Sony KD-32NX200E User manual

- 1 -
SERVICE MANUAL AE-6D CHASSIS
MODEL COMMANDER DEST CHASSISNO.
KD-32NX200E RM-939 AEP SCC-Q85G-A
KD-32NX200E
RM-939

- 2 -
ATTENTION
APRES AVOIR DECONNECTE LE CAP DE’LANODE,
COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET
CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE
L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE
TUBE CATHODIQUE OU AU BLINDAGE DU TUBE
CATHODIQUE. ATTENTION !!
AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION
PROVENANT D’UN CHÁSSIS SOUS TENTION, UN
TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS
DE TOUT DÈPANNAGE LE CHÁSSIS DE CE RÈCEPTEUR EST
DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.
ATTENTION AUX COMPOSANTS RELATIFS Á
LA SECURITÈ!!
LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE
MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES
EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR-
TANCE CRITIQUE POUR LA SÈCURITÈDU FONCTIONNEMENT,
NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT
LE NUMÈRO DE PIÈCE EST INDIQUÈDANS LE PRÈSENT
MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
TABLE OF CONTENTS
Section Title Page Section Title Page
Caution .................... 3
Specifications .................... 4
Connectors .................... 5
Customer Service Menu .................... 6
Self Diagnostic Software .................... 10
1. GENERALAutomaticallyTuningthe TV .................... 13
Viewing a digital text service .................... 13
Viewing traditional teletext .................... 14
The EPG menu .................... 14
Using the TV menu system .................... 15
Viewing memory stick pictures .................... 16
Using the remote control with
VCR and DVD players .................... 17
Specifications .................... 18
Troubleshooting .................... 18
2. DISASSEMBLY
2-1. Rear Cover Removal .................... 19
2-2. Speaker Box Removal .................... 19
2-3. Chassis Removal and Refitting .................... 19
2-4. G1 Board Removal .................... 20
2-5. G Board Removal .................... 20
2-6. D2 Board Removal .................... 20
2-7. D1 Board Removal .................... 20
2-8. Service Position .................... 21
2-9. Wire Dressing 1 .................... 21
2-10. Wire Dressing 2 .................... 21
2-11. Wire Dressing 3 .................... 21
2-12. Picture Tube Removal .................... 22
BottomPlates .................... 23
3. SET-UP ADJUSTMENTS
3-1. BeamLanding .................... 24
3-2. Convergence .................... 25
3-3. FocusAdjustment .................... 27
3-4. Screen (G2), White Balance .................... 27
4. CIRCUIT ADJUSTMENTS
4-1. ElectricalAdjustments .................... 28
4-2. VolumeElectricalAdjustments .................... 32
4-3. Test Mode 2 .................... 33
5. DIAGRAMS
5-1. Block Diagrams (1) .................... 34
Block Diagrams (2) .................... 35
Block Diagrams (3) .................... 36
Block Diagrams (4) .................... 37
Block Diagrams (5) .................... 38
Block Diagrams (6) .................... 39
5-2. Circuit Board Location .................... 39
5-3. Schematic Diagrams and
Printed Wiring Boards .................... 39
* A Board PWB .................... 40
* A Board Schematic .................... 43
* B5 Board PWB ................. 52
* B5 Board Schematic .................... 53
* C1 Board PWB .................... 62
* C1 Board Schematic .................... 61
* H Board PWB .................... 62
* H Board Schematic .................... 63
* MS2 Board PWB .................... 62
* MS2 Board Schematic ............... 63
* D1 Board PWB .................... 64
* D1 Board Schematic .................... 65
* G1 Board PWB .................... 67
* G1 Board Schematic .................... 66
* D2 Board PWB .................... 67
* D2 Board Schematic .................... 68
* M2 Board PWB .................... 69
* M2 Board Schematic.................... 70
* G Board PWB .................... 72
* G Board Schematic ................... 71
* VM Board PWB ................. 72
* VM Board Schematic ................ 73
* F3 Board PWB .................... 74
* F3 Board Schematic .................... 73
* H3 Board PWB .................... 74
* H3 Board Schematic .................... 73
* J3 Board PWB .................... 74
* J3 Board Schematic .................... 75
* L Board PWB .................... 77
* L Board Schematic .................... 78
5-4. Semiconductors .................... 81
5-5. IC Blocks .................... 84
6. EXPLODEDVIEWS
6-1. Chassis .................... 87
6-2. PictureTube .................... 88
6-3. Modem .................... 89
7. ELECTRICAL PARTS LIST .................... 90
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE
CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE
ANODE CAP. WARNING !!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS
DIRECTLY CONNECTED TO THE POWER LINE.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY SHADING AND MARKED ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.

- 3 -
The circuit boards listed below [Table 1] used in these models may
have been processed using Lead Free Solder. The boards are
identified by the LF logo located close to the board designation e.g.
F1, H1 etc [ see examples ]. The servicing of these boards requires
special precautions to be taken as outlined below.
Table 1
CAUTION
Lead Free Soldered Boards example 1
example 2
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. Lead Free Solder is
available under the following part numbers :
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires
soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com
rebmuntraP retemaiD skrameR
91-500-046-7mm3.0gK52.0
02-500-046-7mm4.0gK05.0
12-500-046-7mm5.0gK05.0
22-500-046-7mm6.0gK52.0
32-500-046-7mm8.0gK00.1
42-500-046-7mm0.1gK00.1
52-500-046-7mm2.1gK00.1
62-500-046-7mm6.1gK00.1
draoB noitcnuF
3H dnaenohpdaeH,tupnIVAtnorF sehctiwSlortnoC

- 4 -
LEDOMMETI metsySnoisiveleT metsySoeretS egarevoClennahC metsySroloC
ET-BVD,K/D,H/G/B MACIN/NAMREG oeretS
30S-10S,2R-1R,21E-2E:FHV 92R-12R,96B-12B:FHU 02S-10S:VTELBAC 14S-12S:REPYH
,85.3CSTN,LAP )NIOEDIV(34.4CSTN LM@PM,2-GEPM
ebuTerutciP
nortinirTDF )sehcni23(mc28xorppA derusaemerutcipmc67xorppA( )yllanogaid noitcelfedeerged°201
tuptuOdnuoS
rekaepstfeLdnathgiR
refoowbuS
)SMR(W01x2)rewoPcisuM(W02x2
)SMR(W51x1)rewoPcisuM(W03x1
]RAER[slanimreTtuptuO/tupnI snoitacificepSlareneG
rotcennocoruEnip-12:1 )dradnatsCELENEC(
.slangisoediVdnaoiduArofstupnI .BGRrofstupnI oiduAdnaoediVVTfostuptuO .slangis
stnemeriuqeRrewoPV042-022
noitpmusnoCrewoPW451
rotcennocoruEnip-12:2
.slangisoediVdnaoiduArofstupnI .BGRrofstupnI oiduAdnaoediVVTfostuptuO .slangis
snoisnemiDmm095x5.544x019xorppA
thgieWgk76xorppA
rotcennocoruEnip-12:3
.slangisoediVdnaoiduArofstupnI .oediVSrofstupnI slangisoiduAdnaoediVrofstuptuO )elbatceles( seirosseccAdeilppuS rednammoCetomeR939-MR )2(yrettab6RdetangisedCEI elbachguorhtpooLFR
skcaJonohP oiduArofelbairavsrotcennoCtuptuO slangiS
tekcoSAICMCP eludoMsseccAlanoitidnoC serutaeFrehtO txeteleTegaP0002,POH,RND,FCD,FMCRD EBB,ybloDlautriV,yromeM
]TNORF[slanimreTtuptuO/tupnI lortnocderarfnI:metsyslortnocetomeR
kcajenohpdaeHkcajinimoerets
stnemeriuqerrewoP cdV3 noitangisedCEIseirettab2 )AAezis(6R
stupnioiduAskcajonohp
stupnioediVskcajonohp
tupnioediVSNIDnip4
.ecitontuohtiwegnahcottcejbuserasnoitacificepsdnangiseD
emaNledoM
metI E002XN23-DK
PAPFFO
PIPFFO
ytiroirPBGRNO
xoBrefooWNO
1tracSNO
2tracSNO
)4(nitnorFNO
3tracSNO
rotcejorPFFO
G/BmroNNO
ImroNFFO
K/DmroNNO
SUAmroNFFO
LmroNFFO
TASmroNFFO
MmroNFFO
txeteleTNO
oeretSmaciNNO

- 5 -
Connected Not Connected (open) * at 20Hz - 20kHz
Pin No 124 Signal Signal level
1Audio output B
(right) Standard level : 0.5V rms Output impedence : Less than 1kohm*
2Audio input B (right) Standard level : 0.5V rms Output impedence : More than 10kohm*
3Audio output A (left) Standard level : 0.5V rms Output impedence : Less than 1kohm*
4Ground (audio)
5Ground (blue)
6Audio input A
(left) Standard level : 0.5V rms Output impedence : More than 10kohm*
7Blue input 0.7 +/- 3dB, 75 ohms positive
8Function select
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9Ground (green)
10 Open
11 Green Green signal : 0.7 +/- 3dB, 75 ohms,
positive
12 Open
13 Ground (red)
14 Ground (blanking)
15
_ _ Red input 0.7 +/- 3dB, 75 ohms, positive
_ (S signal Chroma
input) 0.3 +/- 3dB, 75 ohms, positive
16 Blanking input
(Ys signal) High state (1-3V) Low state (0-0.4V) Input impedence : 75 ohms
17 Ground (video
output)
18 Ground (video
input)
19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
20
_ _ Video input 1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
_ Video input
Y (S signal) 1V +/- 3dB, 75ohms, positive sync 0.3V (-3+10dB)
21 Common ground
(plug, shield)
21 pin connector
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
Rear Connection Panel Front Connection Panel
noitarugifnocniptekcosoediVS
niPoN langiS leveLlangiS
1dnuorG-
2dnuorG-
3tupni)langisS(Y,mho57Bd3-/+V1 V3.0.cnySevitisop Bd01+3-
4tupni)langisS(CBd3-/+V3.0 evitisop,mho57 .cnyS
S-Video
socket
3

- 6 -
CUSTOMER SERVICE MENU
The Customer Service menu is provided in order to assist fault diagnosis when the customer reports a problem. The menu
can be invoked by the customer on request from the service technician or dealer during a telephone conversation. The
customer is then able to provide information regarding the current status of the set. The information gained can then help to
increase the number of problems that are solved on the first call out by the service engineer and also reduce the amount of
“No problem found” cases. The Customer Service Menu will be read only, preventing the customer from modifying the state
of the TV at this time.
1. Entering the Customer Service Menu
The customer service menu can be entered by simultaneously pressing the Menu
key on the Commander and the volume minus local key on the TV.
2. Description of Information available
The following information is available from the Customer Service Menu:
UNEMECIVRESREMOTSUCtxeND6EA
ledoM1002XN23-DK
emaNsissahC2txeND6EA
noisreVWS39B096V
leveLssenthgirB452
leveLtsartnoC504
leveLruoloC613
leveLssenprahS752
noitcudeResioN8diM
edoMCRD9001CRD
tamroFotuA01nO
noitcerroCtamroF11nO
metsySoiduA21oeretS
tceffEdnuoS31larutaN
loVrekaepS4103
loVenohpdaeH5106
egaptxenrof:tceleS

- 7 -
UNEMECIVRESREMOTSUCtxeND6EA
ecnalaBrekaepS610
TFA71nO
ycneuqerFrenuT81578276zHK
metsysVT91GB
metsysruoloC02LAP
yrevoceRAMME12nO
1rorrE220
2rorrE320
3rorrE420
4rorrE520
5rorrE620
egapsuoiverprof:tceleS
2.1 Item 1: Model
Displays the model name of the TV stored in NVM
· KV-29FQ86, KV-32FQ86, KV-36FQ86, KV-36FQ96
· KD-32NX200, KD-32NS200, KD-36NX200, KD-36NS200, KD-32DX150
2.2 Item 2: Chassis name
Displays the chassis name
· AE6(A),AE6D Next
2.3 Item 3: SW Version:
Displays the analogue software version the TV is running
· e.g.V690B3
2.4 Item 4: Brightness level
Displays the current NVM setting of the brightness level of the picture.
· Range : 0 63
2.5 Item 5: Contrast level
Displays the current NVM setting of the contrast level of the picture.
· Range : 0 63
2.6 Item 6: Colour level
Displays the current NVM setting of the colour level of the picture.
· Range : 0 63

- 8 -
2.7 Item 7: Sharpness level
Displays the current NVM setting of the sharpness level of the picture.
· Range : 0 63
2.8 Item 8: Noise reduction
Displays the current NVM setting of the Noise Reduction.
· Valid data : High, Mid, Low,Auto or Off
2.9 Item 9: DRC mode
Displays the current NVM setting of the DRC Mode.
· Valid data : Off, DRC 50, DRC 10
2.10 Item 10 : Auto Format
Displays the current NVM setting ofAuto Format.
· Valid data : Off, On
2.11 Item 11 : Format Correction
Displays the current NVM setting of Format Correction.
· Valid data : Off, On
2.12 Item 12: Audio system:
Displays information about the audio system of the selected source.
Note: For AE6D Next this displays information about the analogue signal only
· Sound muted: No sound.
· Mono: Mono sound received.
· NICAM stereo: NICAM encoded stereo sound signal received.
· Dual A: Channel A of a bilingual broadcast received.
· Dual B: Channel B of a bilingual broadcast received.
2.13 Item 13: Sound effect
Displays information about the current sound effect and graphic equaliser settings.
· Valid data : Personal, DolbyV, Dynamic, Natural
2.14 Item 14: Speaker Volume
Displays the current loudspeaker volume setting.
· Range : 0 63
2.15 Item 15: Headphone volume
Displays the current headphone volume setting.
· Range : 0 63
2.16 Item 16: Speaker Balance
Displays the current speaker balance setting.
· Range : -30 (full left) 0 (centre) +30 (full right)

- 9 -
2.17 Item 17: AFT:
Displays the current value of Automatic Fine Tuning function.
Note: For AE6D Next this displays information about the analogue signal only
· Valid data : Off, On, N/A (not available - displayed in AV mode)
2.18 Item 18:Tuner frequency:
Displays the current frequency of TV tuner (in KHz) or N/A (not available) inAV mode
Note: For AE6D Next this displays information about the analogue signal only
2.19 Item 19:TV system:
Displays information about the video system of the selected source.
Note: For AE6D Next this displays information about the analogue signal only
· BG: BG signal received.
· DK: DK signal received.
· I: PAL I signal received.
· L: SECAM L signal received.
· EXT: External signal received.
2.20 Item 20: Colour system:
Displays information about the colour system of the selected source.
Note: For AE6D Next this displays information about the analogue signal only
· Black and white: No colour carrier is being received.
· PAL: PAL signal received.
· SECAM: SECAM signal received.
· NTSC: NTSC signal received.
2.21 Item 21: Emma Recovery:
Displays current status of Emma Recovery (TT98: Enable/Disable).
Note: This is only displayed forAE6D Next chassis
· Valid data : Off, On
2.22 Items 22-26:
Displays the last 5 stored errors.

- 10 -
AE-6D SELF DIAGNOSTIC SOFTWARE
The identification of errors within theAE-6D chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the
event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this
method.
Flash Timing Example : e.g. error number 3
StByLED
ON ON ON
OFF OFF
metIcitsongaiD noitpircseD ybdnatSsemitfooN sehsalFDEL esuacelbaborP noitacoL smotpmySdetceteD
nonruttonseodrewoPthgiltonseoD .nideggulptonsidrocrewoP .tiucricneposiesuF
noemoctonseodrewoP VTehtotdeilppussirewopoN ytluafsiylppusrewopCA
)PCO(tnerrucrevOB+semit2 )draoB1D(.detrohssi)3018/2018Q(TUO.H )draoB1D(.detrohssi)6018Q(TEFytiraeniL )draoB1D(.detrohssiCIrewoP1088CI
noemoctonseodrewoP
detrohssahenilrewopnodaoL
deppotsnoitcelfeDlacitreVsemit4 )draoB1D(nepo7028RdeilppustonsiV51+ )draoB1D(nepo6028RdeilppustonsiV51- )draoBA(detrohssi1071CI
deppotssaheslupnoitcelfedlacitreV
detrohssahenilrewoP
egasseMrorrE DEL edoC
devreseR 10
)noitcetorPtnerruCrevO(PCO 20
)noitcetorPegatloVrevO(PVO 30
noitcetorPlacitreV 40
)edoMnoitcudorPnidelbasid,s03retfastratskcehc(BKAelbatsnU 50
noitcetorPlatnoziroH 60
noitcetorPrekaepS 70
rorrEsuBC2I 80
MVN,23C42TS.B-2M 90
draoB-A 01
draoB5B 11
draoB2J 21
draoBH 31
draoBSM 41
redoceDruoloCniaM.B-5B 51
dnekcaB,Q0512AXC.B-A 61
.corPdnuoS,1143PSM.B-A 71
.orciMlatigiD,rorrEAMME.B-N 81
desutoN 23-91

- 11 -
Device acknowledge is used to check IIC errors. Device acknowledge is checked by sending an IIC start sequence during CRT power on. Each
device is checked three times, if there is no acknowledge after each attempt, it will be regarded as an error.
There are three steps to check for errors.
1. IIC line 0
If all devices except the NVM have errors, IIC line 0 error is displayed.
2. Board check
If all devices mounted on one board have errors, board error is displayed.
3. Each devicecheck
If IIC line error and board error are not detected then the device with the error is displayed.
The detected errors can be displayed as follows :
1. Error Monitor Menu.
2. Error Reader.
Error Detection Monitor
1. Error Monitor Menu
Operating Time : 000167 h 45 min
Stored Errors :
1. A - B TU1350 Sub-Tuner
2. J - B TDA9320 Sub Col. Dec.
3. No Error Occured
4. No Error Occured
5. No Error Occured
Current Error :
A - B TU1350 Sub-Tuner
ERROR MONITOR
1. IGNORE ERRORS OFF ON OFF
Last menu Enter item

- 12 -
2. Error Reader Display
The error reader display is connected to the service connector to read actual error codes. The part number for the error reader display is
S-188-900-10. Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following
table.
edoCrorrE egasseMrorrE
h000deruccOrorrEoN
h1000C2I,rorrEsuB
h2001C2I,rorrEsuB
h3002C2I,rorrEsuB
h001draoB-A
h101.pxEtroP,5781AXC.B-A
h201renuT-niaM,xx06UT.B-A
h301FIniaM,6889ADT.B-A
h401dnekcaB,Q0512AXC.B-A
h501CAD,14188BM.B-A
h601.corPdnuoS,G1143PSM.B-A
h701.vnoC.anyD,0708AXC.B-A
h002draoB-5B
h102redoceDruoloCniaM.B-5B
h202redoceDruoloCbuS.B-5B
h302XDIM.B-5B
h402yarrAetaGamaronaP.B-5B
h502noitcudeResioN.giD.B-5B
h003draoB-H
h103kniLVA,8802DXC.B-H
h004draoB-J
h104hctiwSVA,5581AXC.B-2J
h204hctiwSVA,9412AXC.B-2J
h304renuT-buS,xx06UT.B-2J
h404FIbuS,6889ADT.B-2J
h005draoB-2M
h105MVN,23C42TS.B-2M
h006draoB-1SM
h106kcitSyromeM.B-1SM
h009draoB-N
h109AMME.B-N

- 13 -
Basic operation 10
OK
1
4
7
3
6
9
2
5
8
8
0
DIGITAL
DIGITAL
Viewing a digital text service
Most digital TV cha els broadcast i formatio via their text service. This digital service i cludes high quality text a d graphics alo g with adva ced avigatio optio s. Additio ally, this TV has access to dedicated text cha els tra smitted by the broadcasti g authorities. The appeara ce, co te t a d avigatio methods of all digital text services are decided by the broadcaster. For example, the RTL digital text service may look differe t to ZDF’s digital text. However, the digital text services curre tly available use simple avigatio methods based o the followi g butto s: The GUIDE butto to load up the digital text, The V, v, B a d b butto s (to move arou d the scree ),
The OK butto or the umbered butto s (to select items o scree ), The four coloured butto s (to access shortcuts).
Selecting a dedicated digital text channel Selecting a text service from other digital channels Normal text services may also be available o other digital cha els. This is sometimes i dicated by a small symbol o your TV scree , superimposed o the programme you are watchi g.
1.
Press the butto o the remote co trol to check if you are i digital mode. If you are watchi g a digital programme a I fo display appears o scree providi g brief details for the curre t a d ext programme. If the display does ot appear, press the DIGITAL/ butto to switch to digital
mode.
2.
Press the butto to remove the I fo display from the TV scree the select the programme umber that is broadcasti g the dedicated digital text cha el by usi g the umbered butto s o the remote co trol. If you do ot k ow the cha el umber of a dedicated digital text cha el, you ca use the ‘Cha el I dex me u’ to fi d o e. (Please refer to the ‘Cha el i dex me u’ sectio of this ma ual.)
3.
O ce the text page is displayed, follow the o -scree i structio s to obtai your required selectio . Note: O some pages the TV programme may also be displayed o the text scree . O - scree i structio s will i form you how to cha ge the displayed programme.
4.
If you are i structed to press ‘OK’ or ‘Select’ whe viewi g the text pages, press the OK butto .
5.
Whe you have fi ished viewi g the text service, press the butto to exit.
1.
Press the V, v, B, or b butto s to select the symbol, the press the OK
butto to display the chose i formatio .
2.
Alter atively, you may be i structed to use the umbered or coloured butto s o your remote co trol to display the various pages of text i formatio . If you are i structed to press ‘OK’ or ‘Select’ whe viewi g the text pages, press the OK butto .
3.
O ce the text i formatio is displayed, you ca access required i formatio by usi g the V, v, B, or b butto s, the coloured butto s a d/or the umbered
butto s o the remote co trol.
4.
Whe you have fi ished viewi g the text service, press the butto to exit.
Getting started 6
PROG
OK
1
4
7
3
6
9
2
5
8
0
5
1.
Whe you switch o the TV for the first time, the So y logo appears o the TV scree followed by the ‘Memory Stick’ logo, the the La guage/Cou try me u with the word ‘E glish’ highlighted. Press the V or v butto s o the
remote co trol to choose the la guage you require the press the OK butto to co firm.
2.
The word Cou try is ow highlighted. Press the V or v butto s to choose
the cou try i which you wish to operate the TV, the press the OK butto to co firm. The picture rotatio prompt appears. Sometimes the Earth’s atural mag etism ca cause the scree to look tilted. a) If o correctio is required, press the B butto . b) If some correctio is required, press the OK butto . Press the V or v
butto to rotate the picture over a ra ge of -5 to +5. Press the OK butto
to store.
A autotu e prompt appears o scree . Press the OK butto to select ‘Yes’. A me u is displayed givi g you two optio s to choose from: Quick tuning: Tu es i the recomme ded sig als for your locatio . Full tuning: Tu es i all the available sig als. Use the V or v butto s to make your choice the press the OK butto .
Note: ‘Full tu i g’ may take some time to tu e i all the available sig als. For ormal use, we recomme d you use the ‘Quick tu i g’ feature. A display appears aski g you to press the OK butto to begi tu i g. As the digital tu i g procedure may take some time, a me u is displayed to show you the tu i g progress. Whe the o scree display i forms you that the tu i g is successfully fi ished, press the BLUE butto repeatedly to remove all me us from the scree .The a alogue tu i g procedure the begi s. If o digital a d o a alogue sig als are fou d, a display appears o scree aski g you to co firm your aerial is co ected. Check your aerial is co ected the press the OK butto to repeat the tu i g procedure.
O ce all sig als have bee captured a d stored, the TV retur s to ormal operatio a d displays the digital programme captured o programme umber 1.
Note: If o digital sig als are captured, the the a alogue programme stored o programme umber 1 is displayed.
3.
To view programmes, press the PROG+/- butto or the umbered butto s o the remote co trol.
Automatically tuning the TV
The operating instructions mentioned here are partial abstracts from the ‘Operating
Instruction Manual’. The page numbers of the ‘Operating Instruction Manual’ remain
as in the manual.
SECTION 1 GENERAL

- 14 -
Digital features
21
DIGITAL
DIGITAL
OK
The EPG menu
The EPG (Electronic Programme Guide) menu provides a quick and easy way to: a) View a complete list of programmes available. b) Obtain a preview of the programmes currently being broadcast. c) Create a list relating to a category of programme, e.g. Sports or Movies. d) Record programmes. To select a category of programme
1.
The EPG menu is only available in digital mode. To check you are in digital mode, press the DIGITAL/ button on the remote control. An information
banner appears briefly on screen when you change channels. If the banner does not appear, press the DIGITAL/ button.
2.
Press the button to display the EPG menu on screen. This menu consists of an event information box, a preview screen, a 2 hour timer bar (divided into 30 minute intervals) and a 5 channel programme list covering the 2 hour period.
3.
Press the V, v, Band bbuttonsto move around the list. As each programme is highlighted, a brief description of the programme appears in the event box at the top left of the menu. Ifyou press the bbutton after highlighting the last programme on the right, the programme schedule for the next 2 hour period is displayed. Press the RED or GREEN button when you wish to view the
previous or next 5 channels and their programmes.
4.
If a programme you highlight is currently being broadcast, you will be prompted to press the OK button to obtain a preview. If however, you have previously allocated a Parental Control age limit in the Main Menu, and the programme exceeds that limit, you will be asked to enter your PIN before the preview is allowed.
5.
Press the OK button to confirm your choice and exit the EPG menu
1.
With the EPG menu on screen, press the BLUE button to display the ‘Category’pop-up menu.
2.
Press the Vor vbuttons to highlight the category you want, then press the
OK button. The EPG programme list will now onlycontain programmes of the type selected. Some examples of category types are as follows: Choice This isa list compiled from the programmes you view most
often.
Recent Prog. This list contains the last 5 channels you have watched. Fav1 This list contains channels you have stored in this folder
as favourites.
Movies This list contains all the movies available for viewing. All Programmes This is a complete list of all available programmes.
3.
Your chosen category is displayed at the top of the list along with the date and time of day.
4.
Press the button to exit the EPG menu.
Basic operation
11
1
4
7
3
6
9
2
5
8
8
0
DIGITAL
DIGITAL
OK
PROG
Viewing traditional teletext
Most analogue TV channels broadcast a text service. The index page (usually page 100) provides information on how to use the service. Please ensure you are receiving a strong signal or some text errors may occur. Switching on the text service How to use the text features
1
Select the TV channel that carries the text service you wish to view.
2
Press the button to enter Picture and Text (P&T) mode. The screen is divided into two with the Text display on the left and the TV channel in the right corner. Press the button a second time to enter full screen Text mode. Press the button a third time to enter Mix mode.
3
Press the numbered buttons to enter a three digit number for the text page you wish to view. Your selected page appears on screen.
4
Enter more 3 digit page numbers as required.
5
When you have finished viewing the text service, press the DIGITAL/ button to remove the text display from the screen.
Text Features How to select To select the next or preceding page Press the or button. To select a sub page A text page can consist of several sub pages. In this case
an information box is displayed at the bottom of the screen showing the number of sub pages available. Select the sub pages by pressing the Vor vbutton.
To keep a page on display Press the button. Press again to cancel. To use Fastext Fastext allows you to access pages with one button push.
When Fastext is available, four coloured items appear at the bottom of the screen. Press the corresponding coloured button on the remote control to display the page.
To use the Page Catching feature Select a page that contains several page numbers (e.g.
the index page), then press the OK button. Press the Vor vbutton to highlight the page number required, then press the OK button again. Your selected page appears on screen.

- 15 -
TV menu system 26
OK
Manual Set Up menu This menu gives you access to more advanced features. The options are: Language/Country When you first installed the TV you were asked to select your language and country. The ‘Language/Country’option in the ‘Manual Set Up’menu allows you to change these settings. With the ‘Language/Country’option highlighted, press bto enter the
‘Language/Country’menu. Press v or V to select ‘Language’or ‘Country’. Press bto
select. Press v or V to highlight the required setting. Press OK to confirm.
Manual Programme Preset With the ‘Manual Programme Preset’option highlighted, press bto enter the ‘Manual
Programme Preset’menu. The ‘Manual Programme Preset’menu is explained on the
following page. Further Programme Preset With the ‘Further Programme Preset’option highlighted, press bto enter the ‘Further
Programme Preset’menu. The ‘Further Programme Preset’menu is explained on page
28. RGB Set Up When viewing signals from RGB equipment connected to the AV1 or AV2 sockets (e.g. DVD player, PlayStation) the picture may need adjusting. The ‘RGB Set Up’option in the ‘Manual Set Up’menu allows you to adjust the size and horizontal picture position of signals from RGB equipment. With the ‘RGB Set Up’option highlighted, press bto
enter the ‘RGB Set Up’menu. Press bto select H Centre. Press v or V to centralise the
picture over a range of -10 to +10. Press OK to store. Press v to select H Size. Press v
or V to adjust the picture size over a range of -10 to +10. Press OK to store.
Note: If there is no RGB equipment connected to either the AV1 or AV2 scart sockets the ‘RGB Set Up’ option will not be available. Picture Rotation Due to the Earth’s natural magnetism the picture might slant slightly. The ‘Picture
Rotation’option in the ‘Manual Set Up’menu allows you to cancel out this effect. With the ‘Picture Rotation’option highlighted, press bto select. Press v or V to rotate the picture over a range of -5 to +5. Press OK to store. Personal ID The ‘Personal ID’option in the ‘Manual Set Up’menu allows you to enter a code which
could help to trace you should the TV be stolen and recovered. This code can only be entered once - please make a note of it and keep it safe. With the ‘Personal ID’option
highlighted, press bto select. Press v or V to display the first character of the code you wish to use. Press bto select. Repeat until all characters have been entered. Press OK to store. A confirmation screen is displayed. Press OK to confirm.
TV menu system
23
OK
MENU
OK
The following pagesexplain the TV set up menus and their operation. Although most of these menus can be accessed when watching digital programmes, we recommend you view them in analogue mode. To check which mode you are in, press the button on the remote control. If you are watching a digital programme, an Info display appears on screen providing brief details for the current and next programme. If this happens, press the DIGITAL/ button on the remote control to switch to analogue channels.
This TV contains a menu system which is based on a series of on screen displays. These displays help you get the most from your TV, from customising the picture and sound to accessing advanced features. Use the following buttons on the remote control to operate the TV menu system. Picture Adjustment menu This menu allows you to customise the picture. Highlight the required option and press bto select. The table below explains each option and how to use it.
1.
Press the MENU button to display the main menu.
2.
Use the following buttons to operate the menu: - Press the v or V buttons to highlight the required menu or option. - Press the b button to enter the required menu or option. - Press the B button to return to the last menu or option. - Press the v, V, Bor bbuttons to alter the settings of the selected option.
- Press the OK button to confirm and store your selection.
3.
Press the MENU button to remove the menu from the TV screen.
Option How to use
Picture Mode This option allows you to select one of four picture modes. Live, Movie and Game modes are preset and only Contrast can be adjusted. The Personal mode, however, also allows you to adjust the Brightness, Colour and Sharpness options.
Press Vor vto select Live,
Personal, Movie or Game. Press OK to confirm.
Contrast, Brightness, Colour, Sharpness These options allow you to adjust the contrast, brightness, colour and sharpness. Note: Brightness, Colour and Sharpness can only be
adjusted when Picture Mode is set to Personal.
Press Bor bto set the levels. Press OK to
confirm.
Reset This option resets all picture settings to the factory preset levels. Press bto restore default
picture settings.
AI (Artificial Intelligence) This option monitors the picture and limits any sudden increases in Brightness and Contrast. Press Vor vto select On or
Off. Press OK to confirm.
Noise Reduction Sometimes a weak signal can produce a snowy picture (called Picture Noise). This option can help to reduce this effect. Press Vor vto select High,
Mid, Low, Auto or Off. Press OK to confirm.
DRC Mode DRC (Digital Reality Creation) Mode allows you to enjoy higher quality pictures. The settings available are: Off: Basic 100Hz picture quality. DRC 50: Improved picture resolution. DRC 100:Optimum picture resolution
Press Vor vto select Off,
DRC 50 or DRC 100. Press OK to confirm.
Colour Tone This option allows you to alter the tint of the picture. The settings available are: Warm: Gives the white colours a red tint. Normal: Gives the white colours a neutral tint. Cool: Gives the white colours a blue tint.
Press Vor vto select
Warm, Normal or Cool. Press OK to confirm.
Using the TV menu system

- 16 -
Memory Stick operation 30
Memory Stick Index
Page +
Page 1/3
OK
DIGITAL
DIGITAL
MEMORY
STICK
DIGITAL
DIGITAL
MEMORY
STICK
OK
Index This feature enables you to view on screen the JPEG DCF format pictures from your memory stick. Slideshow This feature allows you to display all the memory stick pictures as a slideshow presentation on the TV screen.
1.
Press the MEMORY STICK button on the remote control to display the ‘Memory Stick’menu on the TV screen.
2.
Press the Vor vbutton to highlight ‘Index’then press the OK button to display the ‘Memory Stick Index’screen.
3.
Press the v, V, Bor bbuttons to highlight the required picture, then press the
OK button to display the picture fully on the TV screen.
Note: Only a limited number of pictures can be displayed on the Index screen at one time. If your required picture is not visible, highlight
‘Page +’
then press the OK button to
view the next set of pictures. Press the v, V, Bor bbuttons to select your desired
picture then press the OK button to view.
4. Use the v, V, Bor bbuttons to highlight ‘Back’. Press the OK button to return
to the ‘Memory Stick’menu or press the DIGITAL/ button at any time to
return to normal TV operation.
1. Press the MEMORY STICK button on your remote control to display the
‘Memory Stick’menu on the TV screen.
2. Press the Vor vbutton to highlight Slideshow. 3. Press the OK button to start the slideshow. (To change the length of time an
image is displayed refer to the ‘Setup’section on the following page.)
4. Press the OK button during the slideshow to return to the ‘Memory Stick’
menu. Press the DIGITAL/ button to return to normal TV operation.
Memory Stick operation
29
MEMORY
STICK
Viewing Memory Stick pictures
A ‘Memory Stick’* is a new recording medium with a data capacity that exceeds a floppy disk. It is specially designed for exchanging and sharing digital data among ‘Memory
Stick’compatible products. Use ‘Memory Stick’to display JPEG pictures (DCF version
1.0 format)** individually or as a slideshow presentation on the TV screen. Because it is removable, ‘Memory Stick’can also be used for external data storage. Inserting a ‘Memory Stick’ Insert a memory stick into the front control panel of the TV set until it clicks into the connector. The vsymbol must be facing forwards. The red light flashes indicating that
the memory stick contents are being read.
Removing a ‘Memory Stick’ Confirm that the red light is off. Do not pull the memory stick. You must push the memory stick and then release. The memory stick will spring out. Note: *Data stored on a ‘Memory Stick’may become damaged or erased if you remove the ‘Memory Stick’when it is reading or writing data. The ‘Memory Stick’ menu The ‘Memory Stick’menu is displayed automatically when you insert the memory stick into your TV set. Alternatively, if there is a memory stick already inserted, press the MEMORY STICK button on the remote control to display the menu screen. There are 3 options available, namely ‘Index’, ‘Slideshow’and ‘Setup’. Notes: Memory Stick’and the logo are trademarks of Sony Corporation.
DCF (Design rules for Camera File systems) is a standard file name format for digital
still cameras, DV camcorders etc. It is supported by SONY and other manufacturers.

- 17 -
Sony Corporation Printed in Spain Ecological Paper - Totally Chlorine Free
= KD-32NX200
= KD-36NX200
Connecting other equipment 36
1
4
7
3
6
9
2
5
8
0
MODE
Using the remote control with VCR and DVD players This remote control has been configured to operate not only Sony DVDs and VCRs but also those made by other manufacturers. To operate other makes of DVD and VCR using this remote control, complete the following procedure:
1.
Find the 3 digit code for your brand from the list below. If your brand has more than one code allocated to it, make a note of the first code only at this stage.
2.
Press the MODE button on the remote control until either the VCR green light or the DVD green light illuminates.
3.
With the required green light illuminated, press and hold down the YELLOW button for
approximately 6 seconds, until the light starts to flash.
4.
Using the numbered buttons, enter the 3 digit code for your DVD or VCR. Once a correct
number has been entered, all three green lights will illuminate momentarily.
5.
Turn on your DVD or VCR and check that the remote control operates the main functions. If not, repeat steps 2 - 4 and enter the next 3 digit code allocated to your brand of VCR or DVD.
6.
When you wish to use the remote control to operate the TV again, press the MODE button until the TV green light illuminates. Don’t forget to select VCR or DVD using the MODE button every time you wish to operate that equipment with this remote control.
Note: The brand codes you set may be lost if weak batteries are not replaced immediately. Should this happen, use the above procedure to reset the code. A small label has been attached to the inside of the battery cover for you to make a note of your brand codes. Not all brands and models of DVDs or VCRs are covered in this list. However, Sony will endeavour to update the software periodically, so please refer to the code table provided with your remote control. VCR Brand List DVD Brand List
Brand Code Brand Code SONY (VHS) 301, 302, 303, 309 SONY 001 SONY (BETA) 301, 302, 303, 309 AIWA 021 SONY (DVD) 304, 305, 306 DENON 018, 027, 020, 002 AIWA 325, 331, 351 GRUNDIG 009, 028, 023, 024, 016. 003 AKAI 326, 329, 330 HITACHI 025, 026, 015, 004 DAEWOO 342, 343 JVC 006, 017 GRUNDIG 358, 355, 360, 361, 320, 351 KENWOOD 008 HITACHI 327, 333, 334 LG 015, 014 JVC 314, 315, 322, 344, 352, 353, LOEWE 009, 028, 023, 024, 016. 003 LG 332, 338 MATSUI 013, 016 LOEWE 358, 355, 360, 361, 320, 351 ONKYO 022 MATSUI 356, 357 PANASONIC 018, 027, 020, 002 ORION 328 PHILIPS 009, 028, 023, 024, 016. 003 PANASONIC 321, 323 PIONEER 004 PHILIPS 311, 312, 313, 316, 317, 318, SAMSUNG 011, 014 SAMSUNG 339, 340, 341, 345 SANYO 007 SANYO 335, 336 SHARP 019, 027 SHARP 324 THOMSON 012 THOMSON 319, 350 TOSHIBA 003 TOSHIBA 337 YAMAHA 018, 027, 020, 002

- 18 -
Additional Information 38 Troubleshooting Here are some simple solutions to problems which may affect the picture and sound. •If you continue to have these problems, have your TV serviced by qualified personnel or you can contact the Sony
Customer Information Line on 0870 599 1999.
•NEVER open the casing yourself.
Problem Possible causes Solutions No picture, no sound. •Power off
•TV in standby. •Aerial disconnected.
•Plug in the TV. •Press the
button on the front of the TV.
If the
indicator is on press the button on the remote control.
•Check aerial connection
Poor or no picture (screen is dark), but good sound. •Picture preset level adjustment •Select ‘Picture Adjustment’menu then adjust adjust the
brightness, picture and colour levels.
No picture on any channel after digital tuning. •No digital transmissions in your area.
•No digital transmissions from the
transmitter you are currently using.
•Unsuitable aerial. •Weak signal.
•Tune in all the Analogue channels available using the
‘Manually tuning analogue signals’instructions of this manual to tune in available analogue channels, then contact local installer to find out when digital transmissions begin in your area.
•Contact a local installer to find out at which transmitter you
should be pointing your aerial.
•Change your aerial to cover the channels used by digital
programmes.
•Ensure aerial is correctly aligned to transmitter. •Ensure aerial is is plugged directly into the TV (not through
other equipment).
•Upgrade to a higher gain aerial.
Some channels are blank. •Scrambled or subscription-only
channel.
•Programme used only for data (no
picture or sound).
•Programme not being transmitted.
•Subscribe to pay-per-view broadcaster. •See ‘Skipping a programme’section. •See ‘Re-arranging your channels’section.
Standby indicator flashing. •Fault (irregular flash)
•Digital mode Timer Record active
(regular flash).
•Do not open the cabinet, refer to qualified personnel. •Contact your nearest SONY Service Centre. •Will clear when Timer Recording stops.
Good picture, no sound •Volume control. •Press the + button on the remote control.
•If is displayed on the screen, press the button on
the remote control.
Poor picture quality •Wrong external mode selected for an
RGB video source. •Press the button repeatedly until the RGB symbol
is displayed on screen.
No colour on colour programmes •Colour level setting. •Select ‘Picture Adjustment’menu then adjust the colour
setting.
Remote control does not function •Batteries low. •Replace batteries. Distorted picture when changing programmes or selecting teletext
•Inputs from external equipment not
switched off. •Switch off all additionally connected equipment.
/
Additional Information
37
Specifications
TV System B/G/H, DK, DVB-T Colour System PAL,SECAM
NTSC 3.58, 4.43 (only Video In) MPEG-2 MP@ML
Channel Coverage See the ‘Channel Display Table’below Picture Tube KV-32NX200E FD Trinitron Approx. 82cm
KV-36NX200E FD Trinitron Approx. 91cm
Sound Output Left/Right: 2x20W (music power), 2x10W (RMS)
Subwoofer: 1x30W (music power), 1x15W (RMS)
Power Consumption KV-32NX200E 154W (1w standby)
KV-36NX200E 182W (1w standby)
Dimensions (w x h x d) KV-32NX200E Approx. 910 x 445.5 x 590mm
KV-36NX200E Approx. 1010 x 645 x 607mm
Weight KV-32NX200E Approx. 67kg
KV-36NX200E Approx. 87kg
Rear Terminals 21-pin Euro connector (CENELEC standard) including audio/video
input, RGB input, TV audio/video output.
21-pin Euro connector (CENELEC standard) including audio/video input, RGB input, TV audio/video output 21-pin Euro connector (CENELEC standard) including audio/video input, S-video input, selectable audio/video output.
Conditional Access Module RF In Audio output - RCA phono jacks
Front Terminals Video input - phono jack
S video input - 4 pin DIN Audio inputs - phono jacks Headphones jack - minijack stereo
Accessories Supplied RM-939 remote control (1)
IEC designated size AAA (R03) battery (2) RF Loopthrough cable (1)
Modem (1)
1
2
3/
s
3
4
s
4
4
Design and specification are subject to change without notice
Channel Display Table
Receivable Channels Channel Displays
B/G/H E2.12, 21...69 C02.C12, C21...C69 KABEL-TV (1) S1..S41 S01...S41 KABEL-TV (2) S01..S05 S42...S46
M1...M10 S01...S10 U1...U10 S11...S20
ITALIEN A, B.H, H1, H2 C13, C14.C20, C11, C12 D/K R01.R12, R21.R69 C01...C12, C21...C69
S01...S05 S42...S46

- 19 -
SECTION 2 DISASSEMBLY
2-1. Rear Cover Removal
To remove lift the main bracket rear slightly and slide the
chassis away from the beznet. Ensure that the interconnecting
leads are released from their purse locks to prevent damage
being caused.
When refitting the chassis ensure that the main bracket is
located in the beznet guide slots before sliding the chassis
forwards. Refit the inter-connecting leads in their respective
purse locks.
2-3. Chassis Removal and Refitting
2-2. Speaker Box Removal
Remove the rear cover fixing screws indicated and pull the
rear cover backwards away from the set.
=>
Screws
To remove the speaker box assembly remove the two screws
circled and unplug the speaker lead from connector CN1202
on the ‘A’ board. The assembly can then be lifted gently
away from its supporting arms.
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>
=>

- 20 -
2-5. G Board Removal
2-6. D2 Board Removal
To remove the D2 board remove the two screws circled,
release the clips circled and ease the board gently away from
the support bracket.
Screws
Clips
2-7. D1 Board Removal
To remove the D1 board first remove the D2 bracket by
removing the two screws (one on each side of the bracket)
and releasing the four clips (two on each side of the bracket).
The D1 board can then be removed using the same method as
the G board.
Screw
Clips
To remove the G Board first remove the G1 bracket by
removing the screw circled and releasing the four clips (two
on each side of the bracket).
The G Board can then be removed by releasing the clips circled
and easing the board gently away from the support bracket.
Clips
2-4. G1 Board Removal
To remove the G1 board release the three clips circled and
ease the board gently away from the support bracket.
Clips
Clips
Screw