Sony STR-DE135 User manual

MICROFILM
SERVICE MANUAL
FM STEREO/FM-AM-RECEIVER
US Model
AEP Model
UK Model
STR-DE135
SPECIFICATIONS
Photo: US model
Audio power specifications (US model)
POWER OUTPUT ANDTOTAL HARMONIC DISTORTION
With 8-ohm load, both channels driven, from 20 – 20,000 Hz,
rated 100 watts per channel minimum RMS power, with no
more than 0.09 % total harmonic distortion from 250 milli-
watts to rated output.
Amplifier section
Stereo mode (8 ohms at 20 Hz – 20 kHz less than
0.09 % total harmonic distortion)
100 W + 100 W (US model)
(DIN 1 kHz, 4 ohms)
60 W + 60 W (AEP, UK models)
Frequency response TV/SAT, CD, MD/TAPE, VIDEO
(US model)
TV/LD, CD, MD/TAPE, VIDEO
(AEP, UK models)
10 Hz – 50 Hz ± 1 dB
Inputs Sensitivity Impedance S/N
CD,
MD/TAPE, 150 mV 50 78 dB
TV/SAT, kilohms
VIDEO (US model)
Sensitivity Impedance S/N
CD,
MD/TAPE, 150 mV 50 78 dB
TV/LD, kilohms
VIDEO (AEP, UK models)
outputs MD/TAPE REC OUT:
Voltage: 150 mV,
impedance: 10 kilohms
VIDEO AUDIO OUT:
Voltage: 150 mV,
impedance: 10 kilohms
PHONES: Accepts low and high
impedance headphones
Muting Full mute
BASS BOOST + 10 dB at 70 Hz
TONE ± 8 dB at 100 Hz and 10 kHz
Tuner Section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
Antenna terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
Sensitivity Mono: 18.3 dBf, 4.5 µV
Stereo: 38.3 dBf, 45 µV (US model)
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo: 38.3 dBf, 22.5 µV/75 ohms
(AEP, UK models)
Usable sensitivity 11.2 dBf, 2 µV (IHF) (US model)
11.2 dBf, 1 µV/75 ohms (IHF)
(AEP, UK models)
S/N Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz Mono: 0.3 %
Stereo: 0.5 %
Separation 45 dB at 1kHz
Frequency response 30 Hz – 15 kHz dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range 10 kHz interval*
530 – 1710 kHz
9 kHz interval
531 – 1710 kHz (US model)
531 – 1602 kHz (AEP, UK models)
+0.5
–2
– Continued on next page –

– 2 –
TABLE OF CONTENTS
1. SERVICING NOTES ............................................... 3
2. GENERAL ................................................................... 4
3. DISASSEMBLY ......................................................... 5
4. TEST MODE ............................................................... 7
5. DIAGRAMS
5-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 9
5-2. Printed Wiring Board – MAIN Board – ........................ 11
5-3. Schematic Diagram – MAIN Board (1/2) – .................. 13
5-4. Printed Wiring Boards
– DISPLAY Board/KEY Board/VOLUME Board/
TONE Board/POWER SWITCH Board –................... 15
5-5. Schematic Diagram
– PANEL Section – ......................................................... 19
5-6. Printed Wiring Boards
– PANEL Section – ......................................................... 23
5-7. Schematic Diagram
– MAIN Board (2/2)/SPK SWITCH Board/
SECONDARY Board/PRIMARY Board/
STANDBY TRANS Board – ....................................... 25
5-8. IC Pin Function Description ........................................... 26
6. EXPLODED VIEWS................................................ 28
7. ELECTRICAL PARTS LIST ............................... 31
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED
LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
Antenna Loop antenna
Intermediate frequency 450 kHz
Usable sensitivity 50 dB/m (at 1,000 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5 % (50 mV/m, 400Hz)
Selectivity At 10 kHz: 40 dB
At 9 kHz: 35 dB (US model)
35 dB (AEP, UK models)
* You can change the AM tuning interval between 9 kHz and 10kHz.
After tuning in any AM station, turn off the receiver. Hold down the
PRESET TUNING + button and press the 1/u(power) button.All pre-
set stations will be erased when you change the interval. To reset the
interval, repeat the procedure. (US model)
General
System Tuner section:
PLL quartz-locked digital
synthesizer system
Preamplifier section:
Low-noise NF type equalizer
Power amplifier section:
Pure-complementary SEPP
Power requirements 120 V AC, 60 Hz (US model)
230 V AC, 50/60 Hz
(AEP, UK models)
Power consumption 155 W (US model)
135 W (AEP, UK models)
AC outlets 1 switched, total 120 W/1A Max
(US, UK models)
switch 100 W max (AEP model)
Dimensions 430 ×144 ×306 mm
(17 × 56/8× 124/8inches)
Mass (Approx.) 8.1 kg (17 lb 13 oz) (US model)
6.7 kg (AEP, UK models)
Supplied accessories FM wire antenna (1)
AM loop antenna (1)
Remote commander (remote) (1)
Size AA (R6) batteries (2)
Specifications indicated are measured at 230 VAC, 50Hz.
(AEP, UK models)
Design and specifications are subject to change without notice.

– 3 –
SECTION 1
SERVICING NOTES
MODEL IDENTIFICATION
– Rear view –
12345
PART No.
MODEL PART No.
US model 4-216-802-0π
AEP model 4-216-802-1π
UK model 4-216-802-2π
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
TheAC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2VAC range are suit-
able. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground

– 4 –
SECTION 2
GENERAL
1I/ubutton
2TUNING +, – buttons (US model)
TUNING/CHAR +, – buttons
(AEP, UK models)
3NAME button (AEP, UK models)
4PRESET/TUNING +, – buttons
(US model)
PRESET/PTY SELECT +, – buttons
(AEP, UK models)
5DISPLAY button (AEP, UK models)
6RDS PTY button (AEP, UK models)
7AM button (US model)
RDS EON button (AEP, UK models)
Location of controls
•Front view –
8FM button (US model)
FM/AM button (AEP, UK models)
9VIDEO button
0TV/SAT button (US model)
TV/LD button (AEP, UK models)
!¡ MD/TAPE button
!™ BASS BOOST button and indicator
!£ SPEAKERS A, B ON/OFF buttons
!¢ PHONES jack
!∞ SHIFT button
!§ Numeric buttons
!¶ DIRECT button
!• MEMORY button (US model)
MEMORY/ENTER button
(AEP, UK models)
!ª FM MODE button
@º TUNER button
@¡ CD button
@™ VOLUME control
@£ MUTING button and indicator
@¢ TREBLE control
@∞ BASS control
@§ BALANCE control
345
1267
!∞
890!¡ !™
!£
!¢
!§!¶ !• !ª @º @¡ @™ @£
@¢
@∞
@§
•Rear view –

– 5 –
CASE
FRONT PANEL SECTION
Note: Follow the disassembly procedure in the numerical order given.
SECTION 3
DISASSEMBLY
1 two tapping screws
1 tapping screw
2 case
1 two tapping screw
s
2 three connectors
(CNP702 – 704)
3 screw
(BVTP3
× 8)
4 claw
5 front panel
section
3 four screws
(BVTP3
× 8)
4 claw
1 two flat wires
(CNS204, CNP404
)

– 6 –
REAR PANEL SECTION
MAIN BOARD
2 connector
(CNP901)
4 rear panel section
3 four screws
(BVTP3
× 8)
3 six screws
(BVTP3
× 8
)
1 flat wire
(CNS205)
2 connector
(CNS802)
2 two connectors
(CNP703, 704)
4 PC board holder
2 connector
(CNP801)
1 two flat wires
(CNS204, CNP404)
5 MAIN board
3 three screws
(BVTP3
× 8)
3 three screws
(BVTP3
× 8)
2 connector
(CNP702)

– 7 –
SECTION 4
TEST MODE
Fluorescent IndicatorTubeTest Mode
All fluorescent segments are tested.When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing two buttons of [TV/SAT] (US model)* and
[DIRECT] simultaneously, press the 1/ubutton to turn the
power ON.
2. All segments turn on at the same time, then each segment turns
on one after another.
3. The message “FINISH” appears when this test is complete.
*) AEP, UK models are [TV/LD]
AUTO-BETICAL Check Mode (AEP, UK models)
To auto-scanning and memories of RDS station.
Procedure:
1. While pressing the [MEMORY/ENTER] button, press the
1/ubutton to turn the power ON.
2. The message “AUTO BET” appears and each function is se-
lected one after another.
AMTuning Interval Selection Mode (US model)
Either 9 kHz step or 10 kHz step can be selected for the AM tun-
ing interval.
Procedure:
1. Set the FUNCTION to AM.
2. Press the 1/ubutton to turn the power OFF.
3. While pressing the [TUNING+] button, press the 1/ubutton to
turn the power ON.
4. Either the message “9k STEP” or “10k STEP” appears.
5. Select the desired step.
Software Version Display Mode
The software version is displayed.
Procedure:
1. While pressing two the buttons of [MD/TAPE] and [DIRECT]
simultaneously, press the 1/ubutton to turn the power ON.
2. The software version is displayed.

– 8 –
• Circuit Boards Location
SECTION 5
DIAGRAMS
POWER SWITCH board
PRIMARY board
SECONDARY board
STANDBY TRANS
board
DISPLAY board
VOLUME board
TONE board
KEY board
SPK SWITCH
board
MAIN board

– 9 – – 10 –
5-1. NOTES FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
•X: parts extracted from the component side.
•b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
•Indication of transistor.
B
These are omitted.
CE
Q
• Waveforms
– MAIN Board –
1IC1 !¢ (XO)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•¢: internal component.
•2: nonflammable resistor.
•C: panel designation.
Note: The components identified by mark !or dotted line
with mark !are critical for safety.
Replace only with part number specified.
•U: B+ Line.
•V: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
• Voltagesaretakenwith aVOM(Inputimpedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F: FM
1.6 Vp-p
4.33 MHz
– DISPLAY Board –
1IC201 #∞ (X2)
5.4 Vp-p
4.19 MHz
B
These are omitted.
CE
Q

STR-DE135
C757
(AEP,UK)
C707
(AEP,UK)
– 11 – – 12 –
5-2. PRINTED WIRING BOARD – MAIN Board –
• See page 8 for Circuit Boards Location.
D421 F-5
D710 I-11
D721 H-5
D722 H-5
D723 H-6
D724 I-5
D801 I-7
D802 D-12
D804 I-7
D820 C-12
D821 C-12
D822 C-12
D823 C-12
D951 A-10
D952 A-10
D953 A-10
D954 A-10
D955 A-10
D956 A-10
IC1 D-1
IC401 C-4
IC403 E-3
IC701 E-7
IC801 C-6
IC802 C-6
IC803 B-7
IC804 C-7
IC950 A-7
Q303 E-3
Q304 D-3
Q401 F-5
Q402 F-5
Q451 E-5
Q452 F-5
Q701 G-8
Q702 G-8
Q703 H-8
Q704 F-8
Q710 I-12
Q720 G-7
Q721 I-5
Q722 H-6
Q723 I-5
Q751 C-8
Q752 D-8
Q753 E-8
Q754 C-8
Q770 B-7
Q801 H-7
Q802 C-13
Q951 A-7
• Semiconductor
Location
Ref. No. Location
(Page 17)
(Page 24)
(Page
23)
(Page 23)
(Page 15)
(Page
23)
(Page
23)

STR-DE135
5-3. SCHEMATIC DIAGRAM – MAIN Board (1/2) – • See page 10 for Waveform. •See page 21 for IC Block Diagrams.
– 13 – – 14 –
(Page
25)
(Page
25)
(Page 20)
(Page 19)
(Page
25)
The components identified by mark !or dotted
line with mark !are critical for safety.
Replaceonly with partnumber specified.

STR-DE135
– 15 – – 16 –
5-4. PRINTED WIRING BOARDS – PANEL Section – • See page 8 for Circuit Boards Location.
D201 A-3
D202 A-3
D203 A-3
D204 B-3
D223 A-10
D224 A-10
IC201 B-6
IC202 A-1
IC203 B-11
Q201 B-3
Q202 B-3
• Semiconductor
Location
Ref. No. Location
(Page 11)
(Page 17)
(Page
17)

STR-DE135
– 17 – – 18 –
(Page 18)
(Page 11)
(Page 15)
(Page 16)
(Page 17)

STR-DE135
– 19 – – 20 –
5-5. SCHEMATIC DIAGRAM – PANEL Section – • See page 10 for Waveform. • See page 22 for IC Block Diagram.
100k
(Page 14)
(Page
13)
The components identified by mark !or dotted
line with mark !are critical for safety.
Replaceonly with partnumber specified.

STR-DE135
– 21 – – 22 –
• IC Block Diagrams
– MAIN Board –
IC1 BU1922 (AEP, UK models)
IC401 LC78212
QUALITY BIT
GENERATOR
DEFFERENTIAL
DECODER
BIPHASE
SYMBOL
DECODER
OSCILLATOR
AND
DIVIDER
57kHz
BANDPASS
(8th ORDER)
CONTAS LOOP
VARIABLE AND
FIXED DIVIDER
REFERENCE
VOLTAGE
ANTI-
ALIASING
FILTER
CLOCKED
COMPARATOR
TEST LOGIC AND OUTPUT
SELECTOR SWITCH
RECONSTRUCTION
FILTER
141516 13 12 11 10 9
321 4 5 6 7 8
CLOCK REGENERATION
AND SYNC
VP1
RDCL TS7 OSCO OSCI V
DDD
V
SSD
TEST TSTL
D
QUAL
RDDA
Vref
MUX
V
DDA
V
SSA
CIN
SCOUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
CONTROL
LATCH
SHIFT RESISTOR
LEVEL SHIFT
CL
DI
CE
VEE
OUT
IN
OUT
IN
OUT
IN
VSS
S
RESET
VDD
OUT
ININ
OUT
IN
OUT
IN
IC950 NJM2103D
1
2
3
45
6
7
8
V+
VSB/SESIN
VSA
RESET
GND
OUTC
VSC
CR
VREF
+–
–+
–
+
–
+
Q
R S
IC701 µPC2581V
235
46798
1
MUTE
+ VOUT1 – VOUT1
COMP1
MF1
IN1
GND
IN2
NF2
COMP2
– VOUT2 + VOUT2
VCC1 VCC2
VEE
PROTECTOR
BIAS CIRCUIT
REG DRIVE PRE
DRIVE
11
10 12 13 1514
DRIVE
PRE
DRIVE
– DISPLAY Board –
IC202 BA6208
1 2 3 4 5 6 7 89
NC
OUTPUT 2
Vcc
GND
NC
INPUT 2
INPUT 1
NC
MOTOR
DRIVE
MOTOR
DRIVE
REG
SWITCH
SWITCH
OUTPUT1

STR-DE135
– 23 – – 24 –
5-6. PRINTED WIRING BOARDS – SPK SWITCH Board/SECONDARY Board/PRIMARY Board/STANDBY TRANS Board –
• See page 8 for Circuit Boards Location.
(AEP)
(Page 12)
(Page 24)
(Page 12)
(Page 12)
(Page 12)
(Page 12)
(Page 23)

– 25 –
5-7. SCHEMATIC DIAGRAM – MAIN Board (2/2)/SPK SWITCH Board/SECONDARY Board/
PRIMARY Board/STANDBYTRANS Board –
STR-DE135
R742
1.2k 1/2W
R792
1.2k 1/2W
(Page 14)
(Page 14)
(Page 14)
The components identified by mark !or dotted
line with mark !are critical for safety.
Replaceonly withpartnumber specified.

– 26 –
5-8. IC PIN FUNCTION DESCRIPTION
•DISPLAY BOARD IC201 µPD78044FGF-115-3B9 (SYSTEM CONTROLLER, FL DRIVER)
Pin No. Pin Name I/O Description
1 to 7 DIG7 to DIG1 O Digit drive signal output to the fluorescent indicator tube (FL201)
8VDD — Power supply terminal (+5V)
9 S.CLK OSerial data transfer clock signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack
“L” active
10 S.DATA O Serial data output to the LC78212 (IC401), PLL IC on FM/AM tuner pack “L” active
11 PLL.DATA I Serial data input from the PLL IC on FM/AM tuner pack “L” active
12 S.CE (LC7822) O Serial chip enable signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack
“H” active
13 S.CE (LV1010) O Serial chip enable signal output terminal “L” active Not used (pull down)
14 REAR-RY O Relay drive signal output for the rear side speaker “H”: relay on Not used (open)
15 BRIDGE O Bridgeable relay drive signal output terminal “H”: relay on Not used (open)
16 PROTECT I Over load detect signal input from the protect circuit “L”: protect detect
17 RESET ISystem reset signal input from the reset signal generator (IC950, Q201) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
18 AUTO-STOP I Tuned display detection signal input from the FM/AM tuner pack “L”: tuned
19 STEREO-IN I Stereo detection signal input from the FM/AM tuner pack “L”: stereo
20 AVSS — Ground terminal (for A/D converter analog system)
21 SP-RY O Relay drive signal output for the speaker protect “H”: relay on
22 SURR-RY O Relay drive signal output for the surround speaker “H”: relay on Not used (pull down)
23 POWER-RY O Relay drive signal output for the power on/off control “H”: relay on
24 SIGNAL I FM and AM signal meter voltage detection signal input from the FM/AM tuner pack
25 A/D-4 IKey input terminal (A/D input) S210 (NAME) key input
(Used for the AEP and UK models only)
26 A/D-3 IKey input terminal (A/D input) S231 to S239 (BASS BOOST, MUTING, SHIFT, 0, MEMORY
or MEMORY/ENTER, CD, MD/TAPE, TV/SAT or TV/LD, RDS PTY) keys input
(S239 RDS PTY key: used for the AEP and UK models only)
27 A/D-2 IKey input terminal (A/D input) S221 to S230 (FM or FM/AM, 6, 5, 4, 7, 8, 9, FM MODE,
VIDEO, TUNER) keys input
28 A/D-1 IKey input terminal (A/D input) S211 to S220 (DISPLAY, AM or RDS EON, 3, 2, 1, TUNING
or TUNING/CHAR –/+, PRESET TUNING or PRESET/PTY SELECT –/+, DIRECT) keys input
(S211 DISPLAY key: used for the AEP and UK models only)
29 AVDD — Power supply terminal (+5V) (for A/D converter analog system)
30 AVREF I Reference voltage (+5V) input terminal (for A/D converter)
31 RDS DATA IN I RDS data input from the RDS decoder (IC1) (Used for the AEP and UK models only)
32 OPEN — Not used (open)
33 GND — Ground terminal
34 X1 I Main system clock input terminal (4.19 MHz)
35 X2 O Main system clock output terminal (4.19 MHz)
36 WOFER RLY O Relay drive signal output for the woofer speaker “H”: relay on Not used (open)
37 LED SELECT O LED select signal output terminal “H” active Not used (open)
38 DOLBY LED O LED drive signal output terminal “H”: LED on Not used (open)
39 C STUDIO LED O LED drive signal output terminal “H”: LED on Not used (open)
40 HALL LED O LED drive signal output terminal “H”: LED on Not used (open)
41 ENTER LED I Not used (fixed at “L”)
42 VOL DOWN O Motor drive signal (volume down direction) output to the volume motor drive (IC202)
“H” active
43 VOL UP O Motor drive signal (volume up direction) output to the volume motor drive (IC202)
“H” active

– 27 –
Pin No. Pin Name I/O Description
44 SYS-POWER I Power on/off switch (S240 I/u) input terminal “L” is input when key pressing
45 TUNER MUTE O Muting control signal output to the FM/AM tuner pack “H”: muting on
46 RDS CLK IN I RDS serial clock signal input from the RDS decoder (IC1)
(Used for the AEP and UK models only)
47 STOP I Power down detection signal input from the reset signal generator (IC950)
“L”: power down, normally: “H”
48 VSS — Ground terminal
49 SIRCS I Sircs remote control signal input from the remote control receiver (IC203)
50 MUTING LED O LED drive signal output of the MUTING indicator (D211) “L”: LED on
51 5.1 LED O LED drive signal output terminal “L”: LED on Not used (open)
52 VDD — Power supply terminal (+5V)
53 LOW BOOST O Control signal output of the BASS BOOST circuit and LED drive signal output of the BASS
BOOST indicator (D212) “H”: BASS BOOST on (LED on)
54 FUNC. MUTE O Audio line muting on/off control signal output terminal “H”: muting on
55 IC. MUTE O Muting on/off control signal output terminal “H”: muting on Not used (open)
56 VERSION I Setting terminal for the version
57, 58 S2, S1 O Not used (open)
59 to 61 LED1 to LED3 O LED drive signal output terminal “H”: LED on Not used (open)
62 to 70 S15 to S7 O Segment drive signal output to the fluorescent indicator tube (FL201)
71 VLOAD — Negative power supply terminal for the fluorescent indicator tube drive (–24V)
72 to 77 S6 to S1 O Segment drive signal output to the fluorescent indicator tube (FL201)
78 to 80 DIG10 to DIG8 O Digit drive signal output to the fluorescent indicator tube (FL201)

– 28 –
(1) CASE SECTION
SECTION 6
EXPLODED VIEWS
The components identified by
mark !or dotted line with mark
!are critical for safety.
Replace only with part number
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑↑
Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-4947-207-1 FOOT ASSY (F50150S) (AEP, UK)
1 X-4947-208-1 FOOT ASSY (F50150S) (US) 2 3-710-901-11 SCREW, TAPPING *3 4-998-206-21 CASE (413226)
2
2
3
2
1
1
#1
#1
#1
#1
Front panel
section
not supplied
not
supplied
not supplied
not
supplied
Chassis section