Sony SDM-HS73P User manual

MENU
OK
COLOR MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
MODEL: SDM-HS73P ( U/C AEP CH Model )

1. LCD CHARACTERISTICS
Type : TFT Color LCD Module
Active Display Area : 17 inch(337.92(H) x 270.336(V))
Size : 358.5(W) x 296.5(H) x 19.5(D)
Pixel Pitch : 0.264 (Per one triad) x 0.264
Color Depth : 16.2M Colors
Electrical Interface : LVDS
Operating Mode : Normally White
Backlight Unit : 4-CCFL (Cold Cathode
Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥
10
Left : -60° min., -70°(Typ) Right : +60° min., +70°(Typ)
Top :+60° min., +70°(Typ) Bottom : -60°min., -70°(Typ)
2-2. Luminance : 350(min), 400(Typ)
2-3. Contrast Ratio : 250(min), 450(Typ)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• Type : Separate Sync
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.70 V( 5%)
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.35 Vp-p
c) Color 15, 0 : 0.7 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Horizontal : 28 ~ 80kHz
Vertical : 48 ~ 75Hz
4
. Max. Resolution
Analog : 1280 x 1024 / 75Hz
5. POWER SUPPLY
5-1. Power
: AC 100~240V, 50/60Hz , 1.0A
5-2. Power Consumption
6. ENVIRONMENT
6-1. Operating Temperature: 5°C~35°C (41°F~95°F)
(Ambient)
6-2. Relative Humidity : 10%~80%
(Non-condensing)
6-3. MTBF : 50,000 Hours(Typ)
30,000 Hours(Min)
7. DIMENSIONS (with TILT/SWIVEL)
Width : 441 mm (17.36'')
Depth : 216 mm (8.50'')
Height : 404 mm (15.90'')
8. WEIGHT (with TILT/SWIVEL)
Net. Weight : 6.0 kg (13.23 lbs)
Gross Weight : 8.1 kg (18.86 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ........................................................4
OPERATING INSTRUCTIONS ................................ 5
WIRING DIAGRAM ................................................. 6
BLOCK DIAGRAM ................................................... 7
ADJUSTMENT ...................................................... 8
EXPLODED VIEW.................................................. 9
ACCESSORIES & PACKING MATERIALS............ 10
MODE
POWER ON (NORMAL)
STAND-BY
SUSPEND
DPMS OFF
POWER S/W OFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF/OFF
-
POWER CONSUMPTION
less than 45 W
less than 1 W
less than 1 W
less than 1 W
LED COLOR
GREEN
AMBER
AMBER
AMBER
OFF
VIDEO
ACTIVE
OFF
OFF
OFF
-less than 1 W

- 3 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
• Do not modify original design without obtaining written
permission from manufacturer or you will void the
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
• Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.

- 4 -
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
720x400
70Hz
H – 35.00 864 640 64 64 96 224
V – 66.667Hz 525 480 3 3 39 45
640x480
60Hz
H – 37.50 840 640 16 64 120 200
V – 75.0Hz 500 480 1 3 16 20
640x480
65Hz
H – 31.500 900 720 18 108 54 180
V + 70.156Hz 449 400 12 3 34 49
640x480
75Hz
H – 35.162 896 720 34 40 102 176
V – 59.901Hz 587 480 12 2 93 107 720x480
60Hz
H +- 35.156 1024 800 24 72 128 224
V + 56.250Hz 625 600 1 2 22 25 800x600
56Hz
H + 37.879 1056 800 40 128 88 256
V + 60.317Hz 628 600 1 4 23 28 800x600
60Hz
H + 48.077 1040 800 56 120 64 240
V + 72.188Hz 666 600 37 6 23 66 800x600
72Hz
H + 46.875 1056 800 16 80 160 256
V + 75.0Hz 625 600 1 3 21 25 800x600
75Hz
H – 49.727 1152 832 32 64 224 320
V – 74.553Hz 667 624 3 3 37 43
832x624
(MAC16”)
75Hz
H – 48.363 1344 1024 24 136 160 320
V – 60.004Hz 806 768 3 6 29 38 1024x768
60Hz
H – 56.476 1328 1024 24 136 144 304
V – 70.069Hz 806 768 3 6 29 38 1024x768
70Hz
H + 60.023 1312 1024 16 96 176 288
V + 75.029Hz 800 768 1 3 28 32 1024x768
75Hz
H – 60.241 1328 1024 32 96 176 304
V – 74.927Hz 804 768 3 3 30 36
1024x768
(MAC19)
75Hz
H + 67.500 1600 1152 64 128 256 448
V + 75.000Hz 900 864 1 3 32 36 1152x864
75Hz
H – 68.681 1456 1152 32 128 144 304
V – 75.062Hz 915 870 3 3 39 45
1152x870
(MAC21)
75Hz
H – 61.795 1504 1152 30 128 194 352
V – 65.950Hz 937 900 2 4 31 37 1152x900
66Hz
H – 71.732 1472 1152 16 96 208 320
V – 76.068Hz 943 900 2 8 33 43 1152x900
75Hz
H + 31.216 1480 1170 37 129 144 310
V + 50.026Hz 624 584 3 3 34 40 1170x584
50Hz
H + 60.000 1800 1280 96 112 312 520
V + 60.000Hz 1000 960 1 3 36 40 1280x960
60Hz
H + 63.981 1688 1280 48 112 248 408
V + 60.020Hz 1066 1024 1 3 38 42 1280x1024
60Hz
H + 79.976 1688 1280 16 144 248 408
V + 75.025Hz 1066 1024 1 3 38 42 1280x1024
75Hz
Sync
Polarity Frequency
Dot
Clock
Back Porch
(F)
Blanking time
(B)
Resolution
28.350
25.175
30.240
31.500
31.505
36.000
40.000
50.000
49.500
57.285
65.000
75.000
78.750
80.000
108.000
100.000
92.940
105.590
46.200
108.000
108.000
135.000
TIMING CHART
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H – 31.469 800 640 16 96 48 160
V – 59.940Hz 525 480 10 2 33 45
Sync Duration
(D)
Front Porch
(C)
Video Active Time
(A)
Total Period
(E)

TIMING CHART
- 5 -
VIDEO
SYNC
B
D
CFE
A
OPERATING INSTRUCTIONS
FRONT VIEW REAR VIEW
Front Control Panel
SONY
MENU
OK
Power Connector
See front control panel
D-Sub Signal
Connector
1. Power switch and indicator
This switch turns the dislay on and off.
This power indicator lights up in green when the
display is turned on, and lights up in orange when
the monitor is in power saving mode.
2. MENU Button
This button display or close the main menu.
3. Buttons
These buttons function as the buttons when
selecting the menu items and making adjustments.
4. OK Button
This button select the item or executes the settings
in the menu.
5. Button(Backlight control)
MENU
OK
12345

- 6 -
WIRING DIAGRAM
GENESS
J705
J702
J710
CN3
CN1
CN2 CN4
Connector Ass’y
P/N: 190027329

- 7 -
D-SUB
GM2121
including
(MCU/ADC /LVDS )
Flash
Memory
LCD Module
R,G,B
differential
LVDS (Low Voltage Differential Signaling)
Data 8 Bit Address
LIPS
5V
AVD D 3.3V DVDD 3.3V
5V
AC Input
AVD D 2.5V DVDD 2.5V
3.3V
Reg.
AVD D3.3V DVDD3.3V
2.5V
Reg.
AVD D2.5V DVDD2.5V
5V 5V
12V
R,G,B, H/V Sync
BLOCK DIAGRAM

- 8 -
ADJUSTMENT
1. Procedures of how to go to service mode.
1) Enter the service mode of this unit by turning on the
power while pressing and holding the " " key
simultaneously.
2) Press "MENU" key----MAINTAIN.
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
monitor then enters the normal mode.
To enter the service again, repeat the procedure
described above.
Note
W/B readjustment is required after the panel, board
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB reset
before W/B adjustment.
2. Setup
1) Prepare timing and pattern data for a signal
generator according to the Sony timin specifications.
2)
Connect a monitor video cable to the signal generator.
3) Put Color Analyzer(ex. CA-110) 50cm away from the
monitor, specify it vertically in the center of the
display, and adjust the focus to the optimum level
using an eyepiece.
4) Put the monitor and Color Analyzer(ex. CA-110) in a
light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
3. Operation
Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70
and 100 respectively. After that, the default data of the
color temperature to be adjusted is set.
4. Warm up time
Warm up for 30 minutes before performing any
adjustment.
5. Adjustment for White Balance
a. Display Full white pattern at SXGA/60Hz.
b. Set up [SERVICE MODE].
c. Click "INITIAL EEPROM".
d. Click "WHITE BALANCE".
6. 9300K color adjustment
a. Select "9300K" in "COLOR TEMP" and enter.
b. Use a 35% IRE white video field in the primary
mode.
c. Adjust "SUB CONTRAST " to secure the color
temperature.
d. Press "OK" key to exit adjust mode.
7. 6500K color adjustment
a. Select "6500K" in "COLOR TEMP" and enter.
b. Repeat the adjustment procedure as steps b to d at
9300K.

- 9 -
GENESS
SONY
1
2
3
11
8
10
9
7
6
4
5
EXPLODED VIEW

- 10 -
EXPLODED VIEW PARTS LIST
Ref. No.
1
1
2
3
3
4
5
6
7
7
8
9
10
11
11
Part No.
X40426241
X40430951
180553911
X40424691
X40430941
X40414641
X40414651
A1410606A
409440521
409440531
190027329
A1410596A
A1410597A
409440631
409440651
Description
BEZEL ASSY (Silver)
BEZEL ASSY (Black)
LCD PANEL
BACK CABINET ASSY (Silver)
BACK CABINET ASSY (Black)
CENTER CABINET ASSY
STAND ASSY
H MOUNT
BOTTOM VENT COVER (Silver)
BOTTOM VENT COVER (Black)
CONNECTOR ASSY
G MOUNT
A MOUNT
REAR COVER (Silver)
REAR COVER (Black)

Part No. Description
182711021 D-SUB CABLE
182711821 POWER-SUPPLY CORD SET (E, U/C)
182712021 POWER-SUPPLY CORD SET (AEP)
182712221 POWER-SUPPLY CORD SET (CH)
182711921 POWER-SUPPLY CORD SET (JAPAN)
409895502 CD-ROM (MANUAL)
409895311 QUICK SETUP GUIDE (E, CH, U/C)
409895321 QUICK SETUP GUIDE (AEP)
409895301 QUICK SETUP GUIDE (JAPAN)
409440101 PROTECTION BAG
409441701 CUSHION
409902401 INDIVIDUAL CARTON
-11-
ACCESSORIES & PACKING MATERIALS

Sony EMCS Corporation Ichinomiya Tec Feb. 2004
9-878-221-01 2004AR02-1