Sony SU-WL850 Service manual

E-627-100-11(1)
SU-WL850
Wall-Mount
Bracket
Installation Information GB
安装信息 CS
安裝資訊 CT
Thông tin Lắp đặt VN
Informations d’installation FR
Информация об установке RU
 TH
Informasi Pemasangan ID

− 2 (GB) −
Installation Information for
Using Sony Wall-Mount Bracket (SU-WL850)
Supported models*:
KD-75X90xxH / 65X90xxH / 55X90xxH
FW-75BZ40H / 65BZ40H / 55BZ40H
* In the actual model names, the “xx“ indicates numbers and/or characters specific to each model.
To Customers
For product protection and safety reasons, Sony strongly recommends that installation of your TV or
LCD Monitor be performed by Sony dealers or licensed contractors. Do not attempt to install it
yourself.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required for installing this product, especially to determine the
strength of the wall for withstanding the TV’s or LCD Monitor’s weight. Be sure to
entrust the attachment of this product to the wall to Sony dealers or licensed
contractors and pay adequate attention to safety during the installation. Sony is not
liable for any damage or injury caused by mishandling or improper installation.
For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV or LCD
Monitor Setup Guide and the directions in this manual.

− 3 (GB) −
GB
Wall-Mount Bracket
On Safety
Thank you for purchasing this product.
To Customers
Installing the TV or LCD Monitor to the
Wall
WARNING
PROFESSIONAL INSTALLATION REQUIRED
This product should only be installed by
a professional installer who is trained to
determine the strength of the wall for
withstanding the TV’s or LCD Monitor’s
weight. If it is not properly secured
during installation, the TV or LCD Monitor
may fall and cause serious injury. Sony is
not liable for any damage or injury
caused by mishandling or improper
installation, or installing any other than
the specified product. Your Statutory
Rights (if any) are not affected.
To Sony dealers
Sufficient expertise is required for
installing this product. Be sure to read
this instruction manual thoroughly to do
the installation work safely. Sony is not
liable for any damages or injury caused
by mishandling or improper installation.
Please give this manual to the customer
after installation.
This instruction manual shows the correct
handling of the product and important
precautions necessary to prevent accidents.
It is your responsibility to read, thoroughly
understand, and follow all instructions in this
instruction manual. Failure to do so may
result in serious personal injury or property
damage, and may void the warranty. Keep
this manual available for future reference.
Products by Sony are designed with safety in
mind. If the products are used incorrectly,
however, it may result in a serious injury
through fire, electric shock, the product
toppling over, or the product dropping. Be
sure to observe the precautions for safety to
prevent such accidents.
CAUTION
Specified products
This Wall-Mount Bracket is designed for use
with the products specified TVs or LCD
Monitors. For TVs or LCD Monitors, refer to
their Reference Guide to verify that the
Wall-Mount Bracket can be used.
To Customers
WARNING
If the following precautions are not
observed, serious injury or death
through fire, electric shock, or the
product dropping can result.
Be sure to subcontract
the installation to
licensed contractors and
keep small children away
during the installation.
If the Wall-Mount Bracket or the TV or LCD
Monitor is not installed correctly, the
following accidents may occur. Be sure
licensed contractors carry out installation.
The TV or LCD Monitor may fall and cause
a serious injury such as a bruise or a
fracture.
If the wall on which the Wall-Mount
Bracket is installed is unstable, uneven, or
not perpendicular to the floor, the unit
may fall and cause injury or property
damage. The wall should be capable of
supporting a weight of at least six times
the TV or LCD Monitor weight.
(Refer to your TV’s or LCD Monitor’s
Reference Guide for its weight.)
If the installation of the Wall-Mount
Bracket on the wall is not sufficiently
sturdy, the unit may fall and cause injury or
property damage.
Be sure to subcontract
moving or dismounting
of the TV or LCD Monitor
to licensed contractors.
If persons other than licensed contractors
transport or dismount the TV or LCD Monitor,
it may fall and cause injury or property
damage. Be sure that two or more persons
(three or more persons for 75 inches and
above TV or LCD Monitor set) carry or
dismount the TV or LCD Monitor.
Do not remove screws,
etc., after mounting the
TV or LCD Monitor.
If you do so, the TV or LCD Monitor may fall
and cause injury or property damage.
Do not make alterations
to the parts of the Wall-
Mount Bracket.
If you do so, the Wall-Mount Bracket may fall
and cause injury or property damage.
Do not mount any
equipment other than
the specified product.
This Wall-Mount Bracket is designed for use
with the specified product only. If you mount
equipment other than specified, it may fall or
break, and cause injury or property damage.
Do not apply any load
other than the TV or LCD
Monitor on the Wall-
Mount Bracket.
Do not shake the TV or
LCD Monitor left/right,
up/down.
If you do so, the TV or LCD Monitor may fall
and cause injury or property damage.
Do not lean on or hang
from the TV or LCD
Monitor.
Do not lean on or hang from the TV or LCD
Monitor as it may fall on you and cause
serious injury.
CAUTION
If the following precautions are not
observed, injury or property damage
may occur.
Be careful to not pinch your fingers while
handling the Wall-Mount Bracket or
swiveling the TV or LCD Monitor set.
While swiveling the TV or LCD Monitor set,
handle it with caution and take care not to
hit any people nearby.
Be sure to store the unused parts in a safe
place for future use.
Keep them away from children.
Do not handle the
product with excessive
force during cleaning or
maintenance.
Do not apply excessive force on the topside
of the TV or LCD Monitor. If you do so, the TV
or LCD Monitor may fall and cause injury or
property damage.
Precautions
If you use the TV or LCD Monitor installed
on the Wall-Mount Bracket for a long time,
the wall behind or above the TV or LCD
Monitor may become discolored or the
wallpaper may come unstuck, depending
on the material of the wall.
If the Wall-Mount Bracket is removed after
installing it on the wall, the screw holes are
left.
Do not use the Wall-Mount Bracket in a
place where it is subjected to mechanical
vibrations.

− 4 (GB) −
Installing the Wall-
Mount Bracket
To Sony Dealers
WARNING
The following instructions are for Sony
dealers only. Be sure to read safety
precautions described above and pay
special attention to safety during the
installation, maintenance and checking
of this product.
Do not install the Wall-
Mount Bracket on wall
surfaces where the
corners or the sides of
the TV or LCD Monitor
protrude away from the
wall surface.
Do not install the Wall-Mount Bracket on wall
surfaces such as a pillar, where the corners
or the sides of the TV or LCD Monitor
protrude away from the wall surface. If a
person or object happens to hit the
protruded corner or side of the TV or LCD
Monitor, it may cause injury or property
damage.
Do not install the TV or
LCD Monitor over or
under an air-conditioner.
If the TV or LCD Monitor is exposed to water
leaks or air current from an air conditioner
for a long time, it may cause a fire, an electric
shock or a malfunction of the TV or LCD
Monitor.
Be sure to install the
Wall-Mount Bracket
securely to the wall
following the instructions
in this instruction
manual.
If any of the screws are loose or fall out, the
Wall-Mount Bracket may fall and cause injury
or property damage. Be sure to use the
appropriate screws for the material of the
wall and install the unit securely using four
screws of 8 mm diameter (or equivalent).
Be sure to use the
supplied screws and
attachment parts
properly following the
instructions given in
this instruction
manual. If you use
substitute items, the
TV or LCD Monitor may
fall and cause bodily
injury to someone or
damage to the TV or
LCD Monitor.
Be sure to assemble the
bracket properly
following the instructed
procedure explained in
this instruction manual.
If any of the screws are loose or fall out, the
TV or LCD Monitor may fall and cause bodily
injury to someone or damage to the TV or
LCD Monitor.
Be sure to tighten the
screws securely in the
designated position.
If you fail to do so, the TV or LCD Monitor
may fall and cause bodily injury to someone
or damage to the TV or LCD Monitor.
Be careful not to subject
the TV or LCD Monitor to
shock during installation.
If the TV or LCD Monitor is exposed to shock,
it may fall or break apart. This may cause
injury.
Be sure to install the TV
or LCD Monitor on a wall
that is both
perpendicular and flat.
If you fail to do so, the TV or LCD Monitor
may fall and cause injury.
After proper installation
of the TV or LCD Monitor,
secure the cables
properly.
If people or objects get tangled with cables,
this may result in injury or damage to the TV
or LCD Monitor.
Do not allow the AC
power cord (mains lead)
or the connecting cable
to be pinched.
If the AC power cord (mains lead) or the
connecting cable is pinched between the
unit and the wall or is bent or twisted by
force, the internal conductors may become
exposed and cause a short circuit or an
electrical break. This may cause a fire or an
electric shock.
The screws needed to
secure the Wall-Mount
Bracket to the wall are
not supplied.
Use the appropriate screws for the wall
material and structure when mounting the
Wall-Mount Bracket.

− 5 (GB) −
GB
Before getting started
Firstly, check the type of the wall to install the TV or LCD Monitor.
What is your wall made of?
Dry wall with studs
Precautions
 Maximum dry wall thickness:
16 mm.
 Ensure that the inner wood stud size is at
least 51 x 102 mm for common or
38 x 89 mm for nominal.
 Keep minimum 406 mm horizontal space
between fasteners.
Solid Concrete or Concrete Block
Precautions
 Mount the Wall-Mount Bracket directly
onto the solid concrete wall.
 Ensure that the thickness of solid concrete
wall is at least 203 mm.
 Ensure that the size of each concrete block
is at least 203 x 203 x 406 mm.

− 6 (GB) −
Preparing for installation
 Have the TV’s or LCD Monitor’s Reference
Guide and Setup Guide at hand before
installation.
 Confirm the installing position of your TV or
LCD Monitor.
 Prepare four screws of 8 mm diameter and
four proper washers (not supplied).
Select screws suitable for the material of the
wall.
Checking the parts
Supplied with SU-WL850
 Verify that all the parts are included.
WM1 (1) WM2 (1)
WM3 (4) M6 (4)
WT1 (6)
Supplied with the TV or LCD Monitor
VS Wall-Mount
Attachment (4)

− 7 (GB) −
GB
Tools needed
*1
5.5 mm 10 mm
*2
1.5 N·m
{15 kgf·cm}
*3
1.5 N·m
{15 kgf·cm}
(4)
*4
(4)
*2
8 mm x 60 mm
(4)
*4
*1 Only for dry wall with studs
*2 Only for solid concrete or concrete block
*3 Depending on models
*4 Be careful when selecting screws and washers
≤7.5 mm

− 8 (GB) −
Attaching TV or LCD Monitor to the Dry Wall with Studs
Dry wall with studs
WM1
Installing the Wall-Mount Bracket to the wall
1 Decide on the installation location.
Make sure that the wall has enough space for the TV or LCD Monitor and is capable of
supporting a weight of at least six times that of the TV or LCD Monitor.
Refer to the following table on installing the TV or LCD Monitor to the wall. Refer to your TV’s or
LCD Monitor’s Reference Guide for the TV’s or LCD Monitor’s weight.
*1

− 9 (GB) −
GB
g
f
(mm)
Model Name f*2
g
*2 (°)
KD-75X90xxH 1,674 961 363 -122* 84 288 15
FW-75BZ40H 1,674 961 363 -122* 85 288 15
KD-65X90xxH 1,450 833 362 -59* 82 286 18
FW-65BZ40H 1,450 833 362 -59* 83 286 18
KD-55X90xxH 1,231 710 362 3 82 286 20
FW-55BZ40H 1,231 710 362 3 83 286 20
* Bracket positioning is below the screen centre point.
TV or LCD Monitor installation dimensions table (mm)
Figures in the table may differ slightly depending on the installation.
*1 (Screen centre point)
*2 (Approx.)
Note
 When your TV or LCD Monitor is installed on the wall, the upper side of the TV or LCD Monitor slightly leans forward.

− 10 (GB) −
3 Align WM1 to the wall and
make four marks aligned with
the studs.
WM1
Note
 Use a level to check whether WM1 is level.
4 Drill upper pilot holes on the
marks.
75 mm
5.5 mm
Note
 Pilot holes must be drilled to a depth of 75 mm, using
a 5.5 mm diameter drill bit.
5 Install WM1 on the wall using
suitable screws (not supplied)
and washers (not supplied).
8 mm × 60 mm
Note
 Use a level to check whether WM1 is level.
Precaution
 Do not over-tighten wooden screw 8 mm × 60 mm.
Improper tightening could reduce the holding power
of wooden screw 8 mm × 60 mm.
Note
 We recommend you to check the
position of TV or LCD Monitor in the
viewing environment.
2
406 mm

− 11 (GB) −
GB
Preparing for the installation
of the TV or LCD Monitor
Make sure to attach the Table-Top Stand
before installing the TV or LCD Monitor to the
wall by referring to the Setup Guide.
1 Remove the screws from the
rear of the TV or LCD Monitor.
Note
 Be sure to store the removed screws and unused
parts in a safe place, keeping them away from
children.
2 Attach the Wall-Mount
Attachment (supplied with the
TV or LCD Monitor) to the rear of
the TV or LCD Monitor (to make
it parallel with the wall).
VS
1.5 N·m
{15 kgf·cm}
6 Drill lower pilot holes on the
marks. (Refer step 4 for the drill
instruction.)
7 Fit the suitable screws and
washers to the holes.
Note
 Use a level to check whether the Wall-Mount Bracket
is level.
8 Pull out the arm of the bracket
to the end.

− 12 (GB) −
Note
 Be sure to fasten the Wall-Mount Attachment when
attaching them to the TV or LCD Monitor.
Use only a flat head screwdriver to install the
Wall-Mount Attachment. Use of another tool might
result in over torqueing the Wall-Mount Attachment
and damaging the TV or LCD Monitor.
3 Attach WM3 .
WM3
4 Attach the WM2 to the TV or
LCD Monitor using
M6 .
M6
WM2
5 Detach the Table-Top Stand
from the TV or LCD Monitor.
 Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top
Stand securely with both hands while
the other people lift up the TV or LCD
Monitor.
 Repeat the previous step and remove
the other side of the Table-Top Stand.
Note
 Three or more people are required to detach the
Table-Top Stand.
 Be careful not to use excessive force while detaching
the Table-Top Stand from the TV or LCD Monitor as it
may cause the TV or LCD Monitor set to fall resulting
in personal injury or physical damage to the TV or
LCD Monitor.
 Take care when handling the Table-Top Stand to
prevent damage to the TV or LCD Monitor.
 Be careful when lifting the TV or LCD Monitor as the
Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
 Take care when removing the Table-Top Stand from
the TV or LCD Monitor to prevent it from falling over
and damaging the surface that the TV or LCD Monitor
is sitting on.

− 13 (GB) −
GB
Installing the TV or LCD
Monitor on the wall
1
2
3 Screw the left and right side of
the Wall-Mount Bracket.
M6
M6

− 14 (GB) −
4
5 When moving the TV or LCD
Monitor, hold it firmly from the
bottom.
6
WARNING
 Be sure that two or more persons (three or more
persons for 75 inches and above TV or LCD Monitor
set) hold the TV or LCD Monitor when carrying it.
Confirming the completion of
the installation
Check the following points.
 The cord and the cable are not twisted or
pinched.
WARNING
 Improper placement of the AC power cord (mains lead),
etc. may cause fire or electric shock through a short
circuit. Be sure to confirm the completion of the
installation for safety.
Other information
When removing the TV or LCD Monitor,
reverse the previous installation procedure.
WARNING
 Be sure that two or more persons (three or more persons
for 75 inches and above TV or LCD Monitor set) hold the
TV or LCD Monitor when removing it.

− 15 (GB) −
GB
Attaching the Wall-Mount Bracket to the Solid Concrete or
Concrete Block
Solid Concrete or Concrete Block
WM1
Installing the Wall-Mount Bracket to the wall
1 Decide on the installation location.
Make sure that the wall has enough space for the TV or LCD Monitor and is capable of
supporting a weight of at least six times that of the TV or LCD Monitor.
Refer to the following table on installing the TV or LCD Monitor to the wall. Refer to your TV’s or
LCD Monitor’s Reference Guide for the TV’s or LCD Monitor’s weight.
*1

− 16 (GB) −
g
f
(mm)
Model Name f*2
g
*2 (°)
KD-75X90xxH 1,674 961 363 -122* 84 288 15
FW-75BZ40H 1,674 961 363 -122* 85 288 15
KD-65X90xxH 1,450 833 362 -59* 82 286 18
FW-65BZ40H 1,450 833 362 -59* 83 286 18
KD-55X90xxH 1,231 710 362 3 82 286 20
FW-55BZ40H 1,231 710 362 3 83 286 20
* Bracket positioning is below the screen centre point.
TV or LCD Monitor installation dimensions table (mm)
Figures in the table may differ slightly depending on the installation.
*1 (Screen centre point)
*2 (Approx.)
Note
 When your TV or LCD Monitor is installed on the wall, the upper side of the TV or LCD Monitor slightly leans forward.

− 17 (GB) −
GB
Note
 We recommend you to check the
position of TV or LCD Monitor in the
viewing environment.
2 Align WM1 to the wall and
make four marks.
WM1
Note
 Use a level to check whether WM1 is level.
3 Drill pilot holes on the marks.
10 mm
75 mm
4
5 Install WM1 on the wall using
suitable screws (not supplied)
and washers (not supplied).
8 mm × 60 mm
Note
 Use a level to check whether the Wall-Mount Bracket
is level.
Precaution
 Do not over-tighten wooden screw 8 mm × 60 mm.
Improper tightening could reduce the holding power
of wooden screw 8 mm × 60 mm.

− 18 (GB) −
6 Pull out the arm of the bracket
to the end. Preparing for the installation
of the TV or LCD Monitor
Make sure to attach the Table-Top Stand
before installing the TV or LCD Monitor to the
wall by referring to the Setup Guide.
1 Remove the screws from the
rear of the TV or LCD Monitor.
Note
 Be sure to store the removed screws and unused
parts in a safe place, keeping them away from
children.
2 Attach the Wall-Mount
Attachment (supplied with the
TV or LCD Monitor) to the rear of
the TV or LCD Monitor (to make
it parallel with the wall).
VS
1.5 N·m
{15 kgf·cm}

− 19 (GB) −
GB
Note
 Be sure to fasten the Wall-Mount Attachment when
attaching them to the TV or LCD Monitor.
Use only a flat head screwdriver to install the
Wall-Mount Attachment. Use of another tool might
result in over torqueing the Wall-Mount Attachment
and damaging the TV or LCD Monitor.
3 Attach WM3 .
WM3
4 Attach the WM2 to the TV or
LCD Monitor using M6 .
M6
WM2
5 Detach the Table-Top Stand
from the TV or LCD Monitor.
 Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top
Stand securely with both hands while
the other people lift up the TV or LCD
Monitor.
 Repeat the previous step and remove
the other side of the Table-Top Stand.
Note
 Three or more people are required to detach the
Table-Top Stand.
 Be careful not to use excessive force while detaching
the Table-Top Stand from the TV or LCD Monitor as it
may cause the TV or LCD Monitor set to fall resulting
in personal injury or physical damage to the TV or
LCD Monitor.
 Take care when handling the Table-Top Stand to
prevent damage to the TV or LCD Monitor.
 Be careful when lifting the TV or LCD Monitor as the
Table-Top Stand is detached, the Table-Top Stand
may topple over and cause personal injury.
 Take care when removing the Table-Top Stand from
the TV or LCD Monitor to prevent it from falling over
and damaging the surface that the TV or LCD Monitor
is sitting on.

− 20 (GB) −
Installing the TV or LCD
Monitor on the wall
1
2
3 Screw the left and right side of
the Wall-Mount Bracket.
M6
M6