Sony DSC-S780 User manual

Sony EMCS Co.
DSC-S780 2008G0200-1
© 2008.07
Published by KohdaTEC9-852-289-12
Revision History
Revision History
Internal memory
ON BOARD
Internal memory
ON BOARD
SERVICE MANUAL
Link
Link
SERVICE NOTE
SPECIFICATIONS
BLOCK DIAGRAM
DISASSEMBLY REPAIR PARTS LIST
Ver. 1.1 2008.07
DIGITAL STILL CAMERA
US Model
Canadian Model
AEP Model
UK Model
E Model
Korea Model
Argentine Model
The components identified by
mark or dotted line with
mark are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DSC-S780
In case of the lens block assy, main board, or main frame assy failure,
contact your local Sony Service Headquarter for the measures.
Revised-1
Replace the previously issued
SERVICE MANUAL 9-852-289-11
with this Manual.

DSC-S780 — 2 —
SPECIFICATIONS
Camera
[System]
Image device:
7.18 mm (1/2.5 type) color CCD, Primary
color filter
Total pixel number of camera:
Approx. 8 286 624 pixels
Effective pixel number of camera:
Approx. 8 083 560 pixels
Lens: 3×zoom lens f = 5.8 –17.4 mm (35 –
105 mm (35mm film equivalent)) F2.8 (W) –
4.8 (T)
Exposure control: Automatic exposure, Scene
Selection (7 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent, Incandescent, Flash
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: AVI (Motion JPEG)
Recording media: Internal Memory (approx.
22 MB), "Memory Stick Duo"
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index) set to Auto):
approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to
11 feet 5 7/8 inches) (W)/approx. 0.5 to 2.0 m
(1 feet 7 3/4 inches to 6 feet 6 3/4 inches) (T)
[Input and Output connectors]
(USB) A/V OUT terminal:
Video, Audio (Monaural), USB
communication
USB communication:
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel: 6.2 cm (2.5 type) TFT drive
Total number of dots: 153 600 (640×240) dots
BC-CSK battery charger
Power requirements: AC 100 V to 240 V, 50/
60 Hz, 2.2 W
Output voltage: DC 4.2 V, 0.33 A
Operating temperature: 0 to 40 (32 to 104 F)
Storage temperature: –20 to +60 (–4 to
+140 F)
Dimensions: Approx. 62×24×91mm (2 1/2×31/
32×3 5/8 inches) (W/H/D)
Mass: Approx. 75 g (2.7 oz)
Rechargeable battery pack NP-
BK1
Used battery: Lithium-ion battery
Maximum output voltage: DC 4.2 V
Mean output voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.4 A
Capacity: Approx.3.4 Wh (970 mAh)
Design and specifications are subject to change
without notice.
[Power, general]
Power: Rechargeable battery pack NP-BK1, 3.6 V
AC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting):
1.3 W
Operating temperature: 0 to 40 (32 to 104 F)C
Storage temperature: –20 to +60 (–4 to +140
Dimensions: 90.8×56.0×26.5 mm (3 5/8×2 1/4×1
1/16 inches) (W/H/D, excluding protrusions)
Mass: Approx. 150 g (5.3 oz) (including NP-BK1
battery pack and strap, etc.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
PictBridge: Compatible
C F)
CC

— 3 —
DSC-S780
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINEWITH
MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE SUR LES
DIAGRAMMESSCHÉMATIQUES ET LALISTEDESPIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. Check the areaofyourrepairfor unsoldered or poorly-soldered
connections. Check the entireboard surfaceforsolder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, showobvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. FLEXIBLE Circuit Board Repairing
Keep the temperature of the soldering iron around 270 C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Dangerof explosionifbatteryisincorrectly replaced.
Replace only with the same or equivalent type.

— 4 —
DSC-S780
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Process After Fixing Flash Error·····································1-1
1-2. Method for Copying or Erasing the Data in Internal
Memory ···········································································1-1
2. DISASSEMBLY
2-1. Disassembly·····································································2-1
3. BLOCK DIAGRAM
3-1. Overall Block Diagram ···················································3-1
4. REPAIR PARTS LIST
4-1. Exploded Views ·······························································4-1
4-1-1. Overall Section ······························································4-1
4-1-2. Main Frame Block ·························································4-2
4-1-3. Cabinet (Rear) Block ·····················································4-3
4-44-1-4. Lens Block ·····································································
4-2. Accessories ······································································4-5
Section Title Page
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.07

1-1
DSC-S780
mory.)The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal me
Note: When replacing the camera, erase the data in internal memory of the board before replacement.
Method for Copying the Data in Internal Memory
1. SERVICE NOTE
1-1. PROCESS AFTER FIXING FLASH ERROR
1-2. METHOD FOR COPYING OR ERASINGTHE DATA IN INTERNAL MEMORY
Copies all images in the internal memory to a "Memory Stick Duo".
Insert a "Memory Stick Duo" having sufficient free capacity.
Select [OK] with on the control button, then press .
The message "All data in internal memory will be copied Ready?" appears.
Select [OK] with , then press .
Copying starts.
To cancel copying
Select [Cancel] in step or , then press .
Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
You cannot select images to copy.
The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the "Memory Stick Duo" after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
A new folder is created on the "Memory Stick Duo" and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
The (Print order) marks on the images are not copied.
Copy
Method for Initializing the Flash Error
Initializes the setting to the default setting.
Even if you execute this function, the images stored in the internal memory are retained.
Select [OK] with on the control button, then press .
The message "Initialize all settings Ready?" appears.
Select [OK] with , then press .
The settings are reset to the default setting.
To cancel initializing
Select [Cancel] in step or , then press .
Be sure not to power off the camera while initializing.
Initialize
Method for Formatting the Internal Memory
This item does not appear when a "Memory Stick Duo"is inserted in the camera.
Formats the internal memory.
Note that formatting permanently erases all data in the internal memory, including even protected images.
Select [OK] with on the control button, then press .
The message "All data in internal memory will be erased Ready?" appears.
Select [OK] with , then press .
The format is complete.
To cancel formatting
Select [Cancel] in step or , then press .
Format

2-1
DSC-S780
2-1. DISASSEMBLY
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
SCREW_TP_1.7_3.5_A_0.4_D=3
(To 2-2 Page)
MIDDLE COVER R
MIDDLE COVER L
SCREW_TP_1.7_3.5_A_0.4_D=3
SCREW TP _1.7_2_A_0.4_D=3
SCREW_TP_1.7_3_A_0.4_D=3
SCREW_TP_1.7_2.7_A_0.4_D=3
JACK COVER
CABINET (FRONT) ASSY
SCREW TP _1.7_3_A_0.4_D=3
SCREW_TP_1.7_7.5_A_0.5_D=2.5
FFC1 (SW)
MODE DIAL
SW BLOCK ASSY
SW BUTTON
CABINET (REAR) ASSY
SCREW_TP_1.4_3_A_0.3_D=2.5
LCD
SCREW_TP_1.7_2_A_0.4_D=3
SP SHEET METAL
SCREW_TP_1.7_3_A_0.4_D=3
LCD PLATE
7

Shorting jig
(1kΩ/ 1W)
Caution
SCREW_TP_1.7_3_A_0.4_D=3
(From 2-1 Page)
FFC2 (RL)
ST BLOCK ASSY
RL BLOCK
BT LID
LENS BLOCK ASSY
MAIN FRAME ASSY
SCREW_TP_1.4_3_A_0.3_D=2.5
BLOCK ASSY PROTECTION SHEET
FPC
SCREW_TP_1.4_3_A_0.3_D=2.5
SCREW_TP_1.4_3_A_0.3_D=2.5
CCD ASSY
LOW PASS FILTER SET
SCREW_TP_1.7_3.5_A_0.4_D=3
MAIN MOUNT
HELP02
HELP02
HELP01
HELP03
HELP01
DSC-S780 2-2
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.07

HELP
DSC-S780
HELP
Be careful about the Lens Assy.
Attach the Block assy protection sheet as shown.
Don't press the Sensor holder
Don't press the AF Motor
Be careful of the weld
Keep clean these Pins.
Attach the Block assy
protection sheet avoiding
three screw holes.
Attach the Block assy
protection sheet avoiding
four screws.
Block assy
protection sheet
Don't press the Barrier part.
HELP01
HELP02
HELP03
Ver. 1.1 2008.07

3-1
DSC-S780
3-1. OVERALL BLOCK DIAGRAM
3. BLOCK DIAGRAM
SUB
-7.5V
BL-
DGND
DGND
DGND
DGND
+15V
H1 H2 HL
+2.5VD +3.1VD
-7.5V
+5VM
+5VM
+3.1VC
BL+
+3.3V
DGND
+13V
DGND
RG
+3.1VD
ALE
CCD_OUT
+3.1VD
V1 V2A V2B V3A V3B
+3.1VD
DGND
+3.3V
DGND
+3.1VC
-7.5V
+13V
+3.1VD
+3.1VD
DGND
VD
RAMREF
RAMCAS
RAMCLK_EN
IN2B
IN1B
LINE_OUT
+3.1VD
RAMUDQS
SPKRP
FA22
RAMA[0..14]
RAMRAS
LENS_SDATA
LCD_VD
+1.8VD
TG_ON
RAMWE_N
SHUTTER_M1
PWR_CTRL
RE
WP
IN3B
HD
LCD_MCLK
VP
DGND
CE0
PW_LED
RAMCLK
VIDEO_OUT
FA21
RAMCS_N
LCD_D[0..7]
PWROFF_DET
SHUTTER_M0
LENS_EN
LENS_PS
PWR_ON
ZOOM_M0
IN2A
TG_CS
LCD_HD
SHUT2
IN3A
BAT_LEVEL
CARD_ON
D-
D+
PXCLK
ZOOM_PR
BL
RAMD[0..15]
RAMLDM
RAMCLK_N
FA23
USB_DET
CDS_EN
MD[0..7]
WE
CCD_ON
RAMUDM
AF_LED
BAT_LOAD
FA20
AFERST
RAMLDQS
FOCUS_PI
ALE
SW_WIDE
IN1A
MS_CLK
SCLK
LCD_EN
SHUT1
SPKRN
PWR_KEY
MS_INS#
LCD_SDATA
SW_TELE
SW_KEY_ADC
SW_PLAYBACK
BAUP_PW
SDATA
+2.5VD
CCD[0..11]
A/V_DET
LENS_SCLK
LCD_SCLK
+3.3VS
ZOOM_PI
ZOOM_M1
CLE
R/B
MODE_KEY_ADC
FLASH_CHG_L
STROBE_CHG
STROBE_TRG
VP_STROBE
DGND
FLASH_RDY
AF_LED
STA_LED
CCD_ON
V4~V15
SUB_CONT
LCD 2.5''
INCH
PANEL
LCD_BACKLIGHT


MEMORY
STICK


J-08 LENS BLOCK
 
 
 
 
 
 
68
2+
SPEAKER

Strobe
modul e
DDR
DGND
+2.5VD
RAMD[0..15]
RAMA[0..14]
RAMLDM
RAMWE_N
RAMCAS
RAMRAS
RAMCS_N
RAMLDQS
RAMUDQS
RAMUDM
RAMCLK_N
RAMCLK
RAMCLK_EN
RAMREF
MEMORY NAND
MD[0..7]
CLE
WE
WP
ALE
CE0
RE
R/B
+3.1VD
DGND
SW
+3.1VD
DGND
SW_KEY_ADC
SW_WIDE
SW_TELE
SW_PLAYBACK_K
MODE_KEY_ADC
1 2
GREENGREEN
POWER
CCD_ON
-7.5V
+3.3V
VP
+5VM
BL-
+15V
BL+
PWR_CTRL
+3.1VD
+2.5VD
+1.8VD
CARD_ON
+3.1VC
+3.3VS
12
REDRED
STROBE
FLASH_CHG_L
STROBE_CHG
STRBOE_TRG
VP_STROBE
DGND
FLASH_RDY
AF_LED
TOP
PWR_KEY
SHUT1
SHUT2
PW_LED
+3.1VD
DGND
DSP
DSP
AFERST
CCD[0..11]
PXCLK
SCLK
SDATA
CDS_CLK
VD
TG_CS
HD
RAMD[0..15]
RAMREF
RAMA[0..14]
RAMCLK_EN
RAMLDQS
RAMWE_N
RAMCS_N
RAMRAS
RAMCAS
RAMLDM
RAMUDM
LENS_EN
STROBE_CHG
SHUTTER_M0
SHUTTER_M1
LENS_SCLK
LENS_SDATA
LENS_PS
TED_BSU
-D+D
PWR_CTRL
STROBE_TRG
PWR_ON
LCD_HD
LCD_VD
LCD_SDATA
LCD_EN
LCD_SCLK
LCD_MCLK
TUO_ENIL TUO_OEDIV
FLASH_CHG_L
VP
DGND
+1.8VD
+3.1VD
+2.5VD
+3.3VS
ZOOM_PI
FOCUS_PI
ZOOM_PR
STA_LED
ZOOM_M0
ZOOM_M1
BAT_LOAD
CE0
TED_VA
#SNI_SM
PW_LED
SW_TELE
SW_WIDE
ALE
CLE
WP
R/B
MD[0..7]
RE
WE
12AF 22AF 02AF
32AF
KLC_SM
SW_KEY_ADC
CCD_ON
TG_ON
CCD_ON
SW_PLAYBACK
SHUT1
SHUT2
AF_LED
RAMUDQS
RAMCLK
RAMCLK_N
IN3A
IN3B
IN2A
IN2B
BKUP_PW
IN1A
IN1B
SPKRN
SPKRP
LCD_D[0..7]
BAT_LEVEL
PWROFF_DET
CARD_ON
BL
PW_KEY
MODE_KEY_ADC
VP_STROBE
FLASH_RDY
AF_LED
12
GREENGREEN
1
2
4
1
3
2
CCD
-7.5V
+15V
JACK
JACK
D+
D-
USB_DET
DGND
A/V_DET
VIDEO_OUT
LINE_OUT
+3.1VD
LCD
+3.1VD
DGND
LCD_EN
LCD_MCLK
LCD_VD
LCD_HD
LCD_SCLK
LCD_SDATA
LCD_D[0..7]
BL
MS
MS_INS#
FA20
FA21
MS_CLK
FA22
FA23
ALE
+3.1VC
DGND
CDS
CDS
+13V
CCD_ON
DGND
TG_ON
CCD[0..11]
PXCLK
VD
HD
AFERST
TG_CS
SCLK
SDATA
-7.5V
+2.5VD
CCD_CLK
1 2
LENS
LENS
LENS_PS
SHUTTER_M1
SHUTTER_M0
ZOOM_M1
ZOOM_M0
LENS_EN
LENS_SCLK
LENS_SDATA
+5VM
+3.1VD
ZOOM_PI
FOCUS_PI
ZOOM_PR
DGND
IN3A
IN3B
IN2A
IN2B
IN1A
IN1B
AF_LED
SPKRN
SPKRP
1 2
GREENGREEN

4. REPAIR PARTS LIST
4-1. EXPLODEDVIEWS
4-1-1. OVERALL SECTION
ns:not supplied
4-1
DSC-S780
Ref. No. Part No. Description Ref. No. Part No. Description
1X-2190-117-1 CABINET (FRONT) ASSY
23-295-133-01 SCREW_TP_1.7_3_A_0.4_D=3
33-295-131-01 SCREW_TP_1.7_7.5_A_0.5_D=2.5
43-295-134-01 SCREW_TP_1.7_3.5_A_0.4_D=3
53-286-713-01 MIDDLE COVER L
63-286-712-01 COVER, JACK
73-286-718-01 BLOCK, RL
8 3-286-719-01 FFC2 (RL)
9 3-286-720-01 LCD (Note)
10 3-874-572-01 SCREW_TP_1.7_2.7_A_0.4_D=3
11 3-295-132-01 SCREW_TP_1.7_2_A_0.4_D=3
12 3-286-714-01 MIDDLE COVER R
12
3
24
4
4
2
12
11
10
8
7
2
6
5
Main Frame Block
(See page 4-2)
Cabinet (Rear) Block
(See page 4-3)
9
(Note)
ns 2
2
11
2
Note : The adjustment is not required after replacing the LCD.

Note 1 : In case of the main board or main frame assy failure,
contact your local Sony service Headquarter for the
measures.
Note 2 : The adjustment is not required after replacing the
ST block assy.
Note 3 : Refer to "Regarding Fuse and etc." for the installation
position of Q13.
ns
(Note 1)
51
55
53
54
53
Lens Block
(See page 4-4)
Q13
(Note 3)
56
F2
F1
ns
(Note 1)
52
(Note 2)
Q1
4-1-2. MAIN FRAME BLOCK
4. REPAIR PARTS LIST
ns:not supplied
4-2
DSC-S780
Ref. No. Part No. Description
51 3-286-725-01 LID, BT
52 A-1444-060-A ST BLOCK ASSY (Note 2)
53 3-295-130-01 SCREW_TP_1.4_3_A_0.3_D=2.5
54 3-295-134-01 SCREW_TP_1.7_3.5_A_0.4_D=3
55 3-874-570-01 SHEET METAL, SP
• Refer to cover for mark .
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.07
• Items marked “*” are not stocked since they are seldom required for
routine service. Some delay should be anticipated when or
dering these items.
Ref. No. Part No. Description
MULTI CONNECTOR (REC) 8P
F1 1-576-363-11
56 1-820-333-11 FUSE, MICRO (1005 TYPE) (1A/30V)
F2 1-576-913-11 FUSE, MICRO (1608 TYPE) (1.6A/36V)
Q1 4-107-819-01 TRANSISTOR FLASH STROBOSCOPE
Q13 4-120-071-01 TRANSISTOR DTC144WM3T5G
*

4-1-3. CABINET (REAR) BLOCK
4. REPAIR PARTS LIST
4-3
DSC-S780
Ref. No. Part No. Description
101 3-295-130-01 SCREW_TP_1.4_3_A_0.3_D=2.5
A-1444-059-A SW BLOCK ASSY
3-286-717-01 FFC1 (SW)
104 3-286-716-01 DIAL, MODE
BUTTON, SW
105
103
102
3-398-568-01
106 X-2190-118-1 CABINET (REAR) ASSY
101
102
103
104
106
105
101

151
152
153
ns
(CCD Assy)
(Note) ns
ns
(TP1.4X3)
ns
(TP1.4X3)
Note : In case of the CCD assy failure, contact your local Sony
service Headquarter for the measures.
4-1-4. LENS BLOCK
4. REPAIR PARTS LIST
4-4
DSC-S780
Ref. No. Part No. Description
151 A-1557-161-A LENS BLOCK ASSY (SERVICE)
4-110-079-01 FILTER SET, LOW PASS
4-110-078-01 SHEET, BLOCK ASSY PROTECTION
153
152
Ver. 1.1 2008.07
ns : not supplied

4. REPAIR PARTS LIST
4-5
Dedicated A/V cable
3-196-980-01
Wrist strap
2-050-981-01
Battery charger BC-CSK
1-480-527-11 (US, CND)
1-480-527-21 (EXCEPT US, CND)
Conversion adaptor
Dedicated USB cable
3-196-981-01
Note 1: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
CD-ROM
(Cyber-shot application software/
"Cyber-shot Handbook"/
"Cyber-shot Step-up Guide")
 3-285-743-51 (POLISH)
 3-285-743-61 (CZECH)
 3-285-743-71 (HUNGARIAN)
 3-285-743-81 (SLOVAK)
 3-285-743-91 (SWEDISH)
 3-285-744-11 (FINNISH)
 3-285-744-21 (NORWEGIAN)
 3-285-744-31 (DANISH)
 3-285-744-41 (THAI)
 3-285-744-51 (MALAYSIAN)
 3-285-744-61 (TURKISH)
 3-285-744-71 (GREEK)
 3-285-744-81 (UKRAINIAN)
Instruction Manual
3-285-741-01
Cyber-shot Handbook(PDF)
The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing.
 3-285-745-11 (ENGLISH) (EXCEPT US, AR, KR)
 3-285-745-21 (FRENCH, ITALIAN) (CND, AEP)
  3-285-745-31 (SPANISH, PORTUGUESE) (AEP, AR)
 3-285-745-41 (GERMAN, DUTCH) (AEP)
 3-285-745-51 (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E)
 3-285-745-61 (RUSSIAN, UKRAINIAN) (AEP)
 3-285-745-71 (ARABIC, PERSIAN) (E)
 3-285-745-81 (KOREAN) (KR)
 3-285-745-91 (POLISH, CZECH) (AEP)
 3-285-746-11 (HUNGARIAN, SLOVAK) (AEP)
 3-285-746-21 (SWEDISH, FINNISH) (AEP)
 3-285-746-31 (NORWEGIAN, DANISH) (AEP)
 3-285-746-41 (THAI, MALAYSIAN) (E)
 3-285-746-51 (TURKISH, GREEK) (AEP)
 3-285-746-61 (ENGLISH, SPANISH) (US)
 3-285-742-11 (ENGLISH)
 3-285-742-21 (FRENCH)
 3-285-742-31 (ITALIAN)
 3-285-742-41 (SPANISH)
 3-285-742-51 (PORTUGUESE)
 3-285-742-61 (GERMAN)
 3-285-742-71 (DUTCH)
 3-285-742-81 (TRADITIONAL CHINESE)
 3-285-742-91 (SIMPLIFIED CHINESE)
 3-285-743-11 (RUSSIAN)
 3-285-743-21 (ARABIC)
 3-285-743-31 (PERSIAN)
 3-285-743-41 (KOREAN)
The printed matter is not supplied. If required,
please order it with the part number below.
DSC-S780
NOTE:
Abbreviation
CND : Canadian model
KR : Korea model AR : Argentine model
Refer to cover for mark .
1-569-007-12 (E)
Rechargeable battery pack NP-BK1
(Note1)
Power cord (mains lead)
(not supplied in the USA and Canada)
1-783-952-61 (AR)
1-824-910-71 (AEP, E)
1-832-169-31 (UK)
1-833-892-21 (KR)
Checking supplied accessories.
4-2. ACCESSORIES

F1
F2
Q13
Ref. No. : F2
MAIN BOARD
【 Regarding Fuse and etc. 】
・
Part No. : 1-576-913-11
Description : FUSE, MICRO (1608 TYPE) (1.6A/36V)
Ref. No. : F1
Part No. : 1-576-363-11
Description : FUSE, MICRO (1005 TYPE) (1A/30V)
Q13 4-120-071-01 DTC144WM3T5G
DSC-S780
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.07

DSC-S780
Revision History
Reverse
Ver.
1.0
Date
2008.03
History
Official Release
Contents
—
S.M. Rev.
issued
—
985228912.pdf
1.1 2008.07 Revised-1 • Addition of DISASSEMBLY for Lens Assy
• Addition of HELP
• Addition of REPAIR PARTS LIST
• Revision of Regarding Fuse
S.M. Revised : Page 4, 2-2, HELP, 4-2, 4-4,
Regarding Fuse and etc.
Yes