Sony DSC-S85 User manual

SERVICE MANUAL
DIGITAL STILL CAMERA
DSC-S85
Level 2
Ver 1.1 2001. 08
Differences Manual
This Service Manual covers only differences from
DSC-S75 (Level 2).
In performing repair, refer to DSC-S75 Service
Manual (Level 2) (9-929-891-32) as well as this manual.
•Main differences:
CCD imager changed
(3.4 M pixels t4.0 M pixels)
(SEE PAGE ss):Pages on the original service manual.
<SEE PAGE ss>:Pages on this service manual.
&: Points added parts.
!: Points deleted parts.
-: Points changed parts.
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Tourist Model
Japanese Model

– 2 –
SPECIFICATIONS
System
Image device
8.98 mm (1/1.8 type)
color CCD
Lens
3×zoom lens
f = 7 – 21 mm (9/32 – 27/32
inches)
(34 – 102 mm (1 3/8 – 4 1/8
inches) when converted into a
35 mm still camera)
F = 2.0 – 2.5
Exposure control
Automatic exposure, Shutter
speed priority, Aperture
priority, Manual exposure
White balance
Automatic, Indoor, Outdoor,
One-push
Data system
Movie: MPEG1
Still: JPEG, GIF (in TEXT
mode, Clip Motion), TIFF
Audio with still image:
MPEG1 (Monaural)
Recording medium
“Memory Stick”
Flash
Recommended recording
distance (ISO is set to AUTO):
0.3mto3.0m(117/8inches
to 9 feet 10 1/8 inches)
Output connector
A/V OUT (Monaural)
Minijack
Video: 1 Vp-p, 75 Ω
unbalanced, sync negative
Audio: 327 mV (at a 47 kΩ
load)
Output impedance: 2.2 kΩ
USB jack
mini-B
External flash jack
Minijack
LCD screen
Used LCD panel
4.6 cm (1.8 type) TFT (Thin
Film Transistor active matrix)
drive
Total number of dots
123 200 (560×220) dots
General
Used battery pack
NP-FM50
Power requirements
7.2 V
Power consumption
(during recording)
3.0 W
Operation temperature
0°C to 40°C
(32°F to 104°F)
Storage temperature
–20°C to +60°C
(–4°F to +140°F)
Maximum dimensions
117×71×64 mm
(4 5/8×2 7/8×2 5/8 inches)
(w/h/d)
Mass
Approx. 462 g (1 lb)
(including battery pack NP-
FM50, “Memory Stick,”
shoulder strap and lens cap
etc.)
Built-in microphone
Electretcondensermicrophone
Built-in speaker
Dynamic speaker
AC-L10A/B/C
AC power adaptor
Power requirements
100 to 240 V AC, 50/60 Hz
Rated output voltage
DC 8.4 V, 1.5 A in operating
mode
Operation temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
–20°C to +60°C
(–4°F to +140°F )
Maximum dimensions
125×39×62 mm
(5×19/16×2 1/2 inches)
(w/h/d)
Mass
Approx. 280 g (10 oz)
NP-FM50 battery pack
Used battery
Lithium ion battery
Maximum voltage
DC 8.4 V
Nominal voltage
DC 7.2 V
Capacity
8.5 Wh (1 180 mAh)
Accessories
A/V connecting cable (1)
NP-FM50 battery pack (1)
AC-L10A AC power adaptor
(1)
Power cord (1)
USB cable (1)
Lens cap (1)
Lens cap strap (1)
Shoulder strap (1)
“Memory Stick” (16 MB)
(1)
CD-ROM (USB driver SPVD-
004) (1)
Operating Instructions (1)
Design and specifications are
subject to change without
notice.

– 3 –
5. ADJUSTMENTS
5-1. Camera Section Adjustment ............................................ 4
1-2. Initialization of B, D, E, F, 7, 9 Page Data ........................ 4
1-2-1. Initialization of D Page Data ....................................... 4
1. Initializing D Page Data............................................... 4
1-2-2. Initialization of B, E, F, 7, 9 Page Data ....................... 4
1. Initializing B, E, F, 7, 9 Page Data .............................. 4
5. F Page Table................................................................ 4
1-4. Camera System Adjustments .......................................... 6
1. Flange Back Adjustment (Using the Minipattern Box)..... 7
2. Flange Back Adjustment
(Using the Flange Back Adjustment Chart) ..................... 8
3. Flange Back Check .......................................................... 9
4. Picture Frame Setting....................................................... 10
5. F No.Standard Data Input ............................................... 11
6. Mechanical Shutter Adjustment ....................................... 11
7. Light Level Adjustment..................................................... 12
8. Mixed Color Cancel Adjustment....................................... 12
9. Auto White Balance Standard Data Input ........................ 13
10. Auto White Balance Adjustment ...................................... 14
11. Smear Compensation Adjustment ................................... 15
12. Color Reproduction Adjustment ....................................... 16
13. Color Reproduction Check ............................................... 17
14. Auto White Balance Check............................................... 18
15. CCD White Defect Compensation ................................... 19
16. CCD Black Defect Compensation.................................... 20
17. Strobe White Balance Adjustment ................................... 21
6. REPAIR PARTS LIST
6-1. Exploded Views ................................................................ 22
6-1-1. Main Section................................................................ 22
6-1-2. Cabinet (Front) Block Assembly ................................. 22
6-1-3. Lens Block Assembly .................................................. 22
6-1-4. Cabinet (Rear) Block Assembly.................................. 22
6-2. Electrical Parts List .......................................................... 23
TABLE OF CONTENTS
Section Title Page
Ver. 1.1 2001. 08

– 4 –
5-1. CAMERA SECTION ADJUSTMENT
1-2. INITIALIZATION OF B, D,E, F,7,9 PAGE DATA
1-2-1. Initialization of D Page Data
1. Initializing D Page Data
Note: If the D page data has been initialized, the following
adjustments need to be performed again.
1) Modification of D page data
2) LCD system adjustments
Adjusting page D
Adjusting Address 10 to EF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01
24 030A
34 002D
4 4 01 2D Press PAUSE button.
5 4 02 Checkthedata changes to “01”.
6Perform “Modification of D
page Data”.
Address Initial value Remark
10 to 13 Fixed data-1 (Initialized data)
14 33
15 48
16 DA
17 DF
18 13
19 C0
1A 00
1B 00
1C 00
1D 00 Flange back adj.
1E 00
1F 00
20 20
21 20
22 BA
23 46
24 0A
25 00
26 85
27 B0 Light level adj.
28 94
29 00
2A 00
2B 00 F No. standard data input
2C 00
2D 00
2E to 39 Fixed data-1 (Initialized data)
3A 2F
3B 37 Auto white balance standard data
3C 40 input
3D D0
3E Fixed data-1 (Initialized data)
3F B5 Auto white balance adj.
40 43
41 03
42 E9
43 63
44 83
45 D5 Color reproduction adj.
46 FE
47 73
48 45
SECTION 5
ADJUSTMENTS
DSC-S85 Ver. 1.1 2001. 08
5. F Page Table
Note 1: Fixed data-1: Initialized data.
(Refer to “1.Initializing of B, E, F, 7, 9 Page Data”)
Note 2: Fixed data-2: Modified data.
(Refer to “2.Modification of B, E, F, 7, 9 Page Data”)
1-2-2. Initialization of B, E, F, 7, 9 Page Data
1. Initializing B, E, F, 7, 9 Page Data
Note: If the B, E, F, 7, 9 Page data has been initialized,
“Modification of B, E, F, 7, 9 Page Data” and following
adjustments need to be performed again.
1) Modification of B, E, F, 7, 9 page data
2) Video system adjustments
3) Camera system adjustments
Adjusting page F
Adjusting Address 10 to FF
Adjusting page E
Adjusting Address 00 to FF
Adjusting page B
Adjusting Address 00 to FF
Adjusting page 7
Adjusting Address 00 to FF
Adjusting page 9
Adjusting Address 00 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01
26 030A
36 002D
4 6 01 2D Press PAUSE button.
5 6 02 Checkthedata changes to “01”.
6Perform “Modification of B,
E, F, 7, 9 page Data”.

– 5 –
Address Initial value Remark
8B 00
8C 00
8D 00
8E 00
8F 00
90 00
91 00
92 00
93 00 Flange back adj.
94 00
95 00
96 00
97 00
98 00
99 00
9A 00
9B 00
9C Fixed data-1 (Initialized data)
9D 16 Smear compensation adj.
9E 1C
9F Fixed data-1 (Initialized data)
A0 00
A1 00
A2 00 Mixed color cancel adj.
A3 00
A4 to A8 Fixed data-1 (Initialized data)
A9 2C Auto white balance adj.
AA 06
AB to D3 Fixed data-1 (Initialized data)
D4 80
D5 9E
D6 94 Mechanical shutter adj.
D7 94
D8 94
D9 to FF Fixed data-1 (Initialized data)
Address Initial value Remark
49 to 4C Fixed data-1 (Initialized data)
4D 28 Strobe white balance adj.
4E 6E
4F to 58 Fixed data-1 (Initialized data)
59 00 Auto white balance standard data input
5A 14 Mechanical shutter adj.
5B Fixed data-1 (Initialized data)
5C 63
5D 83 Color reproduction adj.
5E 03
5F E9
60 to 63 Fixed data-1 (Initialized data)
64 10 Strobe white balance adj.
65 to 68 Fixed data-1 (Initialized data)
69 02
6A 79 Strobe white balance adj.
6B F8
6C 10
6D 05
6E 09
6F B5
70 07
71 C4
72 07
73 48
74 06
75 CB Mechanical shutter adj.
76 01
77 01
78 01
79 01
7A 01
7B 2C
7C 3A
7D 2E
7E 40
7F 40
80 00 Auto white balance adj.
81 to 86 Fixed data-1 (Initialized data)
87 FF
88 00 Flange back adj.
89 00
8A 00
Ver. 1.1 2001. 08

– 6 –
1-4. CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEMADJUSTMENTS” are sat-
isfied.
Note: For “CAMERA SYSTEM ADJUSTMENTS”, perform in
order of item numbers.
Data setting during camera system adjustments
Perform the following data setting before the camera system ad-
justments.
Menu setting:
1) VIDEO OUT of SET UP menu................ NTSC (NTSC mode)
(This adjustment must be performed in NTSC mode, so don't
set the menu setting to “PAL”)
Data setting method:
Order Page Address Data Procedure
1 0 01 01
2 D 10 80 Press PAUSE button.
32 10 Check the bit values of bit3,
bit4 and bit5 are “1”.
(Note 1, 2)
4 D 11 40 Press PAUSE button.
5 D 10 81 Press PAUSE button.
56 C1 Check the data changes to
“02”.
6 4 06 01
76 6C01
8 Wait for 1 second.
9 B 75 00 Press PAUSE button.
Note 1: For the bit values, refer to “5-2. SERVICE MODE”,
“2-3. 2. Bit value discrimination”.
Note 2: In case of wrong data, select page: 2, address: 0A and set
data: 02.
Set the adjusting remote commander to normal LANC,
and the power will be turned off and on automatically.
Wait for more than 0.167 second after the power on, and
set the adjusting remote commander to the service LANC.
Then, retry from the step 1.
Note 3: Repeat the “Data setting method”, if the power was turned
off and on during the “CAMERA SYSTEM ADJUST-
MENTS”.
After completing the camera system adjustments,
release the data setting:
Order Page Address Data Procedure
1 4 06 00
26 6C00
3 B 75 10 Press PAUSE button.
4 D 11 00 Press PAUSE button.
5 D 10 00 Press PAUSE button.
6 0 01 00
Ver. 1.1 2001. 08

– 7 –
1. Flange Back Adjustment (Using the minipattern box)
The flange back of inner focus lens is adjusted automatically. If
shifted, the auto focus is disordered.
Mode CAMERA
Subject Siemens star chart with ND filter
for minipattern box (Note 1)
Measurement Point Check operation on the LCD
Measuring Instrument screen
Adjustment Page F
Adjustment Address 14 to 25, 87 to 9B
Note 1: Dark Siemens star chart.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Preparations before adjustments:
1) The minipattern box is installed as shown in the following fig-
ure.
Note 3: The attachment lenses are not used.
Note 4: Take care not to hit the mini-pattern box when
extending the lens.
2) Install the minipattern box so that the distance between it and
the front of lens of camera is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the
specified voltage ± 0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of
shot image screen with the zoom lens at TELE end and WIDE
end respectively.
6) Check that the data on page: F, address: 14 to 25 and 87 to 9B
are initial value (See table below).
Specified voltage: The specified voltage varies according to the
minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the mini-
pattern box.
Minipattern box
Below 3 cm
Camera
Camera
table
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage :Specified voltage ±0.01 Vdc
Output current : more than 3.5 A
Fig. 5-1-13
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
3 6 01 13 Press PAUSE button.
4 6 01 27 Press PAUSE button. (Note 5)
5 6 02 Check the data changes to “01”.
6 F 87 Checkthedatachanges to “00”.
Note 5: The adjustment data will be automatically input to page:
F, address: 14 to 25 and 87 to 9B.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
2Release the data setting
performed at step 2. (Refer to
page 5-14)
3 0 01 00
4 Perform“Flange Back Check”.
Address Data Address Data Address Data
14 33 21 20 8F 00
15 48 22 BA 90 00
16 DA 23 46 91 00
17 DF 24 0A 92 00
18 13 25 00 93 00
19 C0 87 FF 94 00
1A 00 88 00 95 00
1B 00 89 00 96 00
1C 00 8A 00 97 00
1D 00 8B 00 98 00
1E 00 8C 00 99 00
1F 00 8D 00 9A 00
20 20 8E 00 9B 00

– 8 –
2. Flange Back Adjustment
(Using the flange back adjustment chart)
The flange back of inner focus lens is adjusted automatically. If
shifted, the auto focus is disordered.
Mode CAMERA
Subject Flange back adjustment chart
(2.0 m from the front of the lens)
(Luminance: 300 to 400 lux)
Measurement Point Check operation on the LCD
Measuring Instrument screen
Adjustment Page F
Adjustment Address 14 to 25, 87 to 9B
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front
of the lens.
2) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.
3) Check that the data on page: F, address: 14 to 25 and 87 to 9B
are initial value (See table below).
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
3 6 01 13 Press PAUSE button.
4 6 01 15 Press PAUSE button. (Note 2)
5 6 02 Checkthedatachangesto “01”.
6 F 87 Check thedatachangesto“00”.
Note 2: The adjustment data will be automatically input to
page: F, address: 14 to 25 and 87 to 9B.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
2Release the data setting
performed at step 2.
(Refer to page 5-14)
3 0 01 00
4 Perform“Flange Back Check”.
Address Data Address Data Address Data
14 33 21 20 8F 00
15 48 22 BA 90 00
16 DA 23 46 91 00
17 DF 24 0A 92 00
18 13 25 00 93 00
19 C0 87 FF 94 00
1A 00 88 00 95 00
1B 00 89 00 96 00
1C 00 8A 00 97 00
1D 00 8B 00 98 00
1E 00 8C 00 99 00
1F 00 8D 00 9A 00
20 20 8E 00 9B 00

– 9 –
3. Flange Back Check
Mode CAMERA
Subject Siemens star chart
(1.0 m from the front of the lens)
(Luminance: 200 to 400 lux)
Measurement Point Check operation on the LCD
Measuring Instrument screen
Specified value Focused at the TELE end and
WIDE end
Checking method:
Order Page Address Data Procedure
1
Place the Siemens star 1.0 m
from the front of the lens.
To open the IRIS , decrease
the luminous intensity to the
Siemens star up to a point
before noise appear on the
image.
2 0 01 01
3Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
4
Shoot the Siemens star chart
with the zoom TELE end.
At this time, the center of
Siemens star chart should be
in the center of the LCD
screen.
5Check that the lens is
focused.
66 2C01
7
While observe the LCD
screen, change the zoom to
the WIDE end and check that
the lens is focused.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
16 2C00
2Release the data setting
performed at step 3.
(Refer to page 5-14)
3 0 01 00

– 10 –
How to reset the zoom and focus when they deviated:
Order Page Address Data Procedure
16 2C01
2 6 90 00
3 6 91 00
4 6 92 YL (Note 2)
5 6 93 YH (Note 2)
6 6 01 79 Press PAUSE button.
7 6 07 Check the data changes to “01”.
8 6 01 00 Press PAUSE button.
Note 2: The data noted down at step 9 of “Setting method”.
Check on the oscilloscope
1. Horizontal period
Fig. 5-1-14
2. Vertical period
Fig. 5-1-15
Check on theTV monitor
Fig. 5-1-16
4. Picture Frame Setting
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Measurement Point Video terminal of A/V OUT jack
(75 Ωterminated)
Measuring Instrument Oscilloscope and TV monitor
Specified Value A=B, C=D, E=F
Note 1: Displayed data of the page 1 of adjusting remote com-
mander.
1:XX:XX YL data
YH data
Switch setting:
1) FOCUS ............................................... AF (AUTO FOCUS)
Setting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
3Shoot the color bar chart
with the zoom WIDE end.
4
Enter the output of VIDEO
OUT to the TV monitor, and
move to the position as
shown in Fig. 5-1-16.
5
Horizontal width of one
color (B, C) and that of black
(A, D) on the color bar chart
should be same. (See Fig. 5-
1-14)
6
With vertical width of black
(E, F) set in same, the color
bar chart should come to the
center of TV monitor.
(See Fig. 5-1-15)
7Check that the color bar on
the TV monitor is focused.
8 0 03 22
91 Note down the YH andYL
data. (Note 1)
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 0 03 00
2Release the data setting
performed at step 2 .
(Refer to page 5-14)
3 0 01 00
A=B C=D
A
BC
D
Color bar chart picture frame TV monitor
p
icture frame
E=F
V
EF

– 11 –
6. Mechanical Shutter Adjustment
Adjust the period which the mechanical shutter is closed, and com-
pensate the exposure.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at WIDE
end)
Adjustment Page F
Adjustment Address 5A, 6C to 7F, D4 to D8
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 AD Press PAUSE button. (Note 3)
12 6 02 Check the data changes to “01”.
13 6 AB Check the data changes to “00”.
Note 3: The adjustment data will be automatically input to page:
F, address: 5A, 6C to 7F and D4 to D8.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 92 00
4 6 93 00
5Release the data setting
performed at step 2 .
(Refer to page 5-14)
6 0 01 00
5. F No. Standard Data Input
Compensate the unevenness of the iris meter sensitivity.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at WIDE
end)
Adjustment Page F
Adjustment Address 29 to 2D
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 BB Press PAUSE button. (Note 3)
12 6 02 Check the data changes to “01”.
Note 3: The adjustment data will be automatically input to page:
F, address: 29 to 2D.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 92 00
4 6 93 00
5Release the data setting
performed at step 2 .
(Refer to page 5-14)
6 0 01 00

– 12 –
7. Light Level Adjustment
Adjust the standard LV value.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Measurement Point Displayed data of page: 1 (Note 3)
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 26 to 28
Specified Value AE level: 0FC0 to 1040
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of the unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: The right 4 digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX
 Displayed data
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 0D Press PAUSE button. (Note 4)
12 6 02 Check the data changes to “01”.
13 0 03 06
14 1
Check that the displayed data
(Note 3)
satisfies theAE level
specified value.
Note 4: The adjustment data will be automatically input to
page: F, address: 26 to 28.
Processing after Completing Adjustment:
Order Page Address Data Procedure
1 0 03 00
2 6 01 00 Press PAUSE button.
36 2C00
4 6 92 00
5 6 93 00
6Release the data setting performed atstep 2 .
(Refer to page 5-14)
7 0 01 00
8. Mixed Color Cancel Adjustment
To perform mixed color cancel adjustment based on data of each
color in color bar.
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Adjustment Page F
Adjustment Address A0 to A3
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of the unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 D7 Press PAUSE button.
12 6 01 D5 Press PAUSE button. (Note 3)
13 6 02 Check the data changes to “01”.
Note 3: The adjustment data will be automatically input to
page: F, address: A0 to A3.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 92 00
4 6 93 00
5Release the data setting
performed at step 2 . (Refer
to page 5-14)
6 0 01 00
Ver. 1.1 2001. 08

– 13 –
9. AutoWhite Balance Standard Data Input
Adjust the white balance standard data at 3200K.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Adjustment Page F
Adjustment Address 3A to 3D, 59
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: “Auto White Balance Standard Data Input” is available
only once after the power is turned on. Turn the power
off, then on again if the adjustment is retried.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 11 Press PAUSE button.
12 6 01 0B Press PAUSE button. (Note 4)
13 6 02 Check the data changes to “01”.
Note 4: The adjustment data will be automatically input to
page: F, address: 3A to 3D and 59.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 92 00
4 6 93 00
5Release the data setting
performed at step 2 .
(Refer to page 5-14)
6 0 01 00

– 14 –
Order Page Address Data Procedure
19 1
Check that the displayed data
(Note 3)
satisfies the R ratio specified
value.
20 0 03 05
21 1
Check that the displayed data
(Note 3)
satisfies the B ratio specified
value.
22 6 01 00 Press PAUSE button.
23 6 01 11 Press PAUSE button.
24 6 13 AE Press PAUSE button.
25 6 01 D3 Press PAUSE button.
26 6 02 Check the data changes to “01”.
Note 5: The adjustment data will be automatically input to
page: F, address: 3F, 40, 80, A9 and AA.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 0 03 00
2 6 01 00 Press PAUSE button.
3 6 13 00 Press PAUSE button.
46 2C00
5 6 92 00
6 6 93 00
7F
49 Set the data noted down at
4A step 13, and press PAUSE
4B button.
4C
8Release the data setting
performed at step 3 .
(Refer to page 5-14)
9 0 01 00
10 Remove the C14 filter on the
lens.
10. AutoWhite Balance Adjustment
Adjust to the proper auto white balance output data. If it is not
correct, auto white balance and color reproducibility will be poor.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Filter Filter C14 for color temperature
correction
Measurement Point Displayed data of page: 1 (Note 3)
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 3F, 40, 80, A9, AA
Specified Value R ratio: 28E0 to 2A20
B ratio: 5D60 to 5EA0
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: The right 4 digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX Displayed data
Note 4: “Auto White BalanceAdjustment” is available only once
after the power is turned on. Turn the power off, then on
again if the adjustment is retried.
Adjusting method:
Order Page Address Data Procedure
1 Place the C14 filter on the lens.
2 0 01 01
3Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
46 2C01
5 6 90 00
6 6 91 00
7 6 92 YL (Note 2)
8 6 93 YH (Note 2)
9 6 01 79 Press PAUSE button.
10 6 07 Check the data changes to “01”.
11 6 01 00 Press PAUSE button.
12 6 01 A7 Press PAUSE button.
13 F
49
Note down the data.
4A
4B
4C
14 F
49 29
Press PAUSE button.
4A 80
4B 5E
4C 00
15 6 01 A5 Press PAUSE button. (Note 5)
16 6 02 Check the data changes to “01”.
17 6 01 3F Press PAUSE button.
18 0 03 04
Ver. 1.1 2001. 08

– 15 –
11.Smear Compensation Adjustment
Adjust the smear compensation data from white balance standard
data at 3200K.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Adjustment Page F
Adjustment Address 9D, 9E
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: “Smear CompensationAdjustment” is available only once
after the power is turned on. Turn the power off, then on
again if the adjustment is retried.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
96 07 Check the data changes to
“01”.
10 6 01 00 Press PAUSE button.
11 6 01 11 Press PAUSE button.
12 6 13 AE Press PAUSE button.
13 6 01 D1 Press PAUSE button. (Note 4)
14 6 02 Check the data changes to “01”.
Note 4: The adjustment data will be automatically input to
page: F, address: 9D and 9E.
Processing after Completing Adjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
2 6 13 00 Press PAUSE button.
36 2C00
4 6 92 00
5 6 93 00
6Release the data setting performed at step 2. (Refer to
page 5-14)
7 0 01 00

– 16 –
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 92 00
4 6 93 00
5Release the data setting
performed at step 2 .
(Refer to page 5-14)
6 0 01 00
7Perform “Color Reproduc-
tion Check”.
12. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Adjustment Page F
Adjustment Address 41 to 48, 5C to 5F
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of the unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: “Color Reproduction Adjustment” is available only once
after the power is turned on. Turn the power off, then on
again if the adjustment is retried.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 01 AB Press PAUSE button.
12 6 12 80
13 Wait for 1 second.
14 6 12 00
15 Wait for 2 seconds.
16 6 01 A9 Press PAUSE button. (Note 4)
17 6 02 Check the data changes to “01”.
Note 4: The adjustment data will be automatically input to
page: F, address: 41 to 48 and 5C to 5F.
Ver. 1.1 2001. 08

– 17 –
13. Color Reproduction Check
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Measurement Point Video terminal of A/V OUT jack
(75 Ωterminated)
Measuring Instrument Vectorscope
Specified Value All color luminance points
should settle within each color
reproduction frame.
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of the unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
36 2C01
4 6 90 00
5 6 91 00
6 6 92 YL (Note 2)
7 6 93 YH (Note 2)
8 6 01 79 Press PAUSE button.
9 6 07 Check the data changes to “01”.
10 6 01 00 Press PAUSE button.
11 6 10 01
12 E 52 Note down the data.
13 E 52 09 Press PAUSE button.
14 6 01 0F Press PAUSE button.
15 6 12 80
16 Wait for 1 second.
17 6 12 00
18 Wait for 2 seconds.
19 Check the each color
luminance point is in each
color reproduction frame.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
2 6 10 00
36 2C00
4 6 92 00
5 6 93 00
6E 52 Set the data noted down at
step 12, and press PAUSE
button.
7Release the data setting
performed at step 2 . (Refer
to page 5-14)
8 0 01 00
Fig. 5-1-17
R-Y
B-Y
R
B
G
MG
YE
CY
Burst position
Ver. 1.1 2001. 08

– 18 –
14. AutoWhite Balance Check
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame with the zoom lens at
WIDE end)
Measurement Point Displayed data of Video terminal
of Page: 1 A/V OUT jack
(Note 3) (75 Ωterminated)
Measuring Instrument Adjusting remote Vectorscope
commander
Specified Value R ratio: Fig. 5-1-18
3E00 to 4200 (A) and (B)
B ratio:
3E00 to 4200
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Refer to “Picture Frame Setting” forYH andYL.
Note 3: The right 4 digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX Displayed data
Checking method:
Order Page Address Data Procedure
1Check that the lens is not
covered with either filter.
2 0 01 01
3Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
46 2C01
5 6 90 00
6 6 91 00
7 6 92 YL (Note 2)
8 6 93 YH (Note 2)
9 6 01 79 Press PAUSE button.
10 6 07 Check the data changes to “01”.
11 6 01 00 Press PAUSE button.
INDOOR data check (without ND filter)
12 E 52 Note down the data.
13 E 52 0E Press PAUSE button.
14 6 01 0F Press PAUSE button.
15 0 03 04
16 1
Check that the displayed data
(Note 3) satisfied the R ratio
specified value.
17 0 03 05
18 1
Check that the displayed data
(Note 3) satisfied the B ratio
specified value.
INDOOR luminance point check
19
Check that the center of the
white luminance point within
the circle shown
Fig. 5-1-18 (A).
OUTDOOR luminance check
20 Place the C14 filter on the
lens.
21 E 4B Note down the data.
22 E 4B 20 Press PAUSE button.
23 6 01 3F Press PAUSE button.
24
Check that the center of the
white luminance point settles
in the circle shown
Fig. 5-1-18 (B).
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 0 03 00
2 6 01 00 Press PAUSE button.
36 2C00
4 6 92 00
5 6 93 00
6E 4B Set the data noted down at
step 21, and press PAUSE
button.
7E 52 Set the data noted down at
step 12, and press PAUSE
button.
8
Release the data setting
performed at step 3 .
(Refer to page 5-14)
9 0 01 00
10 Remove the C14 filter on the
lens.
R-Y
B-Y
4 mm
4 mm
Fig. 5-1-18 (A)
Fig. 5-1-18 (B)
R-Y
B-Y
1.5 mm
1 mm
6 mm
6 mm
Ver. 1.1 2001. 08

– 19 –
15. CCD White Defect Compensation
Mode CAMERA
Subject Not required
Measurement Point Displayed data of page: 6,
address: 55
Measuring Instrument Adjusting remote commander
Adjustment Page 7
Adjustment Address 88 to A3
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
3 F DE Note down the data.
4 F DE 1E Press PAUSE button.
5 F E3 Note down the data.
6 F E3 0E Press PAUSE button.
7 6 01 8B Press PAUSE button. (Note 2)
8 6 02 Check the data changes to “01”.
96 55 Check the data.
00 to 7F: Normal
80 to FF: Defective
10 6 01 00 Press PAUSE button.
11 F DE 0F Press PAUSE button.
12 F E3 60 Press PAUSE button.
13 6 01 87 Press PAUSE button.
14 6 02 Check the data changes to “01”.
15 6 55 Check the data changes to “00”.
Note 2: The adjustment data will be automatically input to
page: 7, address: 88 to A3.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
2F E3 Set the data noted down at
step 5, and press PAUSE
button.
3F DE Set the data noted down at
step 3, and press PAUSE
button.
4Release the data setting
performed at step 2 . (Refer
to page 5-14)
5 0 01 00
Ver. 1.1 2001. 08

– 20 –
16. CCD Black Defect Compensation
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment
frame)
Measurement Point Displayed data of page: 6,
address: 55
Measuring Instrument Adjusting remote commander
Adjustment Page 7
Adjustment Address 60 to 87
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 2: Check that there are no dust, no dirt and reflection of the
clear chart.
Note 3: Any subject other than the clear chart should be in the
screen.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2Perform “Data setting during
camera system adjustments”.
(Refer to page 5-14)
3 F DF Note down the data.
4 F DF 4C Press PAUSE button.
56 2C01
6 6 90 00
7 6 91 03
8 6 92 00
9 6 93 00
10 6 01 79 Press PAUSE button.
11 6 30 01
12 6 07 Check the data changes to “01”.
13 6 01 8D Press PAUSE button. (Note 4)
14 6 02 Check the data changes to “01”.
15 6 55 Check the data.
00 to 0A: Normal
0B to FF: Defective
16 6 01 00 Press PAUSE button.
17 F DF 5A Press PAUSE button.
18 6 01 89 Press PAUSE button.
19 6 02 Check the data changes to “01”.
20 6 55 Check the data changes to “00”.
Note 4: The adjustment data will be automatically input to
page: 7, address: 60 to 87.
Processing after CompletingAdjustment:
Order Page Address Data Procedure
1 6 01 00 Press PAUSE button.
26 2C00
3 6 30 00
4 6 91 00
5F DF Set the data noted down at
step 3, and press PAUSE
button.
6Release the data setting
performed at step 2 . (Refer
to page 5-14)
7 0 01 00