Sony PCG-R505TE Primary User manual

Confidential
SERVICE MANUAL
Notebook Computer
US Model
Canadian Model
PCG-R505TE/R505TEK/R505TS/R505TSK
S400
9-872-185-11

– 2 –PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
Informationinthisdocumentissubjectto change withoutnotice.
Sony and VAIO are trademarks of Sony. Microsoft, MS-DOS,
Windows, the Windows 95, Windows 98, Windows 2000 and
Windows ME logo are trademarks of Microsoft Corporation.
All other trademarks are trademarks or registered trademarks of
their respective owners. Other trademarks and trade names may be
used in this document to refer to the entitles claiming the marks and
namesor their produces.Sony Corporationdisclaims any proprietary
interest in trademarks and trade names other than its own.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as
well as all precautions listed in the operating manual and other associated
documents.
2. Use designated parts only
The set’s components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the 0mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3. Always follow the original design when
mounting parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts or
routing wires, therefore, be sure to duplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6. When handling flexible print boards...
•The temperature of the soldering-iron tip should be about 270C.
•Do not apply the tip more than three times to the same pattern.
•Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
CautionMarkings for Lithium/Ion Battery- The followingorsimilar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse charging, multilation
or incineration of the cells must bi avoided to prevent one or
more of the following occurrences; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in surface
temperature.
• If a cell has leaked or vented, it should be replaced
immediately while avoiding to touch it without any protection.

– 3 – PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
TABLE OF CONTENTS
Section Title Page
CHAPTER 1. REMOVAL
1-1. Flowchart ......................................................................... 1-1
1-2. Main Electrical Parts Location Diagram ......................... 1-2
1-3. Removal ........................................................................... 1-2
1. Key Board Unit ................................................................ 1-2
2. Palm Rest Section ............................................................ 1-3
3. SWX-72 Board, Encoder (Rotaly), Touch Pad ................ 1-3
4. IFX-141 Board ................................................................. 1-4
5. Battery.............................................................................. 1-4
6. HDD................................................................................. 1-5
7. Cover (Bottom LF/LR/R) ................................................ 1-5
8. Frame Housing................................................................. 1-6
9. SWX-76 Board, Speaker (L/R)........................................ 1-6
10. CNX-119 Board ............................................................... 1-7
11. Modem Card .................................................................... 1-7
12. CNX-121 Board ............................................................... 1-8
13. DC Fan ............................................................................. 1-8
14. MBX-48 Board ................................................................ 1-9
15. Heatsink (CPU)................................................................ 1-9
16. CNX-120 Board, LCD Section, CNX-131 Board ......... 1-10
17. Bezel .............................................................................. 1-11
18. LCD Unit ....................................................................... 1-11
19. LEX-29 Board, Inverter Unit ......................................... 1-12
(to 1-12)
CHAPTER 2. SELF DIAGNOSTICS.......................... 2-1
Please confirm “Self Diagnostics” method which will be informed
you with distribution of “Self Diagnostics” software.
CHAPTER 3. BLOCK DIAGRAM ............................... 3-1
(to 3-2)
CHAPTER 4. FRAME HARNESS DIAGRAM ........ 4-1
(to 4-2)
CHAPTER 5. EXPLODEDVIEWS AND
PARTS LIST
5-1. Main Section .................................................................... 5-1
5-2. LCD Section .................................................................... 5-3
5-3. Accessories ...................................................................... 5-5
(to 5-5)
• Abbreviations
UC : US model / Canadian model

1-1 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
CHAPTER 1.
REMOVAL
1-1. Flowchart
•P XX means pages that appears in this manual.
•Remember that hard disk drives are easily damaged by vibration. Always handle with care.
POWER
OFF KEY BOARD
UNIT
P 1-2
PALM REST
SECTION
P 1-3
COVER
(BOTTOM LF/
LR/R)
P 1-5
FRAME
HOUSING
P 1-6
SWX-72
BOARD ENCODER
(ROTALY)
IFX-141
BOARD
P 1-3
SWX-76
BOARD
P 1-6
P 1-3
TOUCH
PAD
P 1-3
P 1-6
CNX-119
BOARD
SPEAKER
(L/R)
P 1-7
CNX-121
BOARD
P 1-8
MBX-48
BOARD
P 1-9
HEATSINK
(CPU)
P 1-9
DC
FAN
P 1-8
CNX-120
BOARD
P 1-10
CNX-131
BOARD
P 1-10
LEX-29
BOARD
P 1-12
LCD
SECTION
P 1-10
LCD
UNIT
P 1-11
INVERTER
UNIT
P 1-12
MODEM
CARD
P 1-7
P 1-4
HDD
P 1-5
BEZEL
P 1-11
BATTERY
P 1-4

1-2PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
2Claw
2Claw
2Claw
3
4Harness
Key Board Unit
1M2X6
1-2. Main Electrical Parts Location Diagram
1-3. Removal
1. Key Board Unit
CNX-131 Board
LEX-29 Board
Inverter Unit
Modem Card
SWX-76 Board
Speaker (R)
Speaker (L)
CNX-119 Board
SWX-72 Board
IFX-141 Board
MBX-45 Board
CNX-121 Board
DC Fan
Encoder (Rotaly)
Battery
Touch Pad
HDD
LCD Unit

1-3 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
2. Palm Rest Section
3. SWX-72 Board, Encoder (Rotaly),Touch Pad
3FFC (10P)
Palm Rest Section
1M2X6
1M2X6
2
1FFC (10P)
3M2X4
6
9
4
5M1.4X3.5
7Claw
7Claw 7Claw
7Claw
Touch Pad
2Flexible Flat
Cable (12 core)
8Escutcheon (TP)
SWX-72 Board
Encoder (Rotaly)

1-4PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
4M2X4
1FFC (12P)
2Claw
3Cover (Bottom LF)
IFX-141 Board
5
4. IFX-141 Board
5. Battery
1Harness
Nickel Hydrogen Battery
2

1-5 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
1Claw
3Claw
3Claw
5Claw
Cover
(Bottom LF)
Cover (Bottom LR)
Cover (Bottom R) Assy
2
4
6
6M3X4
2M2X4
4M3X4
1FPC (HDD)
7Bracket (HDD F)
5Bracket (HDD R)
HDD 20 GB
(PCG-R505TSK/R505TS)
HDD 15 GB
(PCG-R505TEK/R505TE/R505DE)
3
6. HDD
7. Cover (Bottom LF/LR/R)

1-6PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
8. Frame Housing
9. SWX-76 Board, Speaker (L/R)
3Undo four claws and
remove the cover (BP).
3Undo four claws and
remove the cover (BP).
4M2X6
Frame Housing
5
1Harness
2FFC (8P)
8Speaker
Bracket
6Speaker Bracket
4Harness
2Tapping
2X4
5Button (Power)
1FFC (8P)
SWX-76 Board
9
3
7
Speaker (L)
Speaker (R)

1-7 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
1M2X2.5
1M2X2.5
4Harness (2P)
3
Modem Card
2Connector
10. CNX-119 Board
11. Modem Card
3FFC (20P) 1M2X4
2
CNX-119 Board

1-8PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
1M2X4
3
4FFC (10P)
CNX-121 Board
2Shield CNX1
DC Fan (With Heatsink)
2M2X6
2M2X6
1Harness
3
12. CNX-121 Board
13. DC Fan

1-9 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
14. MBX-48 Board
15. Heatsink (CPU)
qa Lid (VGA) Assy
4FFC (20P)
7M2X2.5
5M2X4
5M2X4 5M2X4
5M2X4
9
2Harness (Power 3P)
1Harness (LCD)
8Spacer (MBX)
0RJ-45 (For Internal)
Harness
MBX-48 Board
3Harness
6Shield MBX1
1P2X3
2
3Bracket (CPU)
Heatsink (CPU)
*The heatsink (CPU) must be installed
with the thermal sheet (CPU) in soft state to
protect the CPU from the stress.
For this purpose, with the thermal sheet
(CPU) pasted, warm the heatsink (CPU) to
about 70 °C, and when the thermal sheet
(CPU) has become soft, install the heatsink
(CPU) on the main board.

1-10PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
16. CNX-120 Board, LCD Section, CNX-131 Board
8M2X4
5M2X5
1M2X5
6M2X5
7M2X4
0Harness (Power 3P)
qd Cover (BBL)
CNX-131 Board
3Harness (2P)
LCD Section
CNX-120 Board
4Harness
(LCD)
9
2
qa
qs Cover (BBR)

1-11 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
17. Bezel
18. LCD Unit
1Cover (DR)
2Cover (DL)
5Claw
5Claw
5Claw
5Claw
5Claw
6
4M2X5
4M2X5
3Hole Blind (Side)
3Hole Blind (Side)
Housing (Bezel) Assy
6M2X3
4M2X3
7Bracket (LCD-L)
5Bracket (LCD-R)
1Harness
LCD Unit
3Harness (LCD)
2

1-12PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
(END)
19. LEX-29 Board, Inverter Unit
3Harness
5Harness
6Harness
1M2X3 2
4
Inverter Unit
LEX-29 Board

2-1 PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
CHAPTER 2.
SELF DIAGNOSTICS
< ATTENTION >
Please confirm “Self Diagnostics” method which will be informed
you with distribution of“Self Diagnostics” software.
(END)

PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
3-1 3-2
CHAPTER 3.
BLOCK DIAGRAM
(END)
Graphics &Memory
CONTROLLER
HUB
GMCH2-m
Graphics &Memory
CONTROLLER
HUB
GMCH2-m
Bus #0 Dev #0, 1,2
IO Control Hub
ICH2-m
IO Control Hub
ICH2-m
Bus #0 Dev #8,31
i.LINK
PHY &
ATAPI
Bridge
i.LINK
PHY &
ATAPI
Bridge
Internal
HDD
VGA DB-15
Docking Station
USB(B) CONN x1
PHONE
OUT
RJ11
BATTERY
DC-IN
CONN
BAT CONN
POWER
SUPPLY
&
CHARGE
R
1/1
MIC
IN
RJ45
USB
CONN
MS
CONN
Port Connector 100+4pin
Coppermine
Processor Core with 256/
128KB L2 Cache
BGA2
Coppermine
Processor Core with 256/
128KB L2 Cache
µBGA2
PCI BUS(3.3V)
DVO(3.3V)
100MHz Memory Bus
SO-DIMM
PCI-1394
TI
TSB43LV22
PCI-1394
TI
TSB43LV22
Bus #1 Dev #8
CARDBUS
RICOH
RC5C475II
CARDBUS
RICOH
RC5C475II
Bus #1 Dev # 12
CardBus/16bitCard
i.LINK
PC Card
Connector
1 Slot
H8S/2149
KBC/EC
SPIC
H8S/2149
KBC/EC
SPIC
VCH
VCH
LCDCONN
SONY
12 XGA
LCD &
INVERTER
Cable
ROW#0,1
ROW#2,3
CLKGEN
IMI
C9835
Ether
PHY
Ether
PHY
KeyBoard
Membrane
RJ11
JOG
Contro ller
JOG
Controller
Cable( Primary IDE)
On Board
Memory
VGA DB-15
Printerx1
Serialx1
FDD x1
USB1
CD-ROM/
RW/DVD
USB(A) CONN x1
LPC
Audio
AD1881A
Audio
AD1881A
Memory
Stick
Module
Memory
Stick
Module
RJ45
LAN-A1
DC-IN
CONN
i.LINK0
i.LINK0
LAN-A0
LAN
LAN-A1
LAN
AC LINK
RJ11
AMP
Headphone
MIC
Speaker
Speaker
L&R
FWH
(Flash BIOS ROM)
FWH
(Flash BIOS ROM)
DCin
DCin
i.LINK1
i.LINK1
Super I/O
SMsC
LPC47N227
Super I/O
SMsC
LPC47N227
I/O Expander
& SM BUS MUX
I/O Expander
& SM BUS MUX
FAN
BATTERY
LID ATF
USB1
USB0
USB2
Seri al
Paral lele
Serial
Parallele
Refer to Clock Generator
Block Diagram
SMBUS
USB
CONN
FDD
FDD
i.LINK
SWX-72
Board
TouchPad
JOG
USB1
USB3
USB3
Display
Cash
Display
Cash
EEPROM
EEPROM
For Password
EEPROM
EEPROM
For LAN
SMB2
EEPROM
EEPROM
For i.LINK
MDC
(Modem Daughter
Card)
Module
MDC
(Modem Daughter
Card)
Module
is can not connect on main unit
when connected docking stataion
CPU Local Bus

PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
4-1 4-2
(END)
CHAPTER 4.
FRAME HARNESS DIAGRAM
81
18
12
FROM board connector (direct connection)
Harness (connector at both end)
Harness (soldered at one end)
1AY
CN4004
USB
CN4002
MIC/LINE
INPUT
CN4003
HEAD POHNE
KEY BOARD
24 1
CN1902
LITHIUM ION
BATTERY PACK
81
CN2702
Rear
NICKELHYDROGEN
BATTERY CN2802 2
1
HDD
PCG-R505TSK/R505TS: 20GB
PCG-R505TEK/R505TE: 15GB
49
1
50
2
CN2201
CNX-119 BOARD
SIDE B
1
20
CN4001
CN1301
i.LINK
PC
CARD
CONNECTOR
PC
CARD
MODEM
CARD
30 29
1
2
J1
30 29
1
2
34
168
35
CN1602
CON2 CN5002
CN5001
MODULAR
JACK
SPEAKER
L ch
CN1711
1
2
1
2
DC FAN
(WITH HEATSINK)
M
CN102
CNX-121 BOARD
SIDE B
CN4302
USB
CN702
EXT. DISPLAY
1
3
CN2801
CN4401
DC IN
CNX-131 BOARD
SIDE A
13
CN4402
1
20
CN1710
10 1
CN4301
112
CN3051
110
CN2003
1
12
CN4501
110
CN4701
112
CN4702
S4703
S4701 S4702 S4704
ENCODER
(ROTALY)
SWX-72 BOARD
SIDE A
EXTENSION
MEMORY MODULE
PCGA-MM64N/MM128N
12
59 60
61 62
143 144
CN502
131
CN701
299
1 100
CN1401
LCD
LEX-29 BOARD
SIDE A
CN4901
INVERTER UNIT
2
8
1
7
CN2004
8
1
CN4801 CN4802
2
1SPEAKER
R ch
POWER
SWX-76 BOARD
SIDE B
IFX-141 BOARD
SIDE A
MBX-48 BOARD
SIDE A
Side L
DOCKING STATION
PCGA-DSD5/DSM5
CN1502
HARNESS (LCD)
HARNESS (POWER 3P)
10
1
CN3071
FCC (10P)
FCC (12P)
10
1
CN4502
MEMORY
STICK
TOUCH PAD
CENTER
BUTTON
LEFT
BUTTON RIGHT BUTTON
FCC (10P)
FLEXIBLE FLAT CABLE (12 CORE)
FPC (HDD)
CN1202
FCC (8P) S4801
RJ-45 HARNESS (FOR INTERNAL)
HARNESS (2 PIN)
CNX-120 BOARD
SIDE B
NETWORK
Side R
FLEXIBLE FLAT CABLE (NI SHIELD) 20P

PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential
26 4-652-913-01 COVER (BP)
27 1-476-671-21 KEY BOARD UNIT (US)
28 1-763-688-11 FAN, DC (WITH HEATSINK)
29 1-815-304-11 CONNECTOR, PC CARD 1 SLOT
30 4-654-327-01 SHEET (GMCH), THERMAL
31 4-653-411-01 SHEET(PC CARD), INSULATING
* 32 4-652-932-01 HEATSINK (CPU)
* 33 4-652-924-01 BRACKET (VGA)
34 A-8049-520-A (R505TSK/R505TS)...
MBX-48 (850SS-H) (S)
34 A-8049-521-A (R505TEK/R505TE)...
MBX-48 (750SS-H) (S)
* 35 4-652-925-01 BRACKET (CPU)
36 1-960-827-31 HARNESS (2 PIN)
37 1-761-380-22 CARD, MODEM
38 4-653-412-01 SHEET (BOTTOM), INSULATING
39 1-961-140-11 HARNESS, RJ-45 (FOR INTERNAL)
40 X-4623-577-1 LID (DOC) ASSY
41 4-651-941-02 COVER (BBL)
42 A-8066-651-A COMPLETE PWB CNX-120
43 4-652-942-02 COVER (BBR)
44 1-790-750-13 FPC (HDD)
* 45 4-652-927-01 BRACKET (HDD R)
46 1-772-996-11 (R505TSK/R505TS)...
HDD (20.0GB-DK23BA-20)
46 1-796-070-11 (R505TEK/R505TE)...
HDD (15.0GB)-DK23BA
* 47 4-652-926-01 BRACKET (HDD F)
48 X-4623-575-2 HOUSING (BOTTOM) ASSY
49 A-8066-648-A COMPLETE PWB CNX-119
50 1-757-786-11 FLEXIBLE FLAT CABLE (NI SHIELD) 20P
51 4-641-449-01 FOOT (F)
52 X-4623-576-2 COVER (BOTTOM R) ASSY
53 4-652-918-01 LID (ETHER)
54 X-4623-578-1 LID (VGA) ASSY
55 4-654-610-02 COVER AIR DUCT
56 1-756-038-11 BATTERY, NICKEL HYDROGEN
57 1-961-147-11 HARNESS (POWER 3P)
58 A-8066-647-A COMPLETE PWB IFX-141
59 1-757-784-11 FFC (12P)
60 4-641-779-01 SPRING (BT), COMPRESSION COIL
61 1-757-792-11 FFC (10P)
62 A-8066-649-A COMPLETE PWB CNX-121
63 A-8066-650-A COMPLETE PWB CNX-131
64 4-653-432-01 CLAMP
65 4-654-326-01 SHEET (CPU), THERMAL
66 4-654-384-01 GND GASKET 5X15X1
67 4-654-450-02 SHEET (COVER LR)
68 4-654-382-01 CUSHION HDD CONNECTOR
69 4-654-518-01 SHIELD CNX 1
70 4-653-506-02 SHEET (MODEM)
71 4-654-517-01 SHIELD MBX 1
72 4-654-239-01 INSULATING SHEET
73 4-652-943-01 FOOT (R)
74 8-759-695-59 (R505TEK/R505TE)...
IC MT4LSDT864HG-10EB1
75 1-695-514-21 JACK (SMALL TYPE) 1P (HEAD PHONE)
76 1-793-100-11 CONNECTOR, USB
77 1-779-745-31 JACK, DC
B1 4-644-492-31 ACE (M2), LOCK (2X4)
B2 3-930-461-01 SCREW (DIA. 1.4X3.5), PRECISION
B3 4-644-492-01 ACE (M2), LOCK (2X6)
B5 4-648-320-01 TAPPING (M2) (2X4)
* B6 4-635-966-01 SCREW (HEX)
B7 4-645-016-31 ACE (M2) (DIA. 4.6), LOCK (2X2.5)
B8 7-621-255-15 SCREW +P 2X3
B9 4-651-989-11 SPACER (MBX)
B10 4-635-301-01 SCREW M3X4
B11 4-654-273-01 ACE (M2), LOCK (2X5)
B12 4-644-492-51 ACE (M2), LOCK
5-1 5-2
CHAPTER 5.
EXPLODED VIEWS AND PARTS LIST
NOTE:
•The mechanical parts with no reference number in the
exploded views are not supplied.
•Items marked “*”are not stocked since they are seldom
required for routine service. Some delay should be
anticipated when ordering these items.
•When the same reference numbers are written down in the
list, please use the one listed in the first place as the main
part.
5-1. Main Section
Ref.No. Part No. Description
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
*
To paste the thermal sheet (CPU) (65) to the heatsink
(CPU), warm the thermal sheet (CPU) adequately until it
becomes soft.
For further information, refer to the removal (page 1-9).
H
AB
C
A
D
E
E
G
L
I
N
O
Q
K
J
I
GJB
K
L
H
M
D
P
Q
M
O
F
C
N
F
1
B1
B1
B1
B1
B3
B11
B11
B5
B1
B1
B2 2
3
4
5
7
8
9
10
11
12
67
13
14 68
15
16
17 24
26
23
22
21
20
19
17
52
53
50
51 B1
B3
B3 B3
B1
B10
B10
B1
B1
B1
B12
B7
B6
B1
B1
B1
B12
B12
B1
B9
B7 B7
49
76
75 48 47 46
45
44
43
73
39
40
41
60
59
54
55
56
58
57
61 62
76
77
63
33
71
34
65 32
64
30
66
31
28
29
B1
36
37
B8
B3
B3
35
74
38
72
18
20
25
26
27
6
P
B11
42
70
69
R
B12
R
Ref.No. Part No. Description
1 A-8066-644-A COMPLETE PWB SWX-72
2 1-757-785-11 FFC (10P)
3 1-476-060-31 ENCODER (ROTALY)
4 4-652-922-02 BRACKET (JOG)
5 4-652-940-02 DETECTOR, LATCH
6 4-652-921-02 BUTTON (TP-R)
7 4-652-920-02 BUTTON (TP-L)
8 4-652-935-02 LENS (PALM REST)
9 4-652-907-01 HOUSING (PALM REST)
10 4-652-944-01 COVER, LENS
11 4-652-909-02 COVER (BOTTOM LF)
12 4-652-910-O2 COVER (BOTTOM LR)
13 4-652-923-02 ESCUTCHEON (TP)
14 4-653-410-01 SHEET (TP), INSULATING
15 1-772-529-61 PAD, TOUCH
16 1-790-729-11 CABLE, FLEXIBLE FLAT (12 CORE)
17 4-653-370-01 BRACKET, SPEAKER
18 1-757-787-11 FFC (8P)
19 1-544-847-11 SPEAKER (16MM, WITH HARNESS) R
20 4-653-371-01 CUSHION, SPEAKER
21 A-8066-645-A COMPLETE PWB SWX-76
22 4-653-372-01 CUSHION BUTTON PW
23 4-652-919-01 BUTTON (POWER)
24 1-544-846-11 SPEAKER (16MM, WITH HARNESS) L
25 X-4623-665-2 HOUSING (FRAME) ASSY

PCG-R505TE/R505TEK/R505TS/R505TSK (UC)
Confidential 5-3 5-4
5-2. LCD Section
Ref.No. Part No. Description
C
C
B
A
B
A
111
B4
B4
B13
B13
B4 B13
112
113
114
110
109
107
106
105
102
101
117
119
116
104 103
B13
B4
104
103
108
115
118
101 X-4623-574-2 HOUSING (BEZEL) ASSY
102 4-652-902-01 COVER (DL)
103 4-652-933-01 BLIND (SIDE), HOLE
104 4-652-934-01 BLIND (LCD), HOLE
105 4-652-938-01 CUSHION (LATCH)
106 4-652-904-02 LATCH
107 4-639-623-11 SPRING (LATCH), COIL
* 108 4-652-898-01 BRACKET (LCD-L)
109 A-8048-165-A LCD UNIT (12.1 TFTXGA) (S)
110 4-652-900-01 TILT UNIT (L)
111 X-4623-573-1 HOUSING (DISPLAY) ASSY
112 4-652-901-01 TILT UNIT (R)
113 1-476-317-12 INVERTER UNIT
114 A-8066-646-A COMPLETE PWB LEX-29
* 115 4-652-899-01 BRACKET (LCD-R)
116 1-961-063-11 HARNESS (LCD)
117 4-652-903-01 COVER (DR)
118 4-654-412-01 SPACER (LCD)
119 4-654-007-01 (R505TSK)...LABEL (ID (U))
119 4-654-007-11 (R505TS)...LABEL (ID (U))
119 4-654-007-21 (R505TEK)...LABEL (ID (U))
119 4-654-007-31 (R505TE)...LABEL (ID (U))
B4 4-643-356-01 SCREW (M2X5)
B13 4-644-492-21 ACE (M2), LOOCK (2X3)