Sony CDP-590 User manual

SERVICE MANUAL US Model
AEP Model
EModel
Australian Mode!
nCOMPACT
(flog®
DIGITAL AUDIO
SPECIFICATIONS
Compact disc player
Frequency response
Signal to noise ratio
Dynamic range
Harmonic distortion
Channel separation
Outputs
LINE OUT
(phono jacks)
PHONES
(stereo phone jack)
General
Power requirements
Power consumption
Dimensions
(approx., including
projections)
Weight (approx.)
Supplied accessories
Audio cord
Remote commander
R6 (size AA) batteries
MICROFILM
2Hz -20 kHz ±0.5 dB
More than 100 dB
More than 92 dB
Less than 0.008%
More than 95 dB
Output level 2V(at 50 kilohms)
Load impedance over 10kilohms
Output level max. 10mW
Load impedance 32 ohms
120 VAC, 60Hz
11W
430 X100 X280 mm (w/h/d)
(17X4X1 17. inches)
3.5 kg (7 lbs 12oz)
1(2 phono plugs -2phono plugs)
1
2
Remote commander
Remote control system
Power requirements
Dimensions
Weight
Infrared control
3VDC with two R6 (size AA) batteries
Approx. 43 X20 X175 mm (w/h/d)
(VAX'VisX 7inches)
Approx. 105 g(4 oz)
Including batteries
Design and specifications subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ^OR DOTTED
LINE WITH MARK ^ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
ALA SECURITE!
LES COMPOSANTS IDENTIFIES PAR UNE MARQUE ^
SUR LES DIAGRAMMES SCHEMATIQUES ET LA LISTE
DES PIECES SONT CRITIQUES POUR LA SECURITE
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIECES SONY DONT LES
NUMEROS SONT DONNES DANS CE MANUEL OU
DANS LES SUPPLEMENTS PUBLIES PAR SONY.
COMPACT DISC PLAYER

CDP-590
TABLE OF CONTENS
Section Title Page
Specifications 1
1. GENERAL 4
2. 1C FUNCTION DESCRIPTION 5
3. DISASSEMBLY OF BASE UNIT 6
4. ADJUSTMENTS 7
5. DIAGRAMS 11
5-1. Waveforms 11
5-2. Printed Wiring Boards 12
5-3. Schematic Diagram 15
5-
4. IC Block Diagrams 19
6. EXPLODED VIEWS 21
6-
1. Cabinet Section 21
6-2. Front Panel Section 22
63. MD Section 1(CDM 14-5BD1) 23
6-4. MD Section-2(BU-5BDl) 24
7. ELECTRICAL PARTS LIST 25
SAFETY CHECK-OUT
After correcting the original service problem,
perform the following safety check before releasing
the set to the customer:
Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for
AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to
earth ground and from all exposed metal parts to any
exposed metal part having areturn to chassis, must
not exceed 0.5 mA (500 microampers). Leakage
current can be measured by any one of three
methods.
1.Acommercial leakage tester, such as the
Simpson 229 or RCA WT-540A. Follow the
manufacturers’ instructions to use these instru-
ments.
2. Abattery-operated AC miliiammeter. The Data
Precision 245 digital multimeter is suitable for
this job.
3.
Measuring the voltage drop across aresistor by
means of aVOM or battery-operated AC volt-
meter. The “limit” indication is 0.75 V, so
analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa
SH-63Trd are examples of apassive VOM that
is suitable. Nearly all battery operated digital
multimeters that have a2V AC range are
suitable. (See Fig. A)
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-
UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may
suffer electrostatic breakdown because of the poten-
tial difference generated by the charged electrostatic
load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-
down and also use the procedure in the printed
matter which is included in the repair parts.
The flexible board is easily damaged and should be
handled with care.
CAUTION
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be
focused on the disc reflective surface by the objective
lens in the optical pick-up block. Therefore, when check-
ing the laser diode emission, observe from more than 30
cm away from the objective lens.
-2-

CDP-590
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
1.Laser Diode Properties
•Material: GaAlAs
•Wavelength: 780 nm
•Emission Duration: continuous
•Laser Output: max. 44.6 /iW*
*This output is the value measured at adistance of
about 200 mm from the objective lens surface on
the Optical Pick-up Block.
2. During service, do not take the Optical Pick-up
Block apart, and do not adjust the APC circuit.
If there is abreakdown in the APC circuit (includ-
ing laser diode), replace the entire Optiocal Pick-
up Block (including APC borad).
This set employs alaser. Therefore, be sure to fol-
low carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
BESKYTTELSE AF 0JNE MOD LASERSTRALING UNDER SERVICE
Idette apparat anvendes laserlys. Derfor skal
nedenst&ende instruktioner noje folges under service.
Folg ievrigt instruktionerne iservicemanualen.
ADVARSEL!!
Under service mA ojnene ikke komme naer objektiv-linsen
pA den optiske pick-up enhed. Itilfaelde af at det er
nodvendigt at kontrollere udsendelsen af laserlys, skal
det ske ien afstand af mere end 25 cm fra den optiske
pick-up.
1.Laser-didoe data
•Materiale: GaAlAs
•Belgelaengde: 780 nm
•UdstrMing: Kontinuerlig
•Laseroutput: Max. 0,4 mW*
*Malt i1,6 mm afstand fra overfladen af objektiv-
linsen pa den optiske pick-up enhed.
•Klassifikation: Klasse IHb.
2. Adskil aldrig den optiske pick-up enhed under
service, og juster ikke APC kredslobet (Automatic
Power Control). Hvis APC kredslobet (incl. laser-
dioden) bryder ned, skal hele den optiske pick-up
enhed (inch APC printkortet) udskiftes.
-3-

CDP-590
SECTION 1
GENERAL

SECTION 2
1C FUNCTION DESCRIPTION SECTION 3
DISSASSEMBLY OF BASE UNIT
IC101 (CXA1372Q) PIN DESIGNATION
Pin No. Pin Name I/O Pin Description
1VC GND when two (±) dual power supplies are in use, or the center voltage (2.5 V)
when asingle power supply is in use.
2FGD ITime constants for gain switching in normal mode/down mode and for focus gain are
3FS3 Iconnected between the FGD and FS3 pins.
4FLB IThe capacitor for low frequency boost in the focus servo loop is connected.
5FEO 0Focus drive output
6FE —IInverted input to focus amplifier
7SRCH ITime constants to generate the focus search waveform are connected.
8TGU ITime constants for gain switching in normal mode/up mode and for tracking gain are
9TG2 Iconnected between TGU pin and TG2 pin.
10 AVCC Analog power supply (5 Vwhen ±dual power supplies are in use, 5Vwhen asingle
power supply is in use.)
11 TAO 0Tracking drive output
12 TA- IInverted input to tracking amplifier
13 SL +INon- inverted input to sled amplifier
14 SLO 0Sled drive output
15 SL -INon-inverted input to sled amplifier
16 ESET IThe 610- kQ phase compensator resistor is connected to this pin.
17 ISET IThe current setting resistor is connected to this pin.
18 SSTOP IThe limit switch is connected to this pin.
19 AVEE Analog power supply (-5V when ±dual power supplies are in use, or GND when asingle
power supply is in use.)
20 DIRC IDirect control pin.
21 LOCK ISled run- away prevention circuit operates when this signal is “L".
22 CLK ISerial data transfer clock input that is supplied from CPU (or DSP).
23 XLT ILatch input from CPU (or DSP).
24 DATA ISerial data input from CPU (or DSP).
25 XRST ISystem reset. "V to reset.
26 C.OUT 0Output to tracking counter.
27 SENS 0SENS output
28 DGND Digital ground (GND). (GND when ±dual power supplies are in use. GND when asingle
power supply is in use.)
29 MIRR 0Mirror output.
30 DFCT 0Defect output. *TT when defective.
31 ASY IAuto-assymmetry control input.
32 EFM 0EFM comparator output.
33 FOK 0Focus OK
34 CC2 IDefect- bottom- hold input (input by capacitive coupling).
35 CC1 0Defect-bottom -hold output
36 DVCC Digital power supply (+5 Vwhen ±dual power supplies in use. +5 Vwhen asingle
power supply is in use.)
37 CB IThe defect- bottom- hold capacitor is connected to this pin.
38 CP IThe mirror hold capacitor is connected to this pin.
39 RF1 IRF signal input (input by capacitive coupling).
40 RFO IRF signal input (input by DC coupling).
41 DVEE Digital power supply (-5 Vwhen ±dual power supplis are in use. GND when asingle
power supply is in use.)
42 TZC ITracking zero cross comparator input.
43 TE ITracking error input.
44 TDFCT IThe defect prevention hold capacitor is connected to this pin.
45 ATSC IAnti-shock input.
46 FZC IFocus zero- cross comparator input.
47 FE IFocus error input.
48 FDFCT IThe defect prevention hold capacitor is connected to this pin.
Note:
Follow the disassembly procedure in the nomerical
order given.
OTurn the cam to the direction of arrow (Counter
clock wise) by minus screw driver.
QTake off the disc table.
©Remove the bracket yoke.
©Remove the MD (BU-5BD1) to the direction of arrow.
ELECT
1. Perfo
2. Use 1
wise
3. Use t
RF LE
This
Optical
Procedr
1. Conn
TP f
2. Turn
3. Put t
4. Confi
Optir
clear
RF L
E-F Bi
This
Optical
Procedi
1. Conr
and '
2. Grot
3. Turr
-5- -6-

SECTION 3
DISASSEMBLY OF BASE UNIT
Note:
Follow the disassembly procedure in the nomerical
order given.
oTurn the cam to the direction of arrow (Counter
clock wise) by minus screw driver.
©Take off the disc table.
©Remove the bracket yoke.
©Remove the MD (BU-5BD1) to the direction of arrow.
6-
SECTION 4
ADJUSTMENTS
ELECTRICAL ADJUSTMENTS
1. Perform adjustments in the order given.
2. Use YEDS-18 (Part No. 3-702-101-01) disc unless other-
wise indicated.
3. Use the oscilloscope with more than 10MQ impedance.
RF LEVEL check
This adjustment should be made after replacing the
Optical Pick-up Block.
Procedure:
oscilloscope
(DC range)
BD board
TP (RF) o
TP (VC) o
1. Connect oscilloscope to the test points TP (RF) and
TP (VC).
2. Turn POWER switch on.
3. Put the disc (YEDS-18) in and press >button.
4. Confirm that an optimum waveform eye pattern.
Optimum eye pattern means that shape “O’' can be
clearly distinguished at the center of the waveform.
RF LEVEL VOLT/DIV :200mV
TIME/DIV :500nS
A
A—l.2±0.3Vp-p
E-F Balance Check
This adjustment should be made after replacing the
Optical Pick-up Block.
Procedure:
oscilloscope
(DC range)
BD board
TP (TEO)
TP (VC)
1. Connect the oscilloscope to the test points TP (TEO)
and TP (VC).
2. Ground TP (ADJ), TP (TES).
3. Turn POWER switch on.
4. Put the disc (YEDS-18) in and press >button.
5. Confirm that the traverse waveform is symmetrical
above and below.
6. After adjustment, remove the TP(ADJ), TP(TES) in
ground.
NOTE :Take sweep time as long as
possible to obtain best waveform.
O’ 0,5»
A~ BA=B
VOLT/DIV :IV
TIME/DIV: 1ms
RF PLL Free-run Frequency Check
Procedure:
frequency counter
main board
TP (PCK)
1. Connect the frequency counter to the test points
TP (PCK) and TP (GND).
2. Turn POWER switch on.
3. Put the disc (YEDS-18) in and press >button.
4. Confirm that the reading on the frequency counter
is locked at 4.3218 MHz.
Focus/Tracking Gain Adjustment
Afrequency response analyzer is necessary in order
to perform this adjustment exactly.
However, this gain has amargine, so even if it is
slightly off, there is no problem. Therefore, this adjust-
ment is not recomended generally to be performed.
Focus/tracking gains determine the pick-up follow-up
(vertical and horizontal) relative to mechanical noise
and mechanical shock when the 2-axis device operate.
However, as these reciprocate, the adjustment is at
the point where both are satisfied.
•When gain is raised, the noise when the 2-axis
device operates increases.
•When gain is lowered, it is more susceptible to
mechanical shock and skipping occurs more easily.
•When gain adjustment is off, the symptoms below
appear.
Symptom
•The tim
becomes
->PU
selection
pressed,
about 2
•Music d
disc con
STOP -
matic s
buttons ]
Sound is
PLAY,
display s
•More n
device o
The folio1
Simple i
Note: Sinc«
positl
If thj
diffei
Procedun
1. Keep tl
If the s
perforn
2. Insert t
3. Connec
4. Adjustr
in the t
-7-

SECTION 4
DJUSTMENTS
1
4. Put the disc (YEDS-18) in and press >button.
5. Confirm that the traverse waveform is symmetrical
2ss other- above and below.
6. After adjustment, remove the TP(ADJ), TP(TES) in
ipedance. ground.
NOTE:Take sweep time as long as
possible to obtain best waveform.
\
A=B A-B
VOLT/DIV:IV
TIME/DIV: 1ms
Gain
Symptoms Focus Tracking
•The time until music starts
becomes longer for STOP
>PLAY or automatic
selection (mbuttons)
pressed. (Normally takes
about 2seconds.)
low low or high
•Music does not start and
disc continues to rotate for
STOP -*• >PLAY or auto-
matic selection (
m
buttons pressed.)
—low
•Sound is interrupted during
PLAY. Or time counter
display stops progressing.
—low
•More noise during 2-axis
device operation. high high
RF PLL Free-run Frequency Check
'RF) and
Procedure:
frequency counter
pattern. main board
can be tpIpckT
eform.
:200mV
:500nS
1. Connect the frequency counter to the test points
TP (PCK) and TP (GND).
2. Turn POWER switch on.
3. Put the disc (YEDS-18) in and press >button.
4. Confirm that the reading on the frequency counter
is locked at 4.3218 MHz.
Focus/Tracking Gain Adjustment
Afrequency response analyzer is necessary in order
cing the to Per^orm this adjustment exactly.
However, this gain has amargine, so even if it is
slightly off, there is no problem. Therefore, this adjust-
ment is not recomended generally to be performed.
Focus/tracking gains determine the pick-up follow-up
(vertical and horizontal) relative to mechanical noise
and mechanical shock when the 2-axis device operate.
However, as these reciprocate, the adjustment is at
the point where both are satisfied.
•When gain is raised, the noise when the 2-axis
device operates increases.
P(TEO) •When gain is lowered, it is more susceptible to
mechanical shock and skipping occurs more easily.
•When gain adjustment is off, the symptoms below
appear.
The following is asimple adjustment method.
Simple Adjustment
Note: Since exact adjustment cannot be performed, remember the
positions of the controls before performing the adjustment.
If the positions after the simple adjustment are only alittle
different, return the controls to the original position.
Procedure:
oscilloscope
(DC range)
BD board
TP (FEO)
TP (TEO)
TP (VC)
1. Keep the set flat.
If the set is not horizontal, this adjustment cannot be
performed due to the gravity against the 2axis device,
2. Insert the disc (YEDS-18) and press >PLAY button.
3. Connect the oscilloscope to TP (FEO) and TP (VC).
4. Adjustment RV102 so that the waveform is as shown
in the picture below, (focus gain adjustment)
VOLT/DIV: lOOmV
TIME/DIV: 2mS 1
-lOOmV
-OV
-7--8
5. Connect the oscilloscope to BD BOARD, TP (TEO).
6. Adjust RV101 so that the waveform is as shown in
the picture below, (tracking gain adjustment)
•Incorrect Examples (fundamental wave appears)
•Adjustment Location :
MAIN BOARD (Component side)
high tracking gain
(higher frequency of the fundamental wave than above)

3-

56 7 r8910 11 12 13 14 15 16 17 18 19 20 21 22
parts extracted from the component side,
parts mounted on the conductor side.
Through hole.
Pattern on the side which is seen.
Pattern of the rear side.
>Semiconductor Locations
PEAK
INDEX Li| d
MIN [STEP SEC
AUTO OHO lO O
SPACE urn
46 EDIT 12 3 45
54 rA-
60 Q O
90 1J678910
TIME 1
1
12 13 14 15
rFADE "I
16 17 18 19 20
Ref. No. Location Ref. No. Location
DIOI H-3 ICIOI 1-2
D201 F-9 IC102 H-2
D202 F-8 IC103 H-2
D203 F-8 IC201 G-8
D204 F-9 IC202 G-IO
D205 F-9 IC301 H-6
D208 G-8 IC302 F-6
D209 J-9 IC303 F-6
D301 F-8 IC304 E-7
D302 F-7 IC305 E-6
D401 1-14 IC306 C-6
D402 1-15 IC401 H-1
3
D403 1-15 IC451 J-22
D404 1-15
D405 1-15 QIOI J-2
D406 1-15 Q201 G-8
D407 1-14 Q202 H-8
D408 1-14 Q203 G-9
D409 1-14 Q204 G-9
D41
0
G-1
1
Q206 G-9
(—n1S425 S4
B«234irr^ 'S427 wmm
{check] el\ clear m-\ [>12] n
jW^bi
S40t®tF^^ ^S4lT^ii j
Vo .9
*-
I%X R50I
m'
g4g) -' 3^
0
[POWER SW BOARD]
J
I®
-13- -14-

5-3. SCHEMATIC DIAGRAM
l|2|3|4|5|6|7[ 8|
A
B
C
D
E
F
G
H
I
J
K
L
IV
o
[BD BOARD!
-15

17 |18 119 |20 |21 122 |23 |24
Note:
•All capacitors are in ijlF unless otherwise noted. pF: h/jlF
50WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in 17 and '/4Wor less unless otherwise
specified.
•%:indicates tolerance.
•A:internal component.
Note:
The components identi-
fied by mark ^or dot-
ted line with mark ^
are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifies par
une marque ^sont critiques
pour la s6curite.
Ne les remplacer que par une
piece portant le numero speci-
fic.
•:B+Line
•:B— Line
•UZ2 adjustment for repair.
•Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark :STOP
•Voltages are taken with aVOM (Input Impedance 10MQ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with aoscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•Circled numbers refer to waveforms.
•Signal path.
e£> :CD
17 --18 -

5-4. 1C BLOCK DIAGRAMS
IC102
LA6532M
IC301
CXD2500Q
O
o:O2zzW
•ooOOW)
iyj oq
BIAS
ASYI
ASYO
ASYE
NC
PSSL
WOCK
LRCK
V00
0A16
0A16
0A1A
0A13
0A12
DA11
DA 10
IC103
M54641
L
IC302
CXD2551P
Vcc Vcc
IC201
M5290P-16
IC304, 305
PCM56
19 -20-

f
NOTE:
•The mechanical parts with no reference
number in the exploded views are not
supplied.
•The construction parts of an assembled
part are indicated with acollation num-
ber in the remark column.
•Items marked are not stocked since
they are seldom required for routine
service. Some delay should be antici-
pated when ordering these items.
SECTION 6
EXPLODED VIEWS
•Due to standardization, parts with part
number suffix -XX and -X may be dif-
ferent from the parts specified in the
components used on the set.
•Color Indication of Appearance Parts
Example:
(RED) ...KNOB, BALANCE (WHITE)
tt
Cabinet's Color Parts' Color
No. Part No. Description Remarks No. Part No. Description Remarks
14-933-208-03 (E, AEP, AUS)... PANEL, LOADING 94-923-836-11 CUSHION
4-933-208-51 (US).. PANEL, LOADING 10 2-383-566-00 SCREW
11 7-682-547-09 SCREW +B 3X6
24-929-035-31 CASE 12 7-682-548-09 SCREW +BVTT 3X8 (S)
33-704-366-31 SCREW (CASE) (M3X6
)
13 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
14 7-682-547-04 SCREW +BVTT 3X6 (S)
4*3-703-244-00 (US,AEP,AU$) .
.
.BUSHING (2104), CORD
*3-703-571-11 (E)... 901 *A-4617-315-A (E)..,
*A-4617-494-A (US.AEP, AUS)... MOUNTED PCB. MAIN
5*4-933-201-11 (US).. ..PANEL, BACK
*4-933-201-31 (AEP )
.
..PANEL, BACK 905 1-575-002-11 WIRE, FLAT TYPE (22 CORE)
*4-933-201-41 (E)... ..PANEL, BACK
*4-933-201-91 (AUS). ..PANEL, BACK 907 A. 1-575-104-11 (E)..,...CORD, POWER
A. 1-575-105-11 (US).,...CORD, POWER
64-902-345-01 HEAT SINK A. 1-575-453-11 (AEP),...CORD, POWER
7*4-933-220-01 SPACER (MD) A. 1-575-677-11 (AUS),...CORD, POWER
8X-3304-938-2 (E, AEP, AUS)... FOOT ASSY 9908 A. 1-526-565-00 (E)..,.AC PLUG ADAPTOR
X-4885-950-1 (US).. FOOT ASSY 9Q201 8-729-111-67 TRANSISTOR 2SB1094-L
T701 A. 1-449-921-11 (US)., TRANSFORMER, POWER
T701 A. 1-449-922-11 (AEP, AUS)... TRANSFORMER, POWER
T701 A.l-449-923-11 (£)... TRANSFORMER, POWER
-20 -21 -

VIEWS
ation, parts with part
<and -X may be de-
parts specified in the
>n the set.
of Appearance Parts
,BALANCE (WHITE)
t
Parts' Color
The components identified by
mark ^or dotted line with mark
Aare critical for safety.
Replace only with part number
specified.
Les composants identifies par une
marque ^sont critiques pour la
securite.
Ne les remplacer que par une
piece portant le numero specife.
0. Part No. Description
94-923-836-11 CUSHION
10 2-383-566-00 SCREW
11 7-682-547-09 SCREW +B 3X6
12 7-682-548-09 SCREW +BYTT 3X8 (S)
13 7-685-646-79 SCREW +BYTP 3X8 TYPE2 N-S
14 7-682-547-04 SCREW +BVTT 3X6 (S)
Remarks
pi *A-4617-315-A
1*A-4617-494-A (E) MOUNTED PCB, MAIN
(US, AEP,AUS)... MOUNTED PCB, MAIN
1-575-002-11 WIRE, FLAT TYPE (22 CORE)
A. 1-575-104-11
A. 1-575-105-11
A. 1-575-453-11
A. 1-575-677-11
(E) CORD, POWER
(US).... CORD, POWER
(AEP) ...CORD, POWER
(AUS) ...CORD, POWER
6-2. FRONT PANEL SECTION
No. Part No. Description Remarks No. Part No.
51 X-4604-397-1 (AEP) PANEL ASSY, FRONT 52,58 57 4-928-635-01
X-4604-404-1 (E,AUS)... PANEL ASSY, FRONT 52,58 58 7-685-134-19
X-4933-214-1 (US) PANEL ASSY, FRONT 52,58 902 *1-632-243-11
903 *1-632-245-11
52 4-923-836-11 CUSHION
53 4-922-921-01 BUTTON (POWER) 904 *1-632-244-11
54 *4-927-353-01 SHEET (FL) 906 1-575-120-11
55 4-933-116-11 KNOB (C, TYPE), L0V FLD401.1-519-556-11
56 *4-933-204-01 BRACKET (H.P) J501 1-568-519-21
Description
SCREW, +BV (2.6X8) TAPPING
SCREW +BTP 2.6X8 TYPE2 N-S
PC BOARD, DISPLAY
PC BOARD, POWER SW
PC BOARD, HP
WIRE, FLAT TYPE (30 CORE)
INDICATOR TUBE, FLUORESCENT
JACK, LARGE TYPE
Remarks
D8 A. 1-526-565-00 (E) AC PLUG ADAPTOR
201 8-729-111-67 TRANSISTOR 2SB1094-L
7
7
01 A.l-449-921-11 (US) TRANSFORMER, POWER
'01 A. 1-449-922-11 (AEP, AUS) .. .TRANSFORMER, POWER
’01 A.l-449-923-11 (E) TRANSFORMER, POWER

CDP-590
6-3. MD SECTION-1 (CDM14-5BD1)
No. Part No. Description Remarks No. Part No. Description
301 4-933-111-01 CHASSIS (MD) 310 4-933-110-01 HOLDER (MG)
302 7-621-775-10 SCREW +B 2.6X4 311 A-4675-347-A MG ASSY
303 *4-917-583-21 BRACKET, YOKE 312 4-933-134-01 SCREW (+PTPWH M2. 6X6)
304 4-927-649-01 BELT 313 4-917-541-01 SPRING (B)
305 4-933-109-01 CAM 314 4-933-129-01 HOLDER (BU)
306 4-927-651-01 PULLEY (S) 315 4-933-108-01 SHAFT (CAM)
307 4-927-628-01 GEAR (C) M191 A-4604-363-A MOTOR (L) ASSY
308 4-933-107-01 GEAR (PL) 920 *1-632-202-11 PC BOARD, LOADING
309 4-933-112-01 TABLE, DISK
Remarks
-23-

CDP-590
6-4. MD SECTION-2 (BU-5BD1)
No. Part No. Description Remarks
351 7-685-134-19 SCREW +BTP 2.6X8 TYPE2 N-S
352 4-933-126-01 INSULATOR (A)
353 4-917-565-01 SHAFT, SLED
354 7-621-255-15 SCREW +P 2X3
355 4-917-567-01 GEAR (M)
356 4-917-564-01 GEAR (P), FLATNESS
Note: Note:
The components identi- Les composants identifies par
fied by mark ^or dot- une marque ^sont critiques
ted line with mark ^pour la security,
are critical for safety. Ne les remplacer que par une
Replace only with part piece portant le numero speci-
number specified. fie.
No. Part No. Description Remarks
921 *A-4617-161-A MOUNTED PCB, BD
923 1-575-001-11 WIRE, FLAT TYPE (12 CORE)
924 A. 8-848-144-11 DEVICE, OPTICAL KSS-240A
M101 X-4917-504-1 MOTOR ASSY (SLED)
M102 X-4917-523-3 MOTOR ASSY (SPINDLE)
-24 -

CDP-590
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
•Due to standardization, replacements in the parts
list may be different from the parts specified in
the diagrams or the components used on the set.
•Items marked "'* are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•If there are two or more same circuits in aset
such as astereophonic machine, only typical
circuit parts may be indicated and capacitors and
resistors in other same circuits may be omitted.
CAPACITORS:
MF:fi F,PF: fijif
.
RESISTORS
•All resistors are in ohms.
•F: nonflammable
COILS
SEMICONDUCTORS
In each case, U: n, for example:
UA...: juA..., UPA...: tiPA...,
UPC...: juPC, UPD. ..:juPD...
The components identified by
mark ^or dotted line with mark
Aare critical for safety.
Replace only with part number
specified.
Les composants identifies par une
marque ^sont critiques pour la
securite.
Ne les remplacer que par une
piece portant le numero specifie.
Ref .No. Part No. Description Ref .No. Part No. Description
901 *A-4617-315-A (E) ...MOUNTED PCB, MAIN C173 1-163-038-00 CERAMIC CHIP 0.1MF 25V
*A-4617-494-A (US.AEP.AUS)....MOUNTED PCB, MAIN C174 1-163-038-00 CERAMIC CHIP 0.1MF 25V
C201 1-126-842-11 ELECT 4700MF 20% 16V
902 *1-632-243-11 PC BOARD, DISPLAY
903 *1-632-245-11 PC BOARD, POWER SW C202 1-126-842-11 ELECT 4700MF 20% 16V
904 *1-632-244-11 PC BOARD, HP C203 1-126-880-11 ELECT 100MF 20% 63V
C204 1-126-059-11 ELECT 10MF 20% 50V
905 1-575-002-11 WIRE, FLAT TYPE (22 CORE)
906 1-575-120-11 WIRE, FLAT TYPE (30 CORE) C205 1-162-851-11 CERAMIC 0.1MF 20% 16V
C206 1-126-059-11 ELECT 10MF 20% 50V
907 A. 1-575-104-11 (E) .CORD,,POWER C207 1-124-045-00 ELECT 4.7MF 20% 50V
A. 1-575-105-11 (US)....XORDj,POWER
A. 1-575-453-11 (AEP ).CORD,,POWER C208 1-126-059-11 ELECT 10MF 20% 50V
A. 1-575-677-11 (AUS )
—
.CORD.,POWER C209 1-126-012-11 ELECT 470MF 20% 16V
C210 1-126-012-11 ELECT 470MF 20% 16V
908 .1-526-565-00 (E) AC PLUG ADAPTOR
920 *1-632-202-11 PC BOARD, LOADING C212 1-126-024-11 ELECT 220MF 20% 16V
921 *A-4617-161-A MOUNTED PCB, BD C301 1-124-994-11 ELECT 100MF 20% 10V
C302 1-126-301-11 ELECT IMF 20% 50V
923 1-575-001-11 WIRE, FLAT TYPE (12 CORE)
924 A.8-848-144-11 DEVICE, OPTICAL KSS-240A C304 1-136-161-00 FILM 0.047MF 5% 50V
C305 1-161-374-11 CERAMIC 0.0015MF 30% 16V
C101 1-163-038-00 CERAMIC CHIP 0.1MF 25V C306 1-164-159-11 CERAMIC 0.1MF 50V
C102 1-163-989-11 CERAMIC CHIP 0.033MF 10% 25V
C103 1-126-094-11 ELECT 4.7MF 20% 16V C307 1-162-306-11 CERAMIC 0.0 IMF 20% 16V
C308 1-126-300-11 ELECT 0.47MF 20% BOV
C104 1-163-038-00 CERAMIC CHIP 0.1MF 25V C309 1-164-159-11 CERAMIC 0.1MF 50V
C105 1-126-154-11 ELECT 47MF 20% 6.3V
C106 1-126-154-11 ELECT 47MF 20% 6.3V C310 1-164-159-11 CERAMIC 0.1MF BOV
C311 1-164-159-11 CERAMIC 0.1MF 50V
C107 1-126-154-11 ELECT 47MF 20% 6.3V C312 1-164-159-11 CERAMIC 0.1MF BOV
C108 1-163-038-00 CERAMIC CHIP 0.1MF 25V
C109 1-163-038-00 CERAMIC CHIP 0.1MF 25V C313 1-164-159-11 CERAMIC 0.1MF 50V
C314 1-164-159-11 CERAMIC 0.1MF 50V
C110 1-163-989-11 CERAMIC CHIP 0.033MF 10% 25V C315 1-164-159-11 CERAMIC 0.1MF 50V
cm 1-131-367-00 TANTALUM 22MF 20% 16V
Cl 12 1-164-232-11 CERAMIC CHIP 0.01MF 10% 50V C316 1-162-205-31 CERAMIC 18PF 5% 50V
C317 1-162-205-31 CERAMIC 18PF 5% BOV
Cl 13 1-164-232-11 CERAMIC CHIP 0.01MF 10% 50V C318 1-124-997-11 ELECT 470MF 20% 10V
Cl 14 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V
Cl 15 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V C319 1-124-997-11 ELECT 470MF 20% 10V
C320 1-130-481-00 MYLAR 0.0068MF 5% 50V
Cl 16 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V C321 1-130-481-00 MYLAR 0.0068MF 5% 50V
Cl 17 1-163-038-00 CERAMIC CHIP 0.1MF 25V
CUB 1-163-038-00 CERAMIC CHIP 0.1MF 25V C322 1-130-471-00 MYLAR 0.001MF 5% 50V
C323 1-130-471-00 MYLAR 0.00 IMF 5% 50V
Cl 19 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V C324 1-123-332-00 ELECT 47MF 20% 25V
C120 1-163-989-11 CERAMIC CHIP 0.033MF 10% 25V
C151 1-163-019-00 CERAMIC CHIP 0.0068MF 10% 50V C325 1-123-332-00 ELECT 47MF 20% 25V
C326 1-162-291-31 CERAMIC 560PF 10% 50V
C152 1-163-038-00 CERAMIC CHIP 0.1MF 25V C327 1-162-291-31 CERAMIC 56QPF 10% 50V
C153 1-163-006-11 CERAMIC CHIP 560PF 10% 50V
C154 1-164-161-11 CERAMIC CHIP 0.0022MF 10% 50V C328 1-124-893-11 ELECT 2200MF 20% 6.3V
C330 1-162-286-31 CERAMIC 220PF 10% 50V
C155 1-163-023-00 CERAMIC CHIP 0.015MF 10% 50V C331 1-162-286-31 CERAMIC 220PF 10% BOV
C171 1-163-038-00 CERAMIC CHIP 0.1MF 25V
C172 1-163-038-00 CERAMIC CHIP 0.1MF 25V C332 1-164-159-11 CERAMIC 0.1MF 50V
C333 1-164-159-11 CERAMIC 0.1MF 50V
C401 1-164-159-11 CERAMIC 0.1MF BOV
C402 1-164-159-11 CERAMIC 0.1MF 50V
-25 -

CDP-590
Ref. No. Part No. Description
C451 1-164-159-11 CERAMIC 0.1MF 50V
C503 1-162-291-31 CERAMIC 560PF 10% 50V
C504 1-162-291-31 CERAMIC 560PF 10% 50Y
CN101 1-568-796-11 SOCKET, CONNECTOR 22P
CN102 1-568-795-11 SOCKET, CONNECTOR 12P
CN103 *1-564-721-11 PIN, CONNECTOR (SMALL TYPE) 5P
CN301 *1-564-707-11 PIN, CONNECTOR (SMALL TYPE) 5P
CN502 *1-564-337-00 PIN, CONNECTOR 3P
CNP201*l-564-321-00 PIN, CONNECTOR 2P
CNP301*l-568-933-ll SOCKET, CONNECTOR 30P
CNP302*l-568-822-ll SOCKET, CONNECTOR 22P
CNP303*l-564-337-61 PIN, CONNECTOR 3P
CNP401*l-568-933-ll SOCKET, CONNECTOR 30P
D101 8-719-105-72 DIODE RD4.7M-B1
D201 8-719-200-82 DIODE 11ES2
D202 8-719-200-82 DIODE 11ES2
D203 8-719-200-82 DIODE 11ES2
D204 8-719-200-82 DIODE 11ES2
D205 8-719-200-82 DIODE 11ES2
D208 8-719-110-08 DIODE RD8.2ES-B2
D209 8-719-120-90 DIODE RD6.8ES-L3
D301 8-719-123-54 DIODE RD6.2ES-B2
D302 8-719-107-94 DIODE 1SS202-1
D401 8-719-933-57 DIODE HZS9B2L
D402 8-719-107-94 DIODE 1SS202-1
0403 8-719-107-94 DIODE 1SS202-1
D404 8-719-107-94 DIODE 1SS202-1
D405 8-719-107-94 DIODE 1SS202-1
D406 8-719-107-94 DIODE 1SS202-1
D407 8-719-107-94 DIODE 1SS202-1
D408 8-719-107-94 DIODE 1SS202-1
D409 8-719-107-94 DIODE 1SS202-1
D410 8-719-107-94 DIODE 1SS202-1
FLD401 1-519-556-11 INDICATOR TUBE, FLUORESCENT
IC101 8-752-037-33 IC CXA1372Q
IC102 8-759-821-94 IC LA6532M
IC103 8-759-633-65 IC M54641L
IC201 8-759-630-21 IC M5290P-16
IC202 8-759-633-42 IC M5293L
IC301 8-752-333-31 IC CXD2500Q
IC302 8-752-334-06 IC CXD2551P
IC303 8-759-917-18 IC SN74HCU04N
IC304 8-759-998-22 IC PCM56P
IC305 8-759-998-22 IC PCM56P
IC306 8-759-631-39 IC M5204P
IC401 8-759-150-29 IC UPD75212AGF-522-3BE
IC451 8-749-920-83 IC GP1U52XB
J101 1-216-295-00 METAL GLAZE 05% 1/10W
J102 1-216-295-00 METAL GLAZE 05% 1/1 OW
J401 1-566-921-11 JACK, PIN 2P (LINE OUT L/R)
J501 1-568-519-21 JACK, LARGE TYPE (PHONES)
M101 X-4917-504-1 MOTOR ASSY (SLED)
Ml02 X-4917-523-3 MOTOR ASSY (SPINDLE)
M191 A-4604-363-A MOTOR (L) ASSY
PS201A. 1-532-685-00 LINK, IC
PS202A. 1-532-637-00 LINK, IC
Q101 8-729-901-01 TRANSISTOR DTC144EK
Q201 8-729-111-67 TRANSISTOR 2SB1094-L
Q202 8-729-140-96 TRANSISTOR 2SD774-34
Ref. No. Part No. Description
Q203 8-729-111-67 TRANSISTOR 2SB1094-•L
Q204 8-729-230-45 TRANSISTOR 2SC2458-•YGR
Q206 8-729-119-76 TRANSISTOR 2SAU75-•HFE
R101 1-216-097-00 METAL GLAZE 100K 5% 1/10W
R102 1-216-097-00 METAL GLAZE 100K 5% 1/10W
R103 1-216-091-00 METAL GLAZE 56K 5% l/LOW
R104 1-216-099-00 METAL GLAZE 120K 5% 1/10W
R105 1-216-069-00 METAL GLAZE 6.8K 5% 1/10W
R106 1-216-061-00 METAL GLAZE 3.3K 5% 1/10W
R107 1-216-114-00 METAL GLAZE 510K 5% 1/10W
R108 1-216-105-00 METAL GLAZE 220K 5% 1/10W
R109 1-216-061-00 METAL GLAZE 3.3K 5% 1/10W
R110 1-216-049-00 METAL GLAZE IK 5% 1/10W
Rill 1-216-049-00 METAL GLAZE IK 5% 1/10W
R112 1-216-083-00 METAL GLAZE 27K 5% 1/10W
R113 1-216-071-00 METAL GLAZE 8.2K 5% 1/10W
R114 1-216-105-00 METAL GLAZE 220K 5% 1/10W
R152 1-216-073-00 METAL GLAZE 10K 5% 1/10W
R153 1-216-085-00 METAL GLAZE 33K 5% 1/10W
R154 1-216-085-00 METAL GLAZE 33K 5% 1/10W
R155 1-216-093-00 METAL GLAZE 68K 5% 1/10W
R156 1-216-081-00 METAL GLAZE 22K 5% 1/10W
R157 1-216-079-00 METAL GLAZE 18K 5% 1/10W
R158 1-216-079-00 METAL GLAZE 18K 5% 1/10W
R159 1-216-079-00 METAL GLAZE 18K 5% 1/10W
R160 1-216-049-00 METAL GLAZE IK 5% 1/10W
R171 1-216-001-00 METAL GLAZE 10 5% 1/10W
R172 1-216-001-00 METAL GLAZE 10 5% 1/10W
R173 1-216-001-00 METAL GLAZE 10 5% 1/10W
R174 1-216-001-00 METAL GLAZE 10 5% 1/10W
R201 1-249-425-11 CARBON 4.7K 5% 1/4W
R202 1-249-425-11 CARBON 4.7K 5% 1/4W
R203 1-249-438-11 CARBON 56K 5% 1/4W
R204 1-249-429-11 CARBON 10K 5% 1/4W
R205 1-249-435-11 CARBON 33K 5% 1/4W
R208 1-249-423-11 CARBON 3.3K 5% 1/4W
R209 1-249-417-11 CARBON IK 5% 1/4W
R210 1-249-417-11 CARBON IK 5% 1/4W
R302 1-249-417-11 CARBON IK 5% 1/4W
R303 1-249-417-11 CARBON IK 5% 1/4W
R304 1-249-417-11 CARBON IK 5% 1/4Vi
R305 1-249-417-11 CARBON IK 5% 1/4W
R308 1-249-423-11 CARBON 3.3K 5% 1/4W
R309 1-249-423-11 CARBON 3.3K 5% 1/4W
R310 1-249-429-11 CARBON 10K 5% 1/4W
R311 1-249-429-11 CARBON 10K 5% 1/4W
R312 1-249-441-11 CARBON 100K 5% 1/4W
R313 1-249-417-11 CARBON IK 5% 1/4W
R314 1-249-417-11 CARBON IK 5% 1/4W
R315 1-249-420-11 CARBON 1.8K 5% 1/4W
R316 1-249-418-11 CARBON 1.2K 5% 1/4W
R317 1-249-417-11 CARBON IK 5% 1/4W
R318 1-249-417-11 CARBON IK 5% 1/4W
R319 1-249-417-11 CARBON IK 5% 1/4W
Note: Note:
The components identi- Les composants identifies par
fied by mark ^or dot- une marque Asont critiques
ted line with mark ^pour la security
are critical for safety. Ne les remplacer que par une
Replace only with part piece portant le numero speci-
number specified. fie.
26 -