Sorelle 1050 User manual

Made in China
Important Information:
Before assembly, readthese instructions. Make sure
all preassembled parts are tight. Store this instruction
manual in envelope (attached to mattress support
tube) for future reference.
By Sorelle - A Division of C&T International, Inc.
46 Whelan Road East Rutherford N J. 07073 U S A
Tel, [phone]Fax,[phone]
Sorelle
1050
CRIB AND MORE

2
WARNING -
• Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. DO NOT
USE THIS CRIB IF THE INSTRUCTIONS CANNOT BE STRICTLY FOLLOWED.
• Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use crib is any parts are missing or broken. Ask your dealer or write to C&T
Internatinoal/Sorelle for replacement parts and instructional literature if needed. DO NOT substitute
parts.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
• When child is able to climb out or reaches the height of 35 in. (90 cm), the crib shall no longer be
used and can be converted to the transitional bed.
• DO NOT place crib near window where cords from blinds or drapes may strangle a child. Child may
fall out of window. DO NOT place cords, straps or similar items that could become wound around
the child’s neck in or near the crib.
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
• If refinishing, use a non-toxic finish specified for children’s products.
• The product including side rails must be erected prior to use.
• Always provide the supervision necessary for the continued safety of your child. When used for
playing, never leave child unattended.
• To help prevent stangulation tighten all fasteners .
• A child can trap parts of the body or clothing on loose fasteners .
• When child is able to pull to a standing position, set matter to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.”
• Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
• DO NOT use a water mattress with this crib.
• Ensure a safe environment for your child by checking regularly, (that every component is properly
and securely in place) before placing your child in the crib. Make sure that all bolts and fasteners
are tight.
CRIB WARNINGS
Failure to follow these warnings and assembly instructions
could result in serious injury or death.
!
WARNING - Infants can suffocate in gaps between a mattress too small or too
thick and product sides. On soft bedding, NEVER add a mattress,
pillow, comforter, or padding.
!
WARNING
STRANGULATION HAZARD
FALL HAZARD
CAUTION : ANY MATTRESS USED IN THIS CRIB MUST
BE AT LEAST 24” (61CM) x 38” (96.5CM) WITH A
THICKNESS NOT EXCEEDING 6” (15CM).

3
CLEANING & MAINTENANCE
• ALWAYS STORE THE CRIB & CHANGING TABLE IN A CLEAN AND DRY PLACE.
• TO CLEAN YOUR CRIB & CHANGING TABLE, USE A SOFT DAMP CLOTH WITH A SMALL
AMOUNT OF MILD SOAP, WIPE IMMEDIATELY WITH A DRY CLOTH.
• DO NOT USE ABRASIVES OR DETERGENT ON CRIB & CHANGING TABLE SURFACES.
• REGULARLY CHECK ALL SCREWS AND FITTINGS TO ENSURE THEY ARE TIGHT.
• THE IDEAL BALANCE IS TO MAINTAIN THE TEMPERATURE AROUND 21°C (70°F) AND THE
RELATIVE HUMIDITY AT 40% TO PREVENT WARPING OR SPLITTING.
• FALL HAZARD—to prevent death or serious injury, always keep child within arm’s reach. Never leave
child unattended.
• Read all instructions before use of the changing table. Keep instructions for future use.
• Check all screws and bolts and make sure they are tight before using. From time to time check over
your Changing Table. You should never use it if parts are missing or broken,
• Use only the pad provided by the manufacturer.
• DO NOT use the changing table if it is damaged or broken.
• Maximum weight of child: 25 lbs. (11.4 kg)
• Always secure the pad provided to the changing surface by inserting the safety belt through the slot
in the changing pad. Always use the restraining strap provided
Failure to follow these warnings and assembly instructions
could result in serious injury or death.
WARNING -
CHANGING TABLE WARNINGS
!

4
PARTS LIST
Crib Assembly
Parts List
(A1) Left Side Rail (x1) (C1) Front Side Rail (x1)
(B1) Back Side Rail (x1)
(D1) (x14)
(E1) Front & Back Contoured Top (x2)
(F1) Rear Leg (x1) (G1) Front Leg (x1)
(H1) (x2)
(I1) (x2)
Mattress Support Assembly Parts
(Q) Bolt with Loctite®
Threadlocker Blue (x4)
(X1) Dowel Pin (x4)
Allen Wrench
Allen Wrench

5
PARTS LIST
Dresser Assembly
Parts List
M
rzer T
r
J
rt
rack
t
r z M
Fr
r
v
L
ec ra v r
r
r
r v
r
r r
r r
T r v
r r
r v
W r
2
(C-1)Suppo
(C-2)Suppo
(C-3)Suppo
(C-4)La
(C-5)La
(C-6)La
(C-7)D

6
PARTS LIST
Additional Assemblies
Parts List
(L) Rear Dresser Leg (x1)
(M) Front Foot Board Leg (x1)
Screwdriver
(A2) Drawer Bottom (x3)
(B2) Drawer Back (x3)
(C2) Drawer Left (x3)
(D2) Drawer Right (x3)
(E2) Knob (x3)
(F2) Drawer Front (x3)
(G2)
Phillips Screw
Long (x24)
(B2)
(A2)
(C2)
(D2) (I2)
(H2)
Screw for
Knob (x3)
Screws shown at actual size.
(E2)
Full Size Headboard Parts
(F2)

7
ASSEMBLY
Drawer Assembly
(H2)(x3) (G2)(x24)
1
2
3
4
Grooves
1.Working on a padded
flat surface, attach Drawer
Sides (C2 &D2) to Drawer
Back (B2) with Philips Head
Screw. Figure 1.
2. Slide Drawer
Bottom (A2) into drawer
assembly. Figure 2.
3. Secure both sides of
Drawer Front (F2) to drawer
assembly with four (4)
Screws (G2).Figure 3.
Check all screws for
tightness.
4. Using Drawer Knob
Screw (H2), install one (1)
Knob (E2) on Drawer.
Figure 4.
Repeat for all drawers.
Set drawers aside for
later use.
(D2)
(B2)
(A2)
Parts Needed: Refer to pg. 6,“Drawer Parts”
(C2)
(E2)
(F2)
(G2)
(G2)
(G2)
(G2)
(H2)
(E2)(x3)

8
ASSEMBLY
(A)
(C-3)
1. Insert Wooden Notch of Support Bar (C-3) into
opening on front side of Middle Panel (A) and
secure with Bolt (F). Figure 1.
1
Parts Needed: Refer to pg. 5,“Dresser Parts”
(F)
2. Insert two (2) wooden pegs on Support Bar
(C-5) into openings on Middle Panel (A).Figure 2.
NOTE: Grooves face towards back of unit.
(A)
(C-5)
2
(A)
3. Insert wooden notch on Rear Support Bar (C-6)
into openings on Middle Panel (A) and secure
with Bolt (F). Figure 3.
3
(C-6)
(F)
(F) (x4)
(A)
4. Insert wooden notch on Decorative
Support Bar (C-7) into openings on Middle Panel
(A) and secure top and bottom of bar using two
(2) Bolts (F). Figure 4.
4
(C-7)
(F)
(F)

9
ASSEMBLY
5. Insert wooden peg on Small Front Support Bar
(H) into opening and (C-4) on Middle Side Panel
(A) and secure with Bolt (F). Figure 5.
5
(F)
(H)
(A)
8. Insert Support Bar Solid Ends (C-1) and attach
Right End (B) with each support bar on Left Side
Rail (A). Figure 8.
8
(B)
(A)
(C-1)
7. Insert Bottom Shelf (I) into grooves on middle
and back bottom braces. Figure 7.
7
(I)
(F) (x2)
6. Lay Middle Panel (A) on its side. Insert
Front Support Bar w/groove (C-2) into notch
on Middle Panel (A) and slide Dresser Top (E)
into top grooves. Slide Organizer Middle (D)
into grooves. Figure 6.
6
(E)
(D)
(A)
(C-3)
(C-2)
(F)
(C-4)

10
ASSEMBLY
9. Secure Right End (B) with six(6) Bolts (F) to
supoort bars. Figure 9.
9
(B)
(F)
(F) (x6)
(F)
(F)
(F)
(F)
(F)

11
ASSEMBLY
(H1) (x2)
(D1) (x4)
(I1) (x2)
3. Attach Back Side Rail (B1) to Left Side Rail
(A1) with two (2) Bolts (D1). Figure 3.
(D1)
(B1)
(A1)
3
(D1)
1. Using two (2) Bolts (H1) and two (2) Bolts
(I1), assemble Front Leg (G1) and Rear Leg (F1)
to Left Side Rail (A1). Make sure all mattress
support holes are facing in. Figure 1.
(F1)
(G1)
(H1)
1
(H1)
(A1)
Crib Assembly
4. Attach Back Side Rail (B1) to Changing Table
with two (2) Bolts (D1). Figure 4.
(D1)
(D1)
4
2
2. Dowel Pin Assembly
Slide one (1) Dowel Pin (X1) into each end of
Back Side Rail (B1) (total of 2).Figure 2.
(B1)
(X1)
(B1)
(X1) (x2)
(I1)
(I1)
(X1)

12
ASSEMBLY
(D1)
8. Attach Front Side Rail (C1) by threading two
(2) Bolts (D1) through Left Side Rail (A1) and two
(2) Bolts (D1) through inner right side of chang-
ing table. Figure 8.
NOTE: Bottom right side of Front Side Rail
(C1) must be bolted into top hole at bottom of
changing table.
(C1)
8
(D1)
(D1)
(D1)
6
Attaching Mattress Support
5. Attach completed Mattress Support Assem-
bly to crib using four (4) Bolts with Loctite®
Threadlocker Blue (Q). Figure 5 & Figure 6.
NOTE: For infants, set mattress support
assembly in an upper position for greater
accessibility. As child grows and can stand,
mattress support assembly must be lowered.
See Warning Statements.
5
(D1) (x4)
(Q) Bolt with
Loctite® Thread-
locker Blue (x4)
7. Dowel Pin Assembly
Slide one (1) Dowel Pin (X1) into each end of
Front Side Rail (C1) (total of 2). Figure 7.
(C1)
(X1)
(X1)
7
(A1)
(X1) (x2)
(Q) (Q)
(Q) (Q)

13
ASSEMBLY
12. Insert Shelf Support Brackets (K) into holes in
back of organizer. Slide shelves (J) into “bite”of
bracket. When in place, tighten retainer screws
on brackets. Figure 12.
NOTE: Retainer screws MUST be tightened to
keep shelves from moving.
Add changing pad to top of organizer.
(J)
(K)
Bite
Retainer Screws
(D1) (x6)
11. Secure Back Contoured Top (E1) to top of
Back Side Rail (C1) with two (2) Bolts (D1) and
one (1) Bolt (D1). Figure 11.
Once complete, insert three (3) drawers into
changing table.
(C- 4)
9. Insert groove on bottom of Front
Contoured Top (E1) to top of Front Side Rail
(C1). Figure 9.
NOTE: Loosen bolts on Left Side Rail (A1) to fit
Front Contoured Top (E1). Retighten once in
place.
(E1)
9
(C1)
(A1)
10. Secure Front Contoured Top (E1) to top of
Front Side Rail (C1) with two (2) Bolts (D1) and one
(1) Bolt (D1).Figure 10.
(E1)
(D1)
(D1)
(C1)
10
(D1)
11 12
(D1)
(D1)
(D1)
(K) (x8)

14
ASSEMBLY
Changing Pad Assembly
3. Make sure that safety belt is fastened around
child, and adjusted so safety belt is snug around
child’s mid-section. Make sure buckle is securely
latched. Figure 3.
CLICK!
1
2
3
2. Pull through front of pad completely. Make
sure pad is facing up and warnings are always
visible. Figure 2.
Important : If changing pad and safety belt are
assembled, make sure warnings are facing up and visible.
If not, reassemble by following the steps below.
1. Locate safety belt bolted to dresser top. Insert
safety belt through slit in changing pad from
back of pad. Figure 1.
Disassembling Crib For Storage
To disassemble crib for storage, follow assembly steps in reverse.
Store all parts and hardware together in a safe place. Store the instruction manual in the supplied
envelope attached to the mattress support assembly for future reference for reassembly.
For models using casters, set casters to LOCKED position.

15
ASSEMBLY
Converting to a Toddler Bed .
Toddler Rail(OPTIONAL PURCHASE)
Assembly the Toddler Rail please refer to the instruction of Toddler rail.
Converting to a Full Size Headboard
Remove bolts from front and back to remove
organizer. Figures 1 & 1a.
1
Remove mattress support assembly and
drawers from crib.
1a
NOTE: REMOVE FRONT BOTTOM SUPPORT BAR
IN ORDER TO ACCESS BOLT TO REMOVE BOTTOM
OF FRONT RAIL. Figure 1a.
Remove Bottom Support Bar,
then replace after rail bolt is
removed.
IMPORTANT: You MUST use supplied Wall Strap Kit with stand-alone organizer. See instructions
provided with Wall Strap Kit.

16
3
Attach rear leg that was removed from
organizer and attach to headboard using
bolts removed from organizer as shown in
Figure 3.
To use extra Front Leg (M) to convert to full
size bed with footboard and headboard,
refer to Adult rails 215# instruction.
After removing crib from organizer, remove
Left Ride Rail. To do so, remove four (4) Bolts.
Figure 4.
4
2
Remove larger rear leg from organizer and replace
with Rear Dresser Leg (L) as shown in Figure 2.
NOTE: REAR ORGANIZER LEG (L) WILL BE SAME
SIZE AS OPPOSITE REAR LEG ON ORGANIZER.
(L)
Adult rails 215# & Toddler rail can be purchased to covert the crib to
a full size bed and a toddler bed.
Contact the store where you purchased the crib or visit
www.sorellefurniture.com to locate a dealer near you.