Sony XCL-U1000 User manual

30 XCL-U1000/U1000C
Digital Video Camera
Intelligent
XCI
XC (Non-TV Format)
Analog Video Camera
XC (TV Format)
Accessories
XCD XCLXCG
Color Camera Module
Color PTZ Camera
FCBEVI
Connection Diagram
P56
DIGITAL VIDEO CAMERA MODULE
XCL-U1000 (B/W)
XCL-U1000C (Color)
26
56
8713
44
103
958
4-M3 depth 4
4-M3 depth 4
26
5013
Outline
Compact camera adaptor■
DC-700/700CE•
12-pin camera cable (CE standard)■
CCXC-12P02N (2 m)•
CCXC-12P05N (5 m)•
CCXC-12P10N (10 m)•
CCXC-12P25N (25 m)•
Tripod adaptor■
VCT-ST70I•
Accessories
Dimensions
The XCL-U1000 and XCL-U1000C are vibration-resistant
video camera modules equipped with digital video interface
that output image data using the LVDS signal. These black/
white and color models are housed in a same body.
The adoption of a compact Camera Link connector enables
the image digital output at 15 fps.
Features
1/1.8-type PS CCD with square pixels■
UXGA image (1,600 × 1,200 pixels) captures video at 15 fps■
Readout mode: Normal/Binning (XCL-U1000 only)■
Shutter: Normal/External trigger shutter■
Monitor output■
White balance (XCL-U1000C only)■
Auto/Manual/Preset selectable•
Matrix function for accurate color reproduction■
(XCL-U1000C only)
High shock and vibration resistance■
C-mount lens■
RS-232C Control■
High sensitivity■
XCL-U1000 : 400 lx at F 5.6•
XCL-U1000C : 2,000 lx at F8•
Digital output Camera Link (non-PoCL)■
XCL-U1000 : 10 bit•
XCL-U1000C : RGB 24 bits•
*1 : XCL-U1000
*2 : XCL-U1000C
Partial
Scan
C
Lens Mount
CL
Output
1.18 Type
CCD
UXGA
Output
Normal
Shutter
RS232C
Control
Manual
White
Balance
Fixed
White
Balance
One-Push
White
Balance
*2 *2 *2
*2*1
B/W RGB
LUT
Reversal
Nega
Posi
External
Trigger
Shutter
Progressive
Scan
Long
Exposure
Long
Exposure
Squ are
Pixels
Unit: mm

31
XCL-U1000/U1000C
Digital Video Camera Intelligent
XCI XC (Non-TV Format)
Analog Video Camera
XC (TV Format) Accessories
XCL XCDXCG
Color Camera Module
Color PTZ Camera
FCB EVI
400
0
0.2
0.4
0.6
0.8
1. 0
500 600 700 800 900 1000
0
0.2
0.4
0.6
0.8
1. 0
400
BGR
450 500 550 600 650 700
Spectral Sensitivity Characteristics
Relative sensitivity
Wavelength (nm)
(Lens characteristics and light source characteristics excluded.)
(Typical Values)
XCL-U1000•
Relative sensitivity
Wavelength (nm)
(Typical Values)
XCL-U1000C•
(Lens characteristics and light source characteristics excluded.)
Specifications
XCL-U1000 XCL-U1000C
Camera
Image type B/W Color
Image sensor 1/1.8-type Progressive scan IT CCD
Number of effective pixels (H) × (V) 1,628 × 1,236
Cell size (H) × (V) 4.4 m × 4.4 m
Standard output pixels (H) × (V) 1,600 × 1,200
Color lter — Color mosaic
Frame rate 15 fps
Minimum illumination 2 lx (Iris: F1.4, Gain: 18 dB, Shutter: 1/15 s) 4 lx (Iris: F1.4, Gain: 18 dB, Shutter: 1/15 s)
Sensitivity F5.6 (400 lx, Gain: 0 dB) F8 (2000 lx, Gain: 0 dB)
SNR 1 step (Lens close, Gain: 0 dB, 8 bits)
Gain Manual: 0 dB to 18 dB
Shutter speed (Normal) 2 sec to 1/10,000 sec
White balance — Pre-set, Manual, One Push, AWB
Reference video output level 940 steps 235 steps
Reference pedestal level 64 steps 16 steps
Output signal frequency 15 Hz (Normal mode)
Monitor output (analog output) Reference video output level: 700 mV, HD frequency: 75 kHz positive, VD frequency: 60 Hz positive
Camera Features
Readout modes Normal, Binning (1 × 2), Partial scan Normal/Partial scan
Readout features Binarization, Gamma (arbitrary setting), Gray scale Binarization, Gamma (arbitrary setting), Color bar feature
Synchronization Hardware trigger
Trigger modes Edge Detection, Exposure time setting by trigger width
External trigger shutter speed Edge detection mode: 1/15 sec to 1/10,000 sec Trigger Width: 1 sec to 1/10,000 sec
Partial scanning OFF/ON (Vertical 1/16 V to 15/16 V)
Detail OFF/ON
Color matrix — OFF/ON
Interface
Video data output 10 bit, digital 24 bit, RGB Color, digital
Digital interface LVDS
Camera specication non-PoCL, Base Conguration, CameraLink®Version 1.0
Output data clock 36 MHz
General
Lens mount C-mount
Flange focal length 17.526 mm
Power requirements DC +12 V (10.5 V to 15.0 V)
Power consumption 5.5 W
Operating temperature –5°C to +45°C
Performance guarantee temperature 0°C to 40°C
Storage temperature –30°C to +60°C
Operating humidity 20% to 80% (no condensation)
Storage humidity 20% to 95% (no condensation)
Vibration resistance 10 G (20 Hz to 200 Hz)
Shock resistance 70 G
Dimensions (W × H × D) 56 × 44 × 95 mm (not including projecting parts)
Mass 250 g
MTBF 49,059 hours (Approx. 5.6 years)
Regulations UL60950-1+CSA C22.2 No60950, FCC/ICES-003: Class A, CE: EN61326, AS/NZ: EN61326, VCCI: FCC Class A, KC: KN22/KN24: Class A
Supplied accessories Lens mount cap (1), Operating Instructions (1)

32 XCL-U1000/U1000C
Digital Video Camera
Intelligent
XCI
XC (Non-TV Format)
Analog Video Camera
XC (TV Format)
Accessories
XCD XCLXCG
Color Camera Module
Color PTZ Camera
FCBEVI
1RS-232C connector (6-pin)
You can connect a senal cable to this connector to control a
camera module from a camera control device.
2Monitor output connector (15-pin)
You can connect a monitor cable to this connector to display an
image on a multiscan monitor supporting UXGA resolution.
Note
If you connect a multiscan monitor that does not support UXGA
resolution, an image may not be displayed.
3DC IN (DC power input) connector (12-pin)
You can connect a CCXC-12P05N camera cable to input the
+12 V DC power supply. The pin conguration of this connector is
as follows.
4DIGITAL IF (Interface) connector (26-pin)
You can connect a digital interface cable to this connector to
control a camera module from a host device utilizing the serial
communication protocol while outputting a video signal from the
camera module. You can input the external trigger signal via the
26-pin connector and operate a camera module in the external
trigger mode. The pin conguration of this connector is as
follows.
Note
When operating a camera module by inputting an external
trigger signal via the 26-pin connector, be careful about trigger
pulse input specications (DIGITAL IF terminal).
1Lens mount (C-mount)
Attach any C-mount lens or other optical equipment.
Note
The lens must not project more than 10 mm from the lens mount.
2Reference screw holes (at the top)
3Reference screw holes/Tripod screw holes (at the bottom)
These precision screw holes are for locking the camera module.
Locking the camera module into these holes secures the optical
axis alignment.
You can install the camera on a tripod. To install on a tripod, you
will need to install a tripod adaptor VCT-ST70I to the camera on
the reference holes.
Pin No. Signal Pin No. Signal
1 TXD 4 NC
2 RXD 5 NC
3 Ground 6 NC
Pin No. Signal Pin No. Signal
1 R output 9 NC
2 G output 10 Ground
3 B output 11 NC
4NC 12NC
5 Ground 13 HD output
6 Ground 14 VD output
7 Ground 15 NC
8 Ground
Pin No. Signal Pin No. Signal
1 Ground 7 NC
2 +12 V DC 8 Ground
3 Ground 9 NC
4 NC 10 Exposure pulse output
5 Ground 11 Trigger pulse input
6 NC 12 Ground
Pin No. Digital signal Pin No. Digital signal
1 INNER_SHIELD (Ground) 14 INNER_SHIELD (Ground)
2 X0– (Output) 15 X0+ (Output)
3 X1– (Output) 16 X1+ (Output)
4 X2– (Output) 17 X2+ (Output)
5 XCLK– (Output) 18 XCLK+ (Output)
6 X3– (Output) 19 X3+ (Output)
7 Ser TC+ (Input) 20 Ser TC– (Input)
8 Ser TFG– (Output) 21 Ser TFG+ (Output)
9 TRIG– (Input) 22 TRIG+ (Input)
10 NC 23 NC
11 NC 24 NC
12 NC 25 NC
13 INNER_SHIELD (Ground) 26 INNER_SHIELD (Ground)
61 54321
10 9876
15 14 13 12 11
43
25
12
34
1Lens mount (C-mount)
2Reference screw holes
(at the top)
3Reference screw holes/
Tripod screw holes
(at the bottom)
Rear Panel
Location and Function of Parts and Controls
Connector Pin Assignments
Lens mount shoulder
10 mm or less
1RS-232C connector (6-pin)
2Monitor output connector (15-pin)
4DIGITAL IF (Interface) connector (26-pin)
3DC IN (DC power input) connector (12-pin)

33
XCL-U1000/U1000C
Digital Video Camera Intelligent
XCI XC (Non-TV Format)
Analog Video Camera
XC (TV Format) Accessories
XCL XCDXCG
Color Camera Module
Color PTZ Camera
FCB EVI
DIGITAL IF terminal
When operating a camera module by inputting an external trigger
signal via the 26-pin connector, be sure to input trigger signals that
satisfy the following specications to both of the two terminals.
Trigger signal specications (conditions)
Amplitude: LVDS (output by the 3.3 volt IC)
Connection: Input a TRIG (–) signal to the 9th pin
Input a TRIG (+) signal to the 22nd pin
Connecting the Cables
1
2
3
4
5
6
7
98
1DC IN connector 2Digital interface connector
3Camera cable 4Digital interface cable
5Fastening screws 6Serial cable
7Monitor cable 8Monitor output connector
9RS-232C connector
Connect the camera cable to the DC IN connector and the digital
interface cable to the digital interface cable respectively. Also, if
needed, connect the monitor cable to the monitor output connector
and the serial cable to the RS-232C connector respectively. When
you connect the digital interface cable or monitor cable, turn the two
fastening screws on the connector to secure the cable tightly.
Connect the other end of the camera cable to the DC-700/700CE
and the other end of the digital interface cable to the camera module
interface board. Also, if needed, connect the other end of the monitor
cable to the monitor and the other end of the serial cable to the
camera control device.
You can control the camera from host device such as a PC.
The following table shows the control functions.
You can send a command corresponding to the control items, with
parameters for the desired settings, if necessary, from the host
device to control the camera.
About the Camera Control Method
Note
Make sure to supply power to the camera module and conrm that
the camera module is operating before inputting a trigger signal.
If you input external signals to a camera module without the power
supplied, this may cause a malfunction of the camera module.
Trigger Pulse Input Specifications
DC IN terminal
(When positive pole is set)
(When negative pole is set)
4.5 V to 5.0 V
0 V to 0.5 V
100 µs to 1 sec
4.5 V to 5.0 V
0 V to 0.5 V
100 µs to 1 sec
• Input impedance: 10 kΩ or more
Polarity: positive
Exposure Output Specifications (DC IN terminal only)
• When terminated at 10 kΩ or more
Exposure output is output as a pulse that indicates exposure time
when trigger mode is selected.
4.0 V to 4.5 V
0 V to 0.5 V
Exposure time
Control functions Description
XCL-U1000 XCL-U1000C
Operating mode Normal/Trigger
Shutter
speed
Normal 1 sec to 1/10000 sec
Trigger Edge Internal setting: 1/15 sec to 1/10000 sec
Trigger pulse width Setting by trigger pulse width
Gain 0 dB to 18 dB
Binning function OFF/ON −
Partial Scan function OFF/ON
Detail OFF/ON
External trigger input 26-pin connector / 12-pin connector
White balance −
Preset
Manual
One push (auto)
Color Matrix − OFF/ON