Sony HSR-X200 User manual

DIGITAL SURVEILLANCE RECORDER
HSR-X200
HSR-X200P
SERVICE MANUAL
Volume 2 1st Edition (Revised 1)

HSR-X200/X200P
2
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

HSR-X200/X200P 3
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichenTyp. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandépar le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning måkun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitäkäytetty paristo valmistajan ohjeiden
mukaisesti.

HSR-X200/X200P
4
For the customers in the Netherlands
Voor de klanten in Nederland
Dit apparaat bevat een (CF)n-Li batterij voor memory
back-up.
Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat bij einde
levensduur afdankt.
Gooi de batterij niet weg. maar lever hem in als KCA.
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the rear of
the unit 5 cm (2 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.

1
HSR-X200/X200P
/ Table of Contents
............................................................................................................ 3 (J)
..................................................................................................... 3 (J)
....................................................................................................................... 3 (J)
........................................................................................................ 3 (J)
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
Contents ............................................................................................................... 3 (E)
Trademark............................................................................................................ 3 (E)
4. Semiconductor Pin Assignments
5. Spare Parts
5-1. ........................................................................................5-1
5-1. Notes on Repair Parts..................................................................................5-1
5-2. Exploded Views ..........................................................................................5-2
5-3. Electrical Parts List .....................................................................................5-6
5-4. Packing Materials and Accessories ...........................................................5-23
6. Block Diagrams
6-1. ................................................................................................ 6-1 (J)
6-1. Circuit Description ................................................................................6-1 (E)
6-2. Overall.........................................................................................................6-5
CD-1............................................................................................................6-6

2HSR-X200/X200P
7. Board Layouts
CD-1 ............................................................................................................7-2
PC-1.............................................................................................................7-4
OP-1 ............................................................................................................7-4
OP-2 ............................................................................................................7-4
TB-1 ............................................................................................................7-5
TB-2 ............................................................................................................7-5
TB-3 ............................................................................................................7-5
TB-4 ............................................................................................................7-5
PW-1 ...........................................................................................................7-6
8. Schematic Diagrams
CD-1 (DM-A)..............................................................................................8-3
CD-1 (DM-B) ..............................................................................................8-9
CD-1 (DM-C) ............................................................................................8-15
OP-1 ..........................................................................................................8-18
OP-2 ..........................................................................................................8-19
TB-2 ..........................................................................................................8-19
TB-3 ..........................................................................................................8-19
TB-4 ..........................................................................................................8-19
TB-1 ..........................................................................................................8-20
PW-1 .........................................................................................................8-21
PC-1...........................................................................................................8-22

3 (J)
HSR-X200/X200P

3 (E)
HSR-X200/X200P
Manual Structure
Purpose of this manual This manual is the Service manual volume 2 of Digital Surveillance recorder HSR-
X200/X200P.
This manual describes semiconductor pin assignments, detailed parts list, block
diagrams, board layouts, and schematic diagrams.
Related manuals In addition to this Service Manual Volume 2, the following manuals are provided.
..
..
.Operating Instructions
HSR-X200/X200P (Supplied with equipment)
Parts number : 3-206-603-1X (UC)
3-206-603-2X (CE)
..
..
.Service Manual Vol. 1 (Available on request)
Part number : 9-955-344-1X
Contains the maintenance information of this equipment, and servicing informa-
tion necessary for parts replacement and adjustments.
Contents The sections covered in the manual are summarized below to give you a general
understanding of the manual.
Section 4 Semiconductor Pin Assignments
Describes information on semiconductors used for unit.
Section 5 Spare Parts
Describes the exploded views, the mechanical parts list, and the electrical parts list.
Section 6 Block Diagrams
Describes the circuit description and the block diagrams of overall.
Section 7 Board Layouts
Describes the board layouts for the unit.
Section 8 Schematic Diagrams
Describes the schematic diagrams for the unit.
Trademark Trademarks and registered trademarks used in this manual are follows.
.Windows is a registered trademark of Microsoft Corporation.