Sony CDP-CE105 User manual
— 1 —
MICROFILM
COMPACT DISC PLAYER
SERVICE MANUAL
Model Name Using Similar Mechanism HCD-D670AV/N555AV
CD Mechanism type CDM37-5BD19
Base Unit Type BU-5BD19
Optical Pick-up type KSS-213BA/F-NP
SPECIFICATIONS
CDP-CE105
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Australia 240V AC, 50Hz
USA
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 2 —
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LESCOMPOSANTSIDENTIFIÉSPAR UNE MARQUE!SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE
WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
This caution label
is located inside
the unit.
TABLE OF CONTEMTS
1. SERVICING NOTE ........................................................... 4
2. GENERAL ............................................................................ 5
3. DISASSEMBLY
3-1. Front Panel Block .................................................................. 6
3-2. CD Mechanism Deck ............................................................. 6
3-3. BU Bracket Assembly............................................................ 7
3-4. Disc Table .............................................................................. 7
4. TEST MODE ........................................................................ 8
5. ELECTRICAL BLOCK ADJUSTMENTS ................. 9
6. DIAGRAMS
6-1. Circuit Boards Location ...................................................... 11
6-2. Schematic Diagram — BD Section — ................................ 12
6-3. Printed Wiring Board — BD Section —.............................. 15
6-4. Schematic Diagram — Main Section — ............................. 19
6-5. Printed Wiring Board — Main Section —........................... 23
6-6. IC Pin Function
• IC401 System Control, Fluorescent Indicator Tube Drive
(CXP82316-065Q)............................................................ 26
7. EXPLODED VIEWS
7-1. Case and Back Panel Section ............................................... 27
7-2. Front Panel Section .............................................................. 28
7-3. CD Mechanism Section (CDM37-5BD19).......................... 29
7-4. Base Unit Section (BU-5BD19)........................................... 30
8. ELECTRICAL PARTS LIST ......................................... 31
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 3 —
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety checks before releasing the set to the customer:
Checkthe antenna terminals, metal trim,“metallized” knobs,screws,
and all other exposed metal parts forAC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers). Leak-
age current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of aVOM
or battery-operatedAC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
To Exposed Metal
Parts on Set
0.15
µ
F1.5k
Ω
AC
voltmeter
(0.75V)
Earth Ground
MODEL IDENTIFICATION
— BACK PANEL —
4-982-187-
123
1
2
3
123
0π: US model
1π: Canadian model
2π: Australian model
3π: AEP, German model
5π: UK model
7π: E model
8π: Singapore model
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 4 —
SECTION 1
SERVICING NOTE
How to take out a compact disc when the power is turn OFF.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-up
block. Therefore, when checking the laser diode emission, observe
from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveform is output.
Rotate the table motor into the
directionof arrow, lefthe spindle
motor down and take out the
compact disc.
Compact disc
Table motor
Compact disc
Spindle motor
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 5 —
SECTION 2
GENERAL
LOCATION OF CONTROLS
1POWER switch
2Front cover
3OPEN switch
4Display window
5CONTINUE button
6SHUFFLE button
7PROGRAM button
8REPEAT button
9DISC SKIP button
0)±(manual search, AMS*) button
!¡ ≠0(manual search, AMS*) button
!™ p(STOP) button
!£ ·P(play, pause) button
!¢ DISC 1-5 buttons
* AMS is the abbreviation for Automatic Music Sensor.
1234
5678 9
0!¡!™!£!¢
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 6 —
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-1. FRONT PANEL BLOCK
1
Remove the case.
2
Flat type wire (19 core)
(Main board, CN302)
3
Screw (BVTT 3x8)
4
Two screws (BVTT 3x8)
Claw
Claw
3-2. CD MECHANISM DECK
1
Flat type wire (20 core)
(Main board, CN304)
2
Connector 9P
(Main board, CN303)
3
Two screws (BVTT3x6)
4
Three screws (BVTT 3x6)
5
CD mechanism deck
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 7 —
3-3. BU BRACKET ASSEMBLY
1
Yoke bracket
2
BU bracket assembly
3-4. DISC TABLE
Note:
When the Disc table is installed, adjust the positions
of Roller cam and mark (as shown in the figure, then
set to the groove of disc table. 1
Screw (BVTP 3x8)
2
Screw (BVTP 3x8)
3
Bracket (BU)
4
Step screw
5
Disc table
A
A
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 8 —
SECTION 4
TEST MODE
4-1. AF MODE
The following checks can be performed in the AF mode, which is
set by connecting the test point (AFJ) terminal on DISPLAY
board to the Ground and turning on the power.
• FL tube check
After all segments light up, when the ≠0 button is pressed,
the following will be displayed. (Partial lighting 1)
4-2. ADJ MODE
The following operations are performed in the ADJ mode, which
is set by connecting the test point (ADJ) terminal to the Ground and
turning on the power.
• Servo related manual operations and measurement can be
performed.
(For details of operations, refer to Table of Key Operations inADJ
Mode.)
TABLE OF BUTTON OPERATIONS IN ADJ MODE
The functions of the number buttons are shown in the following
table.
FUNCTIONS OF NUMBER BUTTONS
(Use the widely use remote commander with 20 keys.)
Function
15
16
17
18
19
20
S curve check (in stop mode)
Tracking servo, sled servo off
Tracking servo, sled servo on
E-F balance indication
E-F balance indicati down
E-F balance indication up
Button
[ DISPLAY BOARD ] — Conductor Side —
(Partial lighting 1)
When the )± button is pressed, the following will be dis-
played. (partial lighting 2)
(Partial lighting 2)
When the pbutton is pressed, all will light up again.
• Key check
All buttons have corresponding button numbers. When a button
is pressed, the counter will count up and display the button’s num-
ber. However, the counter will only count to “14”. It will not count
for buttonsalreadypressedonce, but will display thebutton’s num-
ber.
ÂÂ
Display of button
number
Display of counting
DISC 4
DISC 5
CONTINUE
SHUFFLE
PROGRAM
REPEAT
DISC SKIP
07
All lit
Partial lighting 1
Partial lighting 2
08
09
10
Button No.
Displayed Button No.
Displayed
·P
p
≠0
)±
DISC 1
DISC 2
DISC 3
18
17
13
12
11
19
20
Button Button
IC401
R404 R405
TP
AFJ
TP
ADJ
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 9 —
Note :
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. UseYEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicatior with neutral detergent when
the signal level is low than specified value with the following
checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias Adjustment
Procedure :
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turn Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that osilloscope waveform is clear and check RF signal
level is correct or not.
Note : Clear RF signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500nS
Procedure :
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (ADJ) on DISPLAY board to
Ground with a lead wire.
3. Turn Power switch on to set theADJ mode.
4. Put disc (YEDS-18) in and set to the stop mode.
5. Press the “15” button and actuate the focus serach.
6. Check the oscilloscope waveform (S-curve) is symmetrical
betweenA and B.And confirm peak to peak level within 2.4 ± 0.7
Vp-p.
S-curve waveform
level : 1.3 ± 0.3 Vp-p
Symmetry
within 2.4 ± 0.7 Vp-p
A
B
oscilloscope
BD board
TP(RF)
TP(VC)
7. After check, remove the lead wire connected in step 2.
Note : • Try to measure several times to make sure than the ratio of
A : B or B :A is more than 10 :7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
RF Level Check
SECTION 5
ELECTRICAL BLOCK ADJUSTMENTS
oscilloscope
(DC range)
BD board
TP(RF)
TP(VC)
Procedure :
1. Connect oscilloscope to test point TP (RF).
(Ground terminal : VC)
2. Turn Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Adjust RV101 so that the waveform is clear.
(Clear RF signal waveform means that the shape “◊”can be clearly
distinguished at the center of the waveform.)
5. After adjustment, check the RF signal level.
• RF signal
VOLT/DIV : 200 mV
TIME/DIV : 500 nS
level
1.3 ± 0.3 Vp-p
TP(FEO)
TP(VC)
BD board
oscilloscope
S Curve Check
Note : Use the widely use remote commander with 20 keys for this
check.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 10 —
Adjustment Location
[BD BOARD] (Conductor Side)
RF FOK
RV101
RV103
IC101 IC102
TEI
FEI
TEO
RV102
VC
GND
PCK
FEO
TP(TEO)
TP(VC)
oscilloscope
BD board
Procedure :
1. Connect test point TP (ADJ) on DISPLAY board to Ground with
a lead wire.
2. Connect oscilloscope to test point TP (TEO).
3. Turn Power switch on to set the ADJ mode.
4. Put disc (YEDS-18) in and playback.
5. Press the “16” button. (The tracking servo and the sledding servo
are turn off)
6. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0Vdc, and check this level.
Traverse waveform
0V
B
A
level : 300 ± 100 mVp-p
Specified level : • X 100=less than ± 7%
• A+B=300 ± 100 mVp-p
7. Remove the lead wire connected in step 1.
Focus/Tracking Gain Adjustment (RV102, RV103)
This gain has a margin, so even if it is slightly off.
There is no problem.
Therfore, do not perform this adjustment.
Please note that it should be fixed to mechanical center position when
you moved and do not know original position.
A-B
2(A+B)
IC104
IC401
R404
TP
ADJ
R405
TP
AFJ
Note : Use the widely use remote commander with 20 keys for this
check.
E-F Balance Check
[DISPLAY BOARD] (Conductor Side)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 11 —
SECTION 6
DIAGRAMS
6-1. CIRCUIT BOARDS LOCATION
LED board
BD board
TABLE SENSOR board
CD MOTOR board
MAIN board
FUNCTION board
DISPLAY board
DOOR SW board
POWER SW board
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 26 —
6-6. IC PIN FUNCTION
• IC401 SYSTEM CONTROL, FLUORESCENT INDICATOR TUBE DRIVE (CXP82316-065Q)
Function
Connected to Ground.
Remote control signal input.
Connected to Ground.
Serial data latch signal output.
Not used. (Open)
CD Table sensor signal input.
Latch signal output to digital filter (IC104).
Serial clock output.
Audio muting control signal output.
Serial data output.
Read out clock output for subcode Q data.
Subcode Q data input.
Not used. (Open)
Table motor control signal output.
Disc number LED drive signal output.
Not used. (Open)
Disc table up detect.
Key input (S511 to S517, S521 to S527)
+5V pin.
CD door open detection input.
ADJ test mode input. The equipment is fixed at “H”.
AFJ test mode input. The equipment is fixed at “H”.
Connected to Ground.
Connected to Ground.
Reset signal input.
Clock input. (5.08 MHz)
Clock output. (5.08 MHz)
Ground
Not used. (Open)
Fluorescent Indicator Tube segment output.
Not used. (Open)
Fluorescent Indicator Tube grid (timing) output.
–30V pin for Fluorescent Indicator tube.
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 to 21
22
23
24
25
26
27
28
29
30
31
32
33
34 to 45
46 to 60
61 to 63
64 to 70
71
72
73
74 to 76
77
78
79
80
Connected to Ground.
Focus switch signal output.
Connected to Ground.
Read out timing signal input for subcode Q data.
SENSE signal input.
Pin Name
—
RM IN
—
XLT
—
T.SENSE
PRGL
CLK
MUTE
DATA
SQCK
SUBQ
—
TBL.R
TBL.L
LED
—
UPSW
KET 1
KEY 2
DOOR SW
ADJ
AFJ
—
—
RST
EXTAL
XTAL
VSS
—
P1 to P15
—
1G to 7G
VG
VDD (+5V)
—
—
FSW
—
SCOR
SENS
I/O
–
I
–
O
–
I
O
O
O
O
O
I
–
O
O
O
–
I
I
I
I
I
I
–
–
I
I
O
–
–
O
–
O
–
–
–
–
O
–
I
O
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 27 —
6 3-703-571-11 BUSHING (S) (4516), CORD (E)
7 1-777-157-11 WIRE (FLAT TYPE) (19 CORE)
8 1-777-158-11 WIRE (FLAT TYPE) (22 CORE)
9 X-4941-228-1 FOOT (F22125H-M)
10 4-956-370-02 BAND, PLUG FIXED (UK,AUS)
!CNP901 1-575-042-21 CORD, POWER (US,CND)
!CNP901 1-575-651-21 CORD, POWER (AEP,G,SP)
!CNP901 1-696-027-11 CORD, POWER (E)
!CNP901 1-696-845-11 CORD, POWER (AUS)
!CNP901 1-751-529-11 CORD, POWER (UK)
!T301 1-429-650-11 TRANSFORMER, POWER (US,CND)
!T301 1-429-651-11 TRANSFORMER, POWER (AEP,UK,G,AUS,SP)
!T301 1-429-652-11 TRANSFORMER, POWER (E)
*1 4-982-186-11 CASE
2 3-363-099-01 SCREW (CASE 3 TP2)
*3 4-982-187-01 PANEL, BACK (US)
*3 4-982-187-11 PANEL, BACK (CND)
*3 4-982-187-21 PANEL, BACK (AUS)
*3 4-982-187-31 PANEL, BACK (AEP,G)
*3 4-982-187-51 PANEL, BACK (UK)
*3 4-982-187-71 PANEL, BACK (E)
*3 4-982-187-81 PANEL, BACK (SP)
!4 1-569-007-11 ADAPTOR, CONVERSION 2P (E)
!4 1-569-008-11 ADAPTOR, CONVERSION 2P (SP)
*5 A-4699-011-A MAIN BOARD, COMPLETE (AEP,UK,G,AUS,SP)
*5 A-4699-012-A MAIN BOARD, COMPLETE (E)
*5 A-4699-249-A MAIN BOARD, COMPLETE (US,CND)
*6 3-703-244-00 BUSHING (2104), CORD
(US,CND,AEP,UK,G,AUS,SP)
SECTION 7
EXPLODEDVIEWS
NOTE:
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and pack-
ing materials are given in the last of this parts list.
• Abbreviation
CND : Canadian model
G : German model
SP : Singapore model.
AUS : Australian model
7-1. CASE AND BACK PANEL SECTION
The components identified by mark !
or dotted line with mark !are critical
for safety.
Replace only with part number speci-
fied.
Les composants identifiés par une
marque!sont critiquespour la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
#1
not supplied
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
AEP, G, SP models
CNP901
4
SP model
E model CNP901
4
UK model
CNP901
US, CND models
CNP901
AUS model
CNP901
310 6
#2
#1
T301
5
#3
#3
2
#3
#3
7
#3
8
#3
#3
9
not supplied
not supplied
#2
not supplied
9
#1
#1
FPONT PANEL
CDM37-5BD19
1
2
not supplied
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 28 —
7-2. FRONT PANEL SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
51 4-951-620-01 SCREW (2.6X8), +BVTP
*52 1-661-174-11 FUNCTION BOARD
53 4-982-194-01 BUTTON
54 4-982-196-02 BASE, BUTTON
55 4-977-358-11 CUSHION (8X12.5)
56 4-982-192-01 PLATE, INDICATION
57 4-963-404-21 EMBLEM (5-A), SONY
58 4-982-188-01 PANEL, FRONT
59 3-931-429-01 BUTTON (POWER)
*60 1-661-175-11 POWER SW BOARD
61 A-4672-189-A LEVER ASSY, LOCK
62 4-933-134-01 SCREW (+PTPWH M2.6X6)
63 4-982-199-01 SPRING (LEVER), TORSION
*64 4-982-198-01 BRACKET (BUTTON)
65 4-982-193-01 BUTTON (OPEN)
66 3-701-443-11 WASHER
67 4-982-191-01 DOOR
68 3-354-963-01 DAMPER
69 4-982-190-02 COVER
*70 1-661-176-11 DOOR SW BOARD
71 4-982-195-01 SPRING (DOOR), TORSION
*72 A-4699-013-A DISPLAY BOARD, COMPLETE
73 4-977-593-11 RING (DIA. 50), ORNAMENTAL
(EXCEPT US,CND)
FL401 1-517-522-11 INDICATOR TUBE, FLUORESCENT
51
51
51
51
51
51
51
51
51
5151
52
53
54
55
55
57
58
59
60
61
62
62
63
65 64
66
66
67
68 69
70
71
72
73
73
56
FL401
not supplied
not supplied
EXCEPT US, CND models
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 29 —
#2
#2
#2
#2
362
352
366
365
367
361
368
369
370
368 368
369
371
M201
353
357
361
#2
360
359 359
358
363
351
351
352
351
354 355
360
359 356
360
BU-5BD19
364
not
supplied
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
7-3. CD MECHANISM SECTION (CDM37-5BD19)
351 4-978-423-01 SCREW, STEP
352 4-944-490-01 BELT (TIMING)
353 A-4660-978-A GEAR (PULLEY) ASSY
354 4-978-421-01 GEAR (MID)
355 4-978-425-01 ROLLER (CAM)
356 4-978-420-01 CAM (HOLDER)
357 1-452-538-11 MAGNET
358 4-978-417-01 TABLE, DISC
359 4-934-376-01 SHAFT (ROLLER)
360 X-4924-457-1 ROLLER ASSY
*361 4-978-583-01 BRACKET (BU)
*362 4-978-418-01 CHASSIS
*363 4-980-385-01 HOLDER (SW)
*364 A-4673-765-A CD MOTOR BOARD, COMPLETE
365 4-978-426-01 INDICATOR (NO.)
*366 1-659-059-13 LED BOARD
*367 1-659-058-13 TABLE SENSOR BOARD
368 4-933-134-01 SCREW (+PTPWH M2.6X6)
369 4-958-593-01 SPRING (BU), COMPRESSION
*370 4-978-419-01 HOLDER (BU-5)
371 4-917-583-71 BRACKET, YOKE
M201 A-4660-977-A MOTOR ASSY (TABLE)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
— 30 —
Ref. No. Part No. Description Remark
Ref. No. Part No. Description Remark
403
r
A
7-4. BASE UNIT SECTION (BU-5BD19) 401
402
M102
404
S101
M101
(including
r
A)
#4
405
406
407
404
408
!401 8-848-367-11 OPTICAL PICK-UP KSS-213BA/F-NP
402 1-769-069-11 WIRE (FLAT TYPE)(16 CORE)
403 4-917-567-01 GEAR (M)
404 4-951-940-01 INSULATOR (BU)
405 4-917-565-01 SHAFT, SLED
406 4-917-564-01 GEAR (P), FLATNESS
*407 A-4673-402-A BD BOARD, COMPLETE
408 4-951-620-01 SCREW (2.6X8), +BVTP
M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
M102 X-4917-504-1 MOTOR ASSY (SLED)
S101 1-572-085-11 SWITCH, LEAF (LIMIT)
The components identified by mark !
or dotted line with mark !are critical
for safety.
Replace only with part number speci-
fied.
Les composants identifiés par une
marque!sont critiques pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro spécifié.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
Other manuals for CDP-CE105
3
Table of contents
Other Sony CD Player manuals
Sony
Sony CFS-1058S User manual
Sony
Sony Walkman D-FJ003 User manual
Sony
Sony CDP-CA80ES - Es Compact Disc Player User manual
Sony
Sony CFD-E90L User manual
Sony
Sony DVP-SR200P User manual
Sony
Sony D-EJ360 - PSYC CD Walkman User manual
Sony
Sony DSJ301 - S2 Sports CD Walkman User manual
Sony
Sony CDX-5V661A User manual
Sony
Sony D-E330 - Portable Cd Player User manual
Sony
Sony CDX-GT385 User manual
Sony
Sony CDP-XE700 User manual
Sony
Sony Walkman D-EJ700 User manual
Sony
Sony CDX-MP450X Primary User Manual (English User manual
Sony
Sony Sports CD Walkman D-ES51 User manual
Sony
Sony MZ-NE410 - Net MD Walkman MiniDisc Recorder Setup guide
Sony
Sony Walkman D-EJ101 User manual
Sony
Sony Walkman D-FS601 User manual
Sony
Sony Walkman D-EJ010 User manual
Sony
Sony D-FJ401 - Discman User manual
Sony
Sony CD Walkman D-NE500 User manual
