Sony VPCB1 Series Guide

VPCB1 Series Optical Disk Drive
Replacement Instructions
P/N 989201344 Rev B
1/3
Prepare the Computer.
CAUTION: Make sure the
computer is turned off, the lid is
closed, and the AC Adapter is
disconnected. Failure to do so can
result in damage to the computer.
Step 1. Place the computer upside
down on a protected surface with the
front edge facing you.
Battery Pack Removal
Step 2.
1)
Slide the left battery tab to the
unlock position.
2) With your right thumb, slide the
right battery tab to the left and hold.
3) Lift the battery with your left thumb
using the notch at the bottom to
remove.
Optical Drive Removal
(Steps 3-6)
Step 3. The Optical Disk Drive (ODD)
is located on the left side of the unit
as shown.
These easy instructions are intended to guide you through the replacement process.
Before you begin, place your notebook computer on a clean or covered surface to avoid
damage to the computer's case.*
ollow the ESD (Electrostatic Discharge) damage prevention instructions:
oHold parts by the edges, away from exposed circuitry when possible.
oDo not walk around excessively as this promotes static build-up.
Before you begin, remove any jewelry you may be wearing to prevent scratches to the surface
of your notebook computer.*
The appearance of the electronic components shown in the illustrations may be different from
the components shipped. This slight difference does not affect the accuracy of these
instructions.
* Sony is not responsible for damage caused by incorrect handling of the notebook computer.
IMPORTANT!
PLEASE READ BEFORE YOU START
1
.
3
.
2
.
Lift to remove

VPCB1 Series Optical Disk Drive
Replacement Instructions
P/N 989201344 Rev B
2/3
(Look for the screw hole with 3 dots)
Step 4. Using the enclosed magnetic
screwdriver, remove the one (1) screw
securing the ODD Bay. Put aside the
ODD Bay screws to re-secure the
ODD Bay later in the procedure.
Step 5. Insert your fingers in the space
between the ODD and the unit . Gently
pull towards the left to remove the
ODD.
Step 6. Carefully remove the ODD
assembly from the unit.
ODD Disassembly (Steps 7
-
9)
Step 7. Identify the two (2) side screws
that secure the ODD brackets to the
ODD.
Step 8. Remove the screws & bracket.
Put the ODD Brackets and screws
aside for transfer to the new ODD.
Step 9
.
Arrange the brackets &
screws as shown above. Set the old
ODD aside.
Step 11. Align the tabs on the bezel
with the tab holes located on the
ODD. Carefully press the bezel into
place.
O
DD Assembly (Steps 10
-
13)
Step 10. Take the new ODD and bezel
provided in the CRU kit and prepare for
assembly.
NOTE:
Identify tabs on the bezel and
tab holes located on the ODD.

VPCB1 Series Optical Disk Drive
Replacement Instructions
P/N 989201344 Rev B
3/3
Step 13. Position the new ODD (Label
side down) with brackets and screws as
shown.
Step 13. Using the ODD Screws, install
the ODD Brackets onto the new ODD.
Note:
Flat surface of bracket should
sit flush with silver side of ODD.
.
.
Step 15. Make sure the new ODD is
seated flush on the edge of the
computer.
Step 16. Reinstall the one (1) ODD
Bay screw to secure the ODD Drive
Bay.
.
ODD Installation (Steps 14-16)
Step 14. Align the ODD assembly
properly (label side down) and slide into
the computer.
Step 17
.
Reinstall the battery pack and
AC Adaptor.
Return the old ODD to Sony
following the included
shipping instructions.