183CE/M188CE/M383/M383CE/M388CE/DC193/
DC193P/DC198P/DC393/DC393P/DC398P.
This manual contains service overview, adjustment, troubleshooting, spare parts and
block diagrams.
Related manuals In addition to this Service Manual, the following manuals is provided.
..
..
.Operating Instructions (Supplied for products)
Part No.: 3-206-754-11
(For SSC-M183/M183CE/M188CE/M383/M383CE/M388CE)
Part No.: 3-206-753-11
(For SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P)
This manual describes the information required for the proper operation and
application of this unit.
Trademarks Trademarks and registered trademarks used in this manual are follows.
.Windows and Windows NT are registered trademarks of Microsoft Corporation.

1-1
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Section 1
Service Overview
2
3
4
5
1
2
3
4
1
1-1. Factory Default Setting of Switch
For SSC-DC193/DC193P/DC393/DC393P/M183/
M183CE/M383/M383CE
No. Description Factory default setting
1Auto iris lens selection switch DC
2Sync switch LL
3AGC ON/OFF switch AGC
4BLC ON/OFF switch OFF
5CCD-IRIS ON/OFF switch OFF
For SSC-DC198P/DC398P/M188CE/M388CE
No. Description Factory default setting
1Auto iris lens selection switch DC
2AGC ON/OFF switch AGC
3BLC ON/OFF switch OFF
4CCD-IRIS ON/OFF switch OFF
AC-230/24 board
F2001 board
R-2001 board
PB-2001/PC-2001 board
1-2. Board Location
Board name Use model
AC-230board SSC-M188CE/M388CE
SSC-DC198P/DC398P
AC-24 board SSC-M183
SSC-M183CE
SSC-M383
SSC-M383CE
SSC-DC193
SSC-DC193P
SSC-DC393
SSC-DC393P
PB-2001 board SSC-M183
SSC-M183CE
SSC-M188CE
SSC-M383
SSC-M383CE
SSC-M388CE
PC-2001 board SSC-DC193
SSC-DC193P
SSC-DC198P
SSC-DC393
SSC-DC393P
SSC-DC398P
F2001 Board Common use
R-2001 Board SSC-M183/M183CE/M383/M383CE
SSC-M188CE/M388CE
SSC-DC193/DC193P/DC393/DC393P
SSC-DC198P/DC398P

1-2 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
PTP 2x5
Camera
screw
Top cover
Top chassis
1-3. Installation/Removal of Cabinet
1-3-1. Top Cover
1. Remove the six screws, then remove the rear panel.
B 2x5
B 2x5
B 2x5
Rear panel
2. Remove the top cover in the direction indicated by the
arrow.
3. Remove the two screws, then remove the top chassis
and camera screw.
4. Attach the top cover in the reverse order of steps 1 to
3.

1-3
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
B 2x5
Flexible flat cable
Front cover assembly
Solder Lead wire
CN401
Portion A
F-2001 board
1-3-2. Front Cover Assembly
For SSC-M183/M183CE/M188CE/M383/M383CE/
M388CE
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the two screws.
3. Move portion A of the front cover assembly in the
direction indicated by the arrow, then remove the front
cover assembly.
4. Disconnect one flexible flat cable from the connector
(CN401) on the F-2001 board.
5. Remove one solder from the F-2001 board, then
disconnect one lead wire.
6. Attach the front cover assembly in the reverse order of
steps 1 to 5.
B 2x5
Lens connector
Flexible flat cable
Front cover assembly
Portion A
F-2001 board
CN401
For SSC-DC193/DC193P/DC198P/DC393/DC393P/
DC398P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the two screws.
3. Move portion A of the front cover assembly in the
direction indicated by the arrow, then remove the front
cover assembly.
4. Disconnect one flexible flat cable from the connector
(CN401) on the F-2001 board.
5. Attach the front cover assembly in the reverse order of
steps 1 to 4.
1-3-3. Bottom Cover
n
Be sure to attach the plate reinforcement in place.
For details on the installation of the plate reinforcement,
refer to Section 1-6.
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the two screws (B 2x5), then remove the rear
chassis assembly.

1-4 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
PTP 2x5
Camera screw
Bottom
chassis
Bottom cover
AC-230 board
B 2x5
B 2x5
B 2x5
B 2x5PB-2001/
PC-2001 board
Rear chassis assembly
For SSC-M188CE/M388CE/DC198P/DC398P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the two screws, then remove the rear chassis
assembly.
4. Remove one screw, then remove the PB-2001/PC-
2001 board from the bottom chassis. (Refer to Section
1-3-3.)
5. Remove one screw, then remove the AC-230 board
from the bottom chassis. (Refer to Section 1-4-3.)
6. Remove the two screws, then remove the bottom
chassis and camera screw from the bottom cover.
n
Before attaching the rear chassis assembly, securely attach
the AC-230 board.
7. Attach the bottom cover in the reverse order of steps 1
to 6.
PTP 2x5
Camera screw
Bottom
chassis
Plate
reinforcement
Bottom cover
B 2x5
B 2x5
B 2x5
B 2x5B 2x5
AC-24 board
PB-2001
/PC-2001 board
Rear chassis assembly
4. Remove one screw (B 2x5), then remove the PB-
2001/PC-2001 board from the bottom chassis. (Refer
to Section 1-3-3.)
5. Remove one screw (B 2x5), then remove the plate
reinforcement. (Refer to Section 1-6.)
6. Remove one screw (B 2x5), then remove the AC-24
board from the bottom chassis. (Refer to Section 1-4-
3.)
7. Remove the two screws (PTP 2x5), then remove the
bottom chassis and camera screw from the bottom
cover.
n
Before attaching the rear chassis assembly, securely attach
the AC-24 board.
8. Attach the bottom cover in the reverse order of steps 1
to 7.

1-5
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
AC-24 board
Solder
Harness
Harness
PB-2001/PC-2001 board
Solder
Rear chassis assembly
CN103
CN203 (PB-2001 board)
CN204 (PC-2001 board)
1-4. Installation/Removal of Board
1-4-1. R-2001 Board
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
5. Remove the AC-24 board from the bottom chassis.
(Refer to Section 1-3-3.)
6. Remove the solder from the connector (CN203/204)
on the PB-2001/PC-2001 board, then disconnect one
harness.
7. Remove the solder from the connector (CN103) on the
AC-24 board, then disconnect one harness.
B 2x5
BNC connector
Rear chassis
R-2001 board
Nut
Two solders
Toothed washer
Earth lug
8. Remove one screw and two solders, then remove the
R-2001 board.
9. Remove the nut, then remove the toothed washer, earth
lug and BNC connector from the rear chassis.
10. Attach the R-2001 board in the reverse order of steps 1
to 9.

1-6 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
B 2x5
BNC connector
Rear chassis
R-2001 board
Nut
Two solders
Toothed washer
Earth lug
8. Remove one screw and two solders, then remove the
R-2001 board.
9. Remove the nut, then remove the toothed washer, earth
lug and BNC connector from the rear chassis.
10. Attach the R-2001 board in the reverse order of steps 1
to 9.
AC-230 board
Solder
Harness
Harness
PB-2001/PC-2001 board
Solder
CN203 (PB-2001 board)
CN204 (PC-2001 board)
Rear chassis assembly
CN603
For SSC-M188CE/M388CE/DC198P/DC398P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
5. Remove the AC-230 board from the bottom chassis.
(Refer to Section 1-3-3.)
6. Remove the solder from the connector (CN203/204)
on the PB-2001/PC-2001 board, then disconnect one
harness.
7. Remove the solder from the connector (CN603) on the
AC-230 board, then disconnect one harness.

1-7
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
AC-24 board
Harness
PB-2001
/PC-2001 board
Solder
CN102
1-4-2. PB-2001/PC-2001 Board
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
Removal
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the plate reinforcement. (Refer to Section 1-
6.)
5. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
6. Remove the AC-24 board from the bottom chassis.
(Refer to Section 1-3-3.)
7. Remove the solder from the connector (CN102) on the
AC-24 board, then remove the PB-2001/PC-2001
board.
Marking
Bottom chassis
Bottom chassis
Groove
AC-24 board
Harness
PB-2001
/PC-2001 board
PB-2001
/PC-2001 board
Solder
CN102 Claw
Installation
1. Attach the AC-24 board in the reverse order of steps 6
and 7 of the Removal.
2. Insert the marking section of the PB-2001/PC-2001
board into the groove of the bottom chassis, then
attach in the direction indicated by the arrow.
3. Attach the PB-2001/PC-2001 board so that it is placed
outside of the claw of the bottom chassis.
4. Attach the PB-2001/PC-2001 board in the reverse
order of steps 1 to 3.

1-8 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Marking
Bottom chassis
Bottom chassis
Groove
AC-230 board
Harness
PB-2001
/PC-2001 board
PB-2001
/PC-2001 board
Solder
CN602 Claw
Installation
1. Attach the AC-230 board in the reverse order of steps
6 and 7 of the Removal.
2. Insert the marking section of the PB-2001/PC-2001
board into the groove of the bottom chassis, then
attach in the direction indicated by the arrow.
3. Attach the PB-2001/PC-2001 board so that it is placed
outside of the claw of the bottom chassis.
4. Attach the PB-2001/PC-2001 board in the reverse
order of steps 1 to 3.
AC-230 board
Harness
PB-2001
/PC-2001 board
Solder
CN602
For SSC-M188CE/M388CE/DC198P/DC398P
Removal
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the plate reinforcement. (Refer to Section 1-
6.)
5. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
6. Remove the AC-230 board from the bottom chassis.
(Refer to Section 1-3-3.)
7. Remove the solder from the connector (CN602) on the
AC-230 board, then remove the PB-2001/PC-2001
board.

1-9
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
AC-24 board
Harness
PB-2001
/PC-2001 board
Solder
CN102
1-4-3. AC-24/230 Board
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
Removal
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the plate reinforcement. (Refer to Section 1-
6.)
5. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
6. Remove the AC-24 board from the bottom chassis.
(Refer to Section 1-3-3.)
7. Remove the solder from the connector (CN102) on the
AC-24 board, then remove the AC-24 board.
Bottom chassis
Bottom chassis
Claw
B 2x5
AC-24 board
AC-24 board Marking Groove
Installation
1. Attach the AC-24 board in the reverse order of steps 5
and 6.
2. Insert the marking section of the AC-24 board into the
groove of the bottom chassis, then attach in the
direction indicated by the arrow.
3. Attach the AC-24 board so that it is placed outside of
the claw of the bottom chassis.
4. Attach the AC-24 board in the reverse order of steps 1
to 4.

1-10 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Bottom chassis
Bottom chassis
Claw
B 2x5
AC-230 board
AC-230 board Marking Groove
Installation
1. Attach the AC-230 board in the reverse order of steps
5 and 6.
2. Insert the marking section of the AC-230 board into
the groove of the bottom chassis, then attach in the
direction indicated by the arrow.
3. Attach the AC-230 board so that it is placed outside of
the claw of the bottom chassis.
4. Attach the AC-230 board in the reverse order of steps
1 to 4.
Harness
PB-2001
/PC-2001 board
Solder
CN602
AC-230 board
For SSC-M188CE/M388CE/DC198P/DC398P
Removal
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the PB-2001/PC-2001 board from the bottom
chassis. (Refer to Section 1-3-3.)
5. Remove the AC-230 board from the bottom chassis.
(Refer to Section 1-3-3.)
6. Remove the solder from the (CN602) connector on the
AC-230 board, then remove the AC-230 board.

1-11
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
B 2x5
CCD assembly
Plate
Slider
Guard plate
Spring
Front cover
assembly
1-5. CCD Assembly
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
n
When removing the screw of the retaining plate, be careful
of the spring between the front cover and the CCD cover
since it may pop up.
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the four screws (B 2x5) from the front cover
assembly, then remove the plate, guard plate, slider,
CCD cover and spring.
4. Remove the CCD assembly.
5. Attach the CCD assembly in the reverse order of steps
1 to 4.
B 2x5
CCD assembly
Plate
Slider
Guard plate
Spring
Front cover
assembly
For SSC-M188CE/M388CE/DC198P/DC398P
n
When removing the screw of the retaining plate, be careful
of the spring between the front cover and the CCD cover
since it may pop up.
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the four screws (B 2x5) from the front cover
assembly, then remove the plate, guard plate, slider,
CCD cover and spring.
4. Remove the CCD assembly.
5. Attach the CCD assembly in the reverse order of steps
1 to 4.

1-12 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
A
B
AC-24 board
DC/AC connector
Plate reinforcement
1-6. Plate Reinforcement
For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P
1. Remove the top cover. (Refer to Section 1-3-1.)
2. Remove the front cover assembly. (Refer to Section 1-
3-2.)
3. Remove the rear chassis assembly. (Refer to Section 1-
3-3.)
4. Remove the PB-2001 board. (Refer to Section 1-4-2.)
5. Remove one screw and slightly raise the DC/AC
connector on the AC-24 board in the direction
indicated by the arrow A, then remove the plate
reinforcement in the direction indicated by the arrow
B.
6. Attach the plate reinforcement in the reverse order of
steps 1 to 5.

2-1
SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
Section 2
Confirmation and Adjustment
n
The confirmation and adjustment described in this section
are intended only for the color models. In the B & W
models, confirmation and adjustment are not required.
2-1. Adjustment Tools and Required
Equipment
2-1-1. Adjustment Tools and Required
Equipment
J-6027-100-A Color Bar Chart (For PTB-700)
J-6020-250-A Color Bar Chart (For PTB-500)
J-6029-140-B Pattern Box PTB-500
J-6029-850-A Pattern Box PTB-700
..
..
.For the light source of test chart
J-6432-790-A Vectorscope Scale
WGC Y YI M g RB
..
..
.For the color reproduction adjustment
1J-6432-780-A Set of adjusting tool
2J-6432-780-3 Adjustment harness
3J-6432-780-4 Adjustment software
..
..
.For the color reproduction adjustment
This scale is printed on the rear cover paper.
B-Y
R-Y
MG
R
G
WB
CB
YL
B
CY
J-6432-790-A
NBC-2001
23
1
.Oscilloscope
.Digital voltmeter
.Vectorscope
.Waveform Monitor
.Color Monitor
.Personal computer
.RS-232C cable (Straight)
n
When you need an adjusting tool board, order 1
(J-6432-780-A).
(All the parts are included in 1.)

2-2 SSC-M183/M183CE/M188CE/M383/M383CE/M388CE
SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P
2-1-2. Connection Diagram 2-1-3. Signal Measuring Connectors for
Confirmation and Adjustment
The signal required for confirmation can be obtained from
the test pin of the PC-2001 board of this unit. The signal
required for adjustment can be obtained from the test pin
of the adjusting tool board.
TP1: CCD LEVEL
TP2: A/D IN
E1: GND
Adjusting tool board
PC-2001 board (Side B)
Pattern box
(PTB-700/500) CAMERA
Waveform Monitor
Set of adjusting tool
(J-6432-780-A)
Personal computer
PC-2001 board
CN205
VIDEO
OUT
CN1
Color Monitor
75 Ztermination
Vectorscope
RS-232C cable
(straight)
.DC12 V/AC24 V (60 Hz)
SSC-DC193/DC393
.DC12 V/AC24 V (50 Hz)
SSC-DC193P/DC393P
.AC220 to 240 V (50 Hz)
SSC-DC198P/DC398P
E1
CN2
CN1
TP2
TP1
CN203 CN205
CL201CL202
CT301