Sony LMD-2735MD User manual

4-584-947-11(1)
LCD Monitor
Instructions for Use
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
LMD-2735MD
LMD-2435MD
© 2016 Sony Corporation
2016-03

2
Indications for Use/Intended Use
The Sony LMD-2735MD/2435MD LCD Monitor are
intended to provide 2D color video displays of images
from surgical endoscopic/laparoscopic camera systems
and other compatible medical imaging systems.
The LMD-2735MD/2435MD monitor are a widescreen,
high-definition, medical grade monitor for real-time use
during minimally invasive surgical procedures and are
suitable for use in hospital operating rooms, surgical
centers, clinics, doctors’ offices and similar medical
environments.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
No modification of this equipment is allowed.
WARNING
To avoid the risk of electric shock, this equipment
must only be connected to a supply mains with
protective earth.
Warning
This unit has no power switch.
To disconnect the main power, unplug the power plug.
When installing the unit, incorporate a readily accessible
disconnect device in the fixed wiring, or connect the
power plug to an easily accessible socket-outlet near the
unit.
Do not position the ME equipment where it is difficult
to unplug the power plug.
If a fault should occur during operation of the unit,
operate the disconnect device to switch the power supply
off, or unplug the power plug.
For the customers in the U.S.A.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of part 15 of FCC Rules.
Symbols on the products
Safety sign
Follow the warnings in the instructions for
use for parts of the unit on which this mark
appears.
NOTE Background color: Blue
Symbol: White
Consult the Instructions for Use
Follow the directions in the Instructions for
Use for parts of the unit on which this mark
appears.
This symbol indicates the manufacturer,
and appears next to the manufacturer’s
name and address.
This symbol indicates the European
Community representative, and appears
next to the European Community
representative’s name and address.
This symbol indicates the serial number.
This symbol indicates the version of the
accompanying document.
This symbol indicates the date of
manufacture.
This symbol indicates the equipotential
terminal which brings the various parts of a
system to the same potential.
Storage and transport temperature
This symbol indicates the acceptable
temperature range for storage and transport
environments.
Storage and transport humidity
This symbol indicates the acceptable
humidity range for storage and transport
environments.
Storage and transport pressure
This symbol indicates the acceptable
atmospheric pressure range for storage and
transport environments.

3
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
For the customers in Canada
CAN ICES-3 (A)/NMB-3(A)
This unit has been certified according to Standard CAN/
CSA-C22.2 No.60601-1.
Important safeguards/notices for use in the
medical environments
1. All the equipments connected to this unit shall be
certified according to Standard IEC 60601-1, IEC
60950-1, IEC 60065 or other IEC/ISO Standards
applicable to the equipments.
2. Furthermore all configurations shall comply with the
system standard IEC 60601-1. Everybody who
connects additional equipment to the signal input
part or signal output part configures a medical
system, and is therefore, responsible that the system
complies with the requirements of the system
standard IEC 60601-1.
If in doubt, consult the qualified service personnel.
3. The leakage current could increase when connected
to other equipment.
4. For this particular equipment, all accessory
equipment connected as noted above, must be
connected to mains via an additional isolation
transformer conforming with the construction
requirements of IEC 60601-1 and providing at least
Basic Insulation.
5. This equipment generates, uses, and can radiate
radio frequency energy. If it is not installed and used
in accordance with the instruction manual, it may
cause interference to other equipment. If this unit
causes interference (which can be determined by
unplugging the power cord from the unit), try these
measures: Relocate the unit with respect to the
susceptible equipment. Plug this unit and the
susceptible equipment into different branch circuit.
Consult your dealer. (According to standard IEC 60601-
1-2 and CISPR11, Class B, Group 1)
Important EMC notices for use in the medical environments
The LMD-2735MD/2435MD needs special precautions regarding EMC and needs to be installed and put into service
according to the EMC information provided in the instructions for use.
The portable and mobile RF communications equipment such as cellular phones can affect the LMD-2735MD/
2435MD.
Warning
The use of accessories and cables other than those specified, with the exception of replacement parts sold by Sony
Corporation, may result in increased emissions or decreased immunity of the LMD-2735MD/2435MD.
Warning
If the LMD-2735MD/2435MD should be used adjacent to or stacked with other equipment, it should be observed to
verify normal operation in the configuration in which it will be used.
Guidance and manufacturer’s declaration-electromagnetic emissions
The LMD-2735MD/2435MD is intended for use in the electromagnetic environment specified below.
The customer or the user of the LMD-2735MD/2435MD should assure that it is used in such an environment.
Emission test Compliance Electromagnetic environment-guidance
RF emissions
CISPR 11 Group 1
The LMD-2735MD/2435MD uses RF energy only for its
internal function. Therefore, its RF emissions are very low and
are not likely to cause any interference in nearby electronic
equipment.
RF emissions
CISPR 11
Class B
The LMD-2735MD/2435MD is suitable for use in all
establishments, including domestic establishments and those
directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class D (AC input)
Not applicable (DC input)
Voltage f luc tuat ions/
flicker emissions
IEC 61000-3-3
Complies (AC input)
Not applicable (DC input)

4
Guidance and manufacturer’s declaration - electromagnetic immunity
The LMD-2735MD/2435MD is intended for use in the electromagnetic environment specified below. The customer or the user of the
LMD-2735MD/2435MD should assure that it is used in such as environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment-guidance
AC input DC input
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30%.
Electrical fast
transient/burst
IEC 61000-4-4
±2 kV for power
supply lines
±1 kV for input/
output lines
±2 kV for power
supply lines
±1 kV for input/
output lines
±1 kV for input/
output lines
Mains power quality should be that of a
typical commercial or hospital
environment.
Surge
IEC 61000-4-5
±1 kV line(s) to
line(s)
±2 kV line(s) to
earth
±1 kV differential
mode
±2 kV common
mode
Not applicable Mains power quality should be that of a
typical commercial or hospital
environment.
Voltage dips, short
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
< 5%
(> 95% dip in )
for 0.5 cycle
40%
(60% dip in )
for 5 cycles
70%
(30% dip in )
for 25 cycles
< 5%
(> 95% dip in )
for 5 sec
< 5%
(> 95% dip in )
for 0.5 cycle
40%
(60% dip in )
for 5 cycles
70%
(30% dip in )
for 25 cycles
< 5%
(> 95% dip in )
for 5 sec
Not applicable Mains power quality should be that of a
typical commercial or hospital
environment. If the user of the LMD-
2735MD/2435MD requires continued
operation during power mains
interruptions, it is recommended that the
LMD-2735MD/2435MD be powered
from an uninterruptible power supply or a
battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m 3 A/m 3 A/m Power frequency magnetic fields should
be at levels characteristic of a typical
location in a typical commercial or
hospital environment.
NOTE: is the a.c. mains voltage prior to application of the test level.

5
Guidance and manufacturer’s declaration - electromagnetic immunity
The LMD-2735MD/2435MD is intended for use in the electromagnetic environment specified below. The customer or the user of the
LMD-2735MD/2435MD should assure that it is used in such as environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic environment-guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to 80 MHz
3 V/m
80 MHz to 2.5 GHz
3 Vrms
3 V/m
Portable and mobile RF communications equipment should be
used no closer to any part of the LMD-2735MD/2435MD,
including cables, than the recommended separation distance
calculated from the equation appliance to the frequency of the
transmitter.
Recommended separation distance
d= 1.2
d= 1.2 80 MHz to 800 MHz
d= 2.3 800 MHz to 2.5 GHz
Where Pis the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and dis
the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey, ashould be less than the compliance
level in each frequency range. b
Interference may occur in the vicinity of equipment marked with
following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
location in which the LMD-2735MD/2435MD is used exceeds the applicable RF compliance level above, the LMD-2735MD/2435MD
should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as
reorienting or relocating the LMD-2735MD/2435MD.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

6
Caution
When you dispose of the unit or accessories, you must
obey the laws in the relative area or country and the
regulations in the relative hospital regarding
environmental pollution.
Warning on power connection
Use a proper power cord for your local power supply.
1. Use the approved Power Cord (3-core mains lead) /
Appliance Connector / Plug with earthing-contacts
that conforms to the safety regulations of each
country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance
Connector / Plug conforming to the proper ratings
(Voltage, Ampere).
If you have questions on the use of the above Power
Cord / Appliance Connector / Plug, please consult a
qualified service personnel.
For the customers in U.S.A. and Canada
Warning on power connection for medical use
Please use the following power supply cord. With
connectors (plug or female) and cord types other than
those indicated in this table, use the power supply cord
that is approved for use in your area.
*Note: Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked 'Hospital Only' or 'Hospital
Grade'.
Caution
When installing, the installation space must be secured
in consideration of the ventilation and service operation.
Leave a space 10 cm (4 inches) or more behind, 10 cm (4
inches) or more from the left and right sides of, 8 cm
(3 1/4inches) or more from the bottom side of, and
30 cm (11 7/8inches) or more above the unit.
Warning
The apparatus shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases,
shall be placed on the apparatus.
Warning
To prevent injury, this apparatus must be securely
attached to the mounting arm/wall in accordance with
the instructions for use.
Recommended separation distances between portable and mobile RF communications equipment and the LMD-2735MD/
2435MD
The LMD-2735MD/2435MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The customer or the user of the LMD-2735MD/2435MD can help prevent electromagnetic interference by maintaining a minimum
distance between portable and mobile RF communications equipment (transmitters) and the LMD-2735MD/2435MD as recommended
below, according to the maximum output power of the communications equipment.
Rated maximum output power of transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d= 1.2
80 MHz to 800 MHz
d= 1.2
800 MHz to 2.5 GHz
d= 2.3
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated a maximum output power not listed above, the recommended separation distance din meters (m) can be
estimated using the equation applicable to the frequency of the transmitter, where Pis the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects and people.
United States and Canada
Plug Type HOSPITAL GRADE*
Cord Type Min. Type SJT
Min. 18 AWG
Minimum Rating for Plug and
Appliance Couplers
10A/125V
Safety Approval UL Listed and CSA
For the customers in the U.S.A.
Caution
Federal law (United States of America)
restricts this device to sale by or on the order of
a licensed healthcare practitioner.

7
Consult with Sony qualified personnel for mounting
arm/wall mount installation.
For the customers in the U.S.A.
SONY LIMITED WARRANTY - Please visit http://
www.sony.com/psa/warranty for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
For the customers in Canada
SONY LIMITED WARRANTY - Please visit http://
www.sonybiz.ca/pro/lang/en/ca/article/resources-
warranty-product-registration for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
For the customers in Europe
Sony Professional Solutions Europe - Standard
Warranty and Exceptions on Standard Warranty.
Please visit http://www.pro.sony.eu/warranty for
important information and complete terms and
conditions.
For the customers in Korea
SONY LIMITED WARRANTY - Please visit http://
bpeng.sony.co.kr/handler/BPAS-Start for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.

Table of Contents
8
Table of Contents
Precaution .......................................................9
On Safety .................................................................. 9
On Installation ......................................................... 9
Precautions for using this unit safely .................... 9
Precautions for connecting this unit with other
medical devices ..................................................... 9
On simultaneous use with an electrosurgical
knife, etc. ................................................................ 9
Recommendation to Use more than One Unit ... 9
About the LCD Display Panel ............................... 9
On a Long Period of Use ...................................... 10
On Burn-in ............................................................ 10
On Temperature Error .......................................... 10
On Moisture Condensation ................................. 10
On Cleaning ........................................................... 10
On Repacking ........................................................ 11
Disposal of the Unit .............................................. 11
Features .........................................................11
Location and Function of Parts and
Controls ........................................................12
Front Panel............................................................. 12
Input Signals and Adjustable/Setting Items....... 13
Rear/Bottom Panel................................................ 14
Connecting the Power Cord .........................15
Initial Setting ................................................16
Using the Menu ............................................. 18
Adjustment Using the Menus ....................... 19
Items ........................................................................ 19
Adjusting and changing the settings ................... 20
Color Tone Adjustment menu ...................... 20
Screen Control menu ...................................... 21
PIP / POP menu .............................................. 21
Input Configuration menu ............................ 22
System Configuration menu .......................... 23
Initial Setup menu ........................................... 24
Preset menu ...................................................... 25
Troubleshooting ...........................................25
Error Messages ..............................................26
Specifications ................................................26
Dimensions ...................................................31
LMD-2735MD ....................................................... 31
LMD-2435MD ....................................................... 31

Precaution 9
Precaution
On Safety
Operate the unit only with a power source as specified
in the “Specifications” section.
The nameplate indicating operating voltage, etc. is
located on the rear panel of monitor and the AC
adaptor.
Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
Unplug the unit from the wall outlet if it is not to be
used for several days or more.
To disconnect the AC power cord, pull it out by
grasping the plug. Never pull the cord itself.
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
On Installation
Prevent internal heat build-up allowing adequate air
circulation.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
Do not install the unit near heat sources such as
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or
shock.
Do not place the monitor near equipment which
generates magnetism, such as a transformer or high
voltage power lines.
Precautions for using this unit safely
Some people may experience discomfort (such as eye
strain, fatigue, or nausea) while watching video
images. Sony recommends that all viewers take regular
breaks while watching video images. The length and
frequency of necessary breaks will vary from person to
person. You must decide what works best. If you
experience any discomfort, you should stop watching
the video images until the discomfort ends; consult a
doctor if you believe necessary.
Avoid watching the display in environments where
your head may shake, or while you are walking or
performing exercise, because there is a higher
possibility that you experience discomfort.
Precautions for connecting this unit
with other medical devices
Before you utilize this device and/or connect this
device to any other medical device, please be aware of
and abide by the following precautions:
(a) Before actually using this device for medical
practice, please check and confirm that you do not
experience any discomfort in your use that could be
disruptive or impeditive in conducting your intended
activity or medical practice.
(b) If you experience or are likely to experience such
discomfort, please refrain from using this device.
(c) Generally, discomfort (such as eye strain, fatigue,
nausea, or motion sickness) can be provoked by such
factors as quick movements or shakiness of video
picture, focal position of video pictures, distance
between objects and image capturing modules, user’s
point of gaze in video pictures, other varying
conditions of video pictures to be input to this device,
and individual user’s health conditions.
Before you utilize this unit, check if the image of the
connected medical device is displayed properly on the
screen of this unit.
On simultaneous use with an
electrosurgical knife, etc.
If this unit is used together with an electrosurgical knife,
etc., the picture may be disturbed, warped or otherwise
abnormal as a result of strong radio waves or voltages
from the device. This is not a malfunction.
When you use this unit simultaneously with a device
from which strong radio waves or voltages are emitted,
confirm the effect of this before using such devices, and
install this unit in a way that minimizes the effect of
radio wave interference.
Recommendation to Use more than
One Unit
As problems can occasionally occur for the monitor,
when the monitor is used for safety control of personnel,
assets or stable picture, or for emergencies, we strongly
recommend you use more than one unit or prepare a
spare unit.
About the LCD Display Panel
The LCD panel fitted to this unit is manufactured with
high precision technology, giving a functioning pixel
ratio of at least 99.99%. Thus a very small proportion

Precaution
10
of pixels may be “stuck”, either always off (black),
always on (red, green, or blue), or flashing. In addition,
over a long period of use, because of the physical
characteristics of the liquid crystal display, such
“stuck” pixels may appear spontaneously. These
problems are not a malfunction.
Do not leave the LCD screen facing the sun as it can
damage the LCD screen. Take care when you place the
unit by a window.
Do not push or scratch the LCD screen. Do not place
a heavy object on the LCD screen. This may cause the
screen to lose uniformity.
If the unit is used in a cold place, a residual image may
appear on the screen. This is not a malfunction. When
the monitor becomes warm, the screen returns to
normal.
The screen and the cabinet become warm during
operation. This is not a malfunction.
On a Long Period of Use
Due to the characteristics of LCD panel, displaying static
images for extended periods, or using the unit repeatedly
in a high temperature/high humidity environments may
cause image smearing, burn-in, areas of which
brightness is permanently changed, lines, or a decrease
in overall brightness.
In particular, continued display of an image smaller than
the monitor screen, such as in a different aspect ratio,
may shorten the life of the unit.
Avoid displaying a still image for an extended period, or
using the unit repeatedly in a high temperature/high
humidity environment such an airtight room, or around
the outlet of an air conditioner.
To prevent any of the above issues, we recommend
reducing brightness slightly, and to turn off the power
whenever the unit is not in use.
On Burn-in
For LCD panel, permanent burn-in may occur if still
images are displayed in the same position on the screen
continuously, or repeatedly over extended periods.
Images that may cause burn-in
Masked images with aspect ratios other than 16:9
Color bars or images that remain static for a long time
Character or message displays that indicate settings or
the operating state
To reduce the risk of burn-in
Turn off the character displays
Press the MENU button to turn off the character
displays. To turn off the character displays of the
connected equipment, operate the connected
equipment accordingly. For details, refer to the
operation manual of the connected equipment.
Turn off the power when not in use
Turn off the power if the monitor is not to be used for
a prolonged period of time.
On Temperature Error
When this unit is used in a high temperature
environment and the internal temperature rises, a
temperature error is displayed on the screen. When the
temperature error is displayed, contact an authorized
Sony dealer.
On Moisture Condensation
If the unit is suddenly taken from a cold to a warm
location, or if ambient temperature suddenly rises,
moisture may form on the outer surface of the unit and/
or inside of the unit. This is known as condensation. If
condensation occurs, turn off the unit and wait until the
condensation clears before operating the unit. Operating
the unit while condensation is present may damage the
unit.
On Cleaning
Before cleaning
Be sure to disconnect the AC power cord from the AC
outlet.
On cleaning the monitor
A material that withstands disinfection is used for the
front protection plate of the medical use LCD monitor.
The protection plate surface is specially treated to reduce
reflection of light. When solvents such as benzene or
thinner, or acid, alkaline or abrasive detergent, or
chemical cleaning cloth are used for the protection plate
surface/monitor surface, the performance of the
monitor may be impaired or the finish of the surface may
be damaged. Take care with respect to the following:
Clean the protection plate surface/monitor surface
with a 50 to 70 v/v% concentration of isopropyl
alcohol or a 76.9 to 81.4 v/v% concentration of ethanol
using a swab method. Wipe the protection plate
surface gently (wipe using less than 1 N force).
Stubborn stains may be removed with a soft cloth such
as a cleaning cloth lightly dampened with mild
detergent solution using a swab method and then
clean using the above chemical solution.

Features 11
Never use solvents such as benzene or thinner, or acid,
alkaline or abrasive detergent, or chemical cleaning
cloth for cleaning or disinfection, as they will damage
the protection plate surface/monitor surface.
Do not use unnecessary force to rub the protection
plate surface/monitor surface with a stained cloth. The
protection plate surface/monitor surface may be
scratched.
Do not keep the protection plate surface/monitor
surface in contact with a rubber or vinyl resin product
for a long period of time. The finish of the surface may
deteriorate or the coating may come off.
On Repacking
Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit.
If you have any questions about this unit, contact your
authorized Sony dealer.
Disposal of the Unit
Do not dispose of the unit with general waste.
Do not include the monitor with household waste.
Features
Compliance with medical safety standards
in U.S.A., Canada and Europe
IEC 60601-1 and product safety standards in the U.S.A.,
Canada and Europe have been obtained for this monitor.
The monitor is designed for use in the medical treatment
field, with the sheet switch, screen protect panel, etc.
High-resolution Full HD panel
A Full HD high-resolution (1920 × 1080) panel and wide
field of view technology enables you to use the monitor
under various lighting conditions and in numerous ways
(installing on the ceiling, wall, using several monitors to
view an image, etc.).
Control panel
Assigns functions frequently used during an operation
to buttons on the front surface of the monitor. The panel
provides an user interface superior in operability
through navigation by luminescent colors and status of
the buttons.
About this manual
The instructions in this manual are for the following
models:
LMD-2735MD
LMD-2435MD
The illustration of LMD-2735MD is used for the
explanations. Any differences in specifications are
clearly indicated in the text.

Location and Function of Parts and Controls
12
Location and Function of Parts and Controls
Front Panel
Power indicator
When the power is turned on, the power indicator lights
in green.
When the protection function is activated and the
display brightness is reduced due to the rise in
temperature, it flashes in green.
When the unit switches to the standby state, it lights in
orange.
CONTROL button
Displays or clears the operating buttons on the front
panel.
Selects the items depending on the menu types.
OSD menu operation buttons
MENU button
Press to display the on-screen menu.
Press again to clear the menu.
///buttons
Press to select the items and setting values.
CUSTOM button
Turns on or off the assigned function. You can adjust the
assigned function by pressing the /buttons. (Refer to
the custom buttons of the system configuration menu on
page 24 and of the default setting on page 25.)
The following functions are assigned in the default
setting.
CUSTOM 1: Brightness
CUSTOM 2: Contrast
CUSTOM 3: Flip
Multi-image display setting buttons
PIP/POP: For displaying the multi-image display
or switching the multi-image display mode.
SWAP: For swapping between the main display
and the sub display.
Note
If the combination of input assigned to each port is set
to VIDEO and S VIDEO, the multi-image display is
not displayed.
Input select buttons

Location and Function of Parts and Controls 13
PORT A: Displays the input signal assigned to
PORT A. When the input signal of PORT A is
displayed, a menu which allows you to select the input
signal to be assigned to PORT A is displayed.
PORT B: Displays the input signal assigned to
PORT B. When the input signal of PORT B is
displayed, a menu which allows you to select the input
signal to be assigned to PORT B is displayed.
(ON/STANDBY) switch
Press the side to turn the monitor on. Press the side
to switch the unit to standby state.
When the unit switches to the standby state, the power
indicator lights in orange.
About the Status of the Power Indicator
Input Signals and Adjustable/Setting Items
: Can be adjusted/set
×: Cannot be adjusted/set
1) Reflected on the screen only when the SD signal is input.
2) Reflected on the screen only when the HD signal is input.
3) The setting value can be changed but is not applied to the screen when
the PC signal is input.
4) Select RGB when the PC signal is input.
5) The setting value can be changed but is not applied to the screen when
the B&W signal is input.
Status Operating State
Orange Standby
Flashes in Orange No image displayed (remote standby)
Green Power on
Flashes in Green Power on with image displayed
(reduced backlight due to high
temperature)
Input signal
Item
VIDEO/S-VIDEO
(See page 28.) HD15 DVI-D
SDI
(See page
28.)
Video,
Y/C B & W
Video
(See page 28.) PC
(See page
29.)
RGB video
(See page
28.)
PC
(See page
29.)
Component RGB
Contrast 
Brightness 
Chroma ×5) 
Phase ×5) 
Color Temperature 
ACC ×5) ××××××
CTI ×5) ××××××
Sharpness V 
Sharpness H 
NTSC Setup 
(NTSC)

(480/60I)
××××××
SD Scan Size 1) 1) ×3) 1) ×3) 1)
HD Scan Size ××2) 2) ×3) 2) ×3) 2)
Gamma 
SD Aspect 1) 1) ×3) 1) ×3) 1)
Mono ×5) 
APA ×××××××
Shift H/Shift V ×××××××
Dot Pitch ×××××××
Dot Phase ×××××××
Sync Detect ×××3) ×××
RGB Range ××××××
Flip Pattern 
RGB/YPbPr ××4) ×××

Location and Function of Parts and Controls
14
Rear/Bottom Panel
(Equipotential) terminal
Connects the equipotential plug.
Slide the shutter and select an input terminal that
you want to use.
(AC input) connector
Connects the supplied AC power cord.
Sony AC-120MD (DC input) connector
Connect the DC connector of the separately sold AC
adaptor.
Connect the DC connector to the unit, then connect the
power cord of the AC adaptor.
To remove the DC connector, remove the power cord of
the AC adaptor, then remove the DC connector.
For the DC power supply, make sure to use the separately
sold AC adaptor, AC-120MD. If another power supply is
used, there is a risk of fire or electric shock.
5V 2.0A (DC output) connector
Outputs 5 volts for connected external equipment.
SERIAL REMOTE connector (RJ-45)
The monitor can be operated according to control
commands sent from connected external equipment.
Connect to the network by using a 10BASE-T/100BASE-
TX LAN cable (non-shielded type of 5 or more category,
optional).
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
The connection speed may be affected by the network
system. This unit does not guarantee the
communication speed or quality of 10BASE-T/
100BASE-TX.
SERIAL REMOTE RS-232C connector (D-sub
9-pin, female)
The monitor can be operated according to control
commands sent from connected external equipment.
SDI input connector (BNC type)
Input connector for serial digital component signals.
HD15 input connector (D-sub 15-pin, female)
The Plug & Play function corresponds to DDC2B.
DVI-D input/output connector (DVI-D)
connector

Connecting the Power Cord 15
Input DVI Rev.1.0 applicable digital signal.
connector
Active through output connector of the DVI digital
signal.
Outputs the signal which inputs to the connector.
The signal protected by HDCP 1) is not output.
1) HDCP (High-bandwidth Digital Content Protection) is a
copyright protection technology using encryption
technology of digital video signals.
Note
A signal is output from the connector only when the
monitor is turned on. When the monitor is turned off,
the signal is not output from the connector.
VIDEO input connector (BNC type)
The input connector for composite signals.
S-VIDEO input connector (4-pin mini-DIN)
The input connector for Y/C signals.
Do not come into contact with the terminals of the rear
panel connectors and patients at the same time.
Doing so may result in a generation of voltage that can be
harmful to patients if the unit is malfunctioning.
Always disconnect the power cord before connecting
and disconnecting connectors.
Using this unit for medical purposes
This equipment’s connectors are not isolated.
Do not connect any device other than one which
conforms to IEC 60601-1.
When an information technology device or AV device
that uses an alternating current is connected, current
leakage may result in an electric shock to the patient or
operator.
If use of such a device is unavoidable, isolate its power
supply by connecting an isolation transformer, or by
connecting an isolator between the connecting cables.
After implementing these measures, confirm that the
reduced risk now conforms to IEC 60601-1.
Connecting the Power
Cord
To connect the power cord
1 Press the side of the switch and switch the
unit to the standby state.
2 Slide the shutter of the AC connector of the unit to
the right, then insert the AC power cord into the AC
input connector as illustrated.
To use the AC adaptor (sold separately)
Switch the unit to the standby state by pressing the
side of the switch, slide the shutter of the power
connector on the unit to the left, then insert the DC
connector into the DC input connector until it locks.
Next, insert the AC power cord into the separately sold
AC adaptor.
AC input connector
Shutter
AC power cord
AC plug holder
Shutter
DC input connector
DC connector

Initial Setting
16
To remove the power cord
Switch the unit to the standby state by pressing the
side of the switch, then remove the AC power cord.
When using the separately sold AC adaptor, switch the
unit to the standby state, remove the AC power cord
from the AC adaptor, then remove the DC connector
from the unit.
Initial Setting
When you turn on the unit for the first time after
purchasing it, select the area and language where you
intend to use this unit from among the options.
To set the using area
1 Turn on the unit .
The Area Setting screen appears.
2 Press the CONTROL button.
Color
Temperature NTSC Setup
North America D65 7.5%
Latin America - Argentina D65 0%
Latin America - Paraguay D65 0%
Latin America - Uruguay D65 0%
Latin America - Other D65 7.5%
Africa, Australasia
Europe, Middle-East
D65 0%
Asia Except Japan - NTSC D65 7.5%
Asia Except Japan - PAL D65 0%
Japan D93 0%






Initial Setting 17
3 Press the or button to select the area where you
intend to use the unit and press the button.
When the confirmation screen is displayed, press
the or button to select Yes and press the
CONTROL button.
If you select Asia Except Japan
Customers who will use this unit in the shaded
areas shown in the map below except for Japan
should select Asia Except Japan - NTSC.
Other customers should select Asia Except Japan -
PAL.
4 The Area Setting screen disappears and the menu
item settings suitable for the selected area are
applied.
Note
When you have selected the wrong area, set the
following items using the menu.
Color Temperature (on page 20)
NTSC Setup (on page 21)
See “To set the using area” (page 16) on the setting value.
To set the using language
You can select one of eight languages (English, Chinese,
Japanese, Italian, Spanish, German, French, and
Russian) for display on the menu and other on-screen
displays. The default menu language is set to “English.”
1 Turn on t he unit.
Select the area where you intend to use this unit on
the Area Setting screen. (See page 16.)
2 The Language Setting screen is displayed.
3 Press the or button to select the language and
press the button.
When the confirmation screen is displayed, press 
or button to select Yes and press the CONTROL
button.
To change the menu language
Select the area and language which you use. See this
section when you change the using language.
1 Press the MENU button.
The menu-selecting screen appears.
The menu presently selected is shown in blue.
2 Press the /button to select “System
Configuration.”
The “System Configuration” menu appears.
The selected tab is displayed in blue.
3 Press the /button to select the “OSD Setting”
tab.
The “OSD Setting” menu appears.

Using the Menu
18
4 Press the /button to select “Language.”
The selected item is displayed in blue.
5 Press the /button to select a language.
The menu changes to the selected language.
To clear the menu
Press the MENU button.
The menu disappears automatically if a button is not
pressed for one minute.
Using the Menu
The unit is equipped with an on-screen menu for
making various adjustments and settings such as picture
control, input setting, setting change, etc.
To change the menu language, refer to “To change the
menu language” on page 17.
1 Press the CONTROL button.
The operation buttons are displayed.
2 Press the MENU button.
The menu-selecting screen appears.
The menu presently selected is shown in blue.
3 Press the /button to select a menu.
When you press the or CONTROL button, the
selected menu appears and setting items of the
selected tab are displayed.
4 Press the /button to select the tab.

Adjustment Using the Menus 19
The selected tab is shown in blue, and setting items
of the selected tab appear.
5 Select an item.
Press the /button to select the item.
The item to be changed is displayed in blue.
6 Make the setting or adjustment on an item.
When changing the adjustment level:
To increase the number, press the button.
To decrease the number, press the button.
When selecting the setting:
Press the /button to select the setting.
If the Control Lock is set to “On,” the setting cannot
be changed.
For details about Control Lock, see page 23.
About the memory of the settings
The settings are automatically stored in the monitor
memory.
About the control navigation
Depending on the state, the operating buttons of the unit
light as shown below:
White light: Operable state.
Green light: Operating state.
Off: Unable to operate.
Adjustment Using the
Menus
Items
The screen menu of this monitor consists of the
following items.
Color Tone Adjustment
Gamma
Phase
Chroma
Brightness
Contrast
Color Temperature
Gain R Offset
Gain G Offset
Gain B Offset
Bias R Offset
Bias G Offset
Bias B Offset
Mono
Sharpness H
Sharpness V
RGB Range
RGB/YPbPr
Sync Detect
ACC
CTI
NTSC Setup
Screen Control
HD Scan Size
SD Scan Size
Flip Pattern
SD Aspect
APA
Shift H
Shift V
Dot Phase
Dot Pitch
PIP / POP
Clipping Size
Sub Screen Position
Pattern Skip
Input Configuration
Port A Input Select
Port B Input Select

Adjustment Using the Menus
20
Input Name
Power Supply
HDCP Setting
Auto Input Select
System Configuration
Control Lock
OSD Setting
Power On Setting
Power Save
Serial Remote
Ethernet Setting
Custom Button
Panel Display
Monitor Information
Initial Setup
Language
Port A Input Select
Port B Input Select
Pattern Skip
PIP / POP
Custom Button
Auto Input Select
Preset
Load User Setting
Save User Setting
User Name
Load Default
Adjusting and changing the settings
Color Tone Adjustment menu
The Color Tone Adjustment menu is used to adjust
picture quality for each input.
You need to use the measurement instrument to adjust
the color temperature.
Recommended: Konica Minolta color analyzer CA-310
Submenu Setting
Gamma Select the appropriate gamma mode
from among “1.8,” “2.0,” “2.2,” “2.4,”
“ 2 . 6 ,” “ D I C OM .”
“DICOM” is for reference, not
diagnostic, purposes only.
Phase Adjusts color tones. The higher the
setting, the more greenish the picture.
The lower the setting, the more purplish
the picture.
Chroma Adjusts color intensity. The higher the
setting, the greater the intensity. The
lower the setting, the lower the
intensity.
Brightness Adjusts brightness.
Contrast Adjusts contrast.
Color Temperature Select the color temperature from
among “D56,” “D65,” “D93.”
Note
If the setting is changed, Gain R/G/B
Offset and Bias R/G/B Offset are
restored to 0 respectively.
Gain R Offset
Gain G Offset
Gain B Offset
Adjust color temperature in detail, and
color balance (Gain).
Bias R Offset
Bias G Offset
Bias B Offset
Adjust color temperature in detail, and
color balance (Bias).
Mono Sets the display to a monochrome
picture. Set to “On” for a monochrome
picture, set to “Off” for a normal
(chromatic) picture.
Sharpness H Adjusts the horizontal sharpness. The
higher the setting, the sharper the
picture. The lower the setting, the softer
the picture.
Sharpness V Adjusts the vertical sharpness. The
higher the setting, the sharper the
picture. The lower the setting, the softer
the picture.
RGB Range Sets the RGB signal range. Select from
among “Auto,” “Limited,” “Full.” If you
set to “Auto,” this item is set to
“Limited” when inputting video signal,
and “Full” when inputting PC signals.
RGB/YPbPr Sets the input signal of the HD15
connector. Select from among “RGB,”
“YPbPr.”
Note
Select “RGB” to display PC signals.
Sync Detect Sets detection of the sync signal of the
input signal. Select from among “Auto,”
“Internal,” “External.” If you set to
“Auto,” external synchronization is
prioritized. If there is no external
synchronization, internal
synchronization is set.