Sound Skulptor MP573 User manual

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
MP57 Assembly guide
MP57 Assembly guideMP57 Assembly guide
MP57 Assembly guide
Safety warning
Safety warningSafety warning
Safety warning
The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the
realisation of a kit unless he has full knowledge about safely handling main powered devices.
Please read the “DIY guide” before beginning.
Print or open the following documents :
•MP57 Schematics
•MP57 Components layout
•MP57 Parts list
•MP57 Setup guide
Follow this guide from item number 1 till the end, in this order. The assembly order is based on components height, from
low to high profile, in order to ease the soldering process : The component you are soldering is always taller than the
previously assembled ones and it is pressing nicely against the work area foam.
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
MP57 Assembly guide
MP57 Assembly guideMP57 Assembly guide
MP57 Assembly guide
25.
25.25.
25. Input transformer – SK5468 Version 1.2
Input transformer – SK5468 Version 1.2Input transformer – SK5468 Version 1.2
Input transformer – SK5468 Version 1.2
Check the version number of the SK5468 PCB. If it is version 1.2,
Insert the 90° 1 pin headers into the SK5468 PCB. It must be
inserted from the solder side (the side without white text), long tail
into the hole. Solder one pin, adjust the position then solder the
other pins. Cut flush. Do the same for both
SK5468's.
Warning
WarningWarning
Warning : the pin headers must sit perfectly perpendicular
to the PCB surface for a good matching with the main
PCB.
Remove the 2 screws from the transformer pin side and
place 2 nylon washers on the holes.
Insert one SK5468 PCB on top of the transformer, white
text down, checking the pin number correspondence.
Assemble with the 2 screws. Solder the transformer pins.
Place the second SK5468 PCB on the other side of
the transformer, white text up. Assemble with the last
2 provided screws.
Insert the transformer into the main PCB and solder
the pins.
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
MP57 Assembly guide
MP57 Assembly guideMP57 Assembly guide
MP57 Assembly guide
26.
26.26.
26. Input transformer – SK5468 Version 1.
Input transformer – SK5468 Version 1.Input transformer – SK5468 Version 1.
Input transformer – SK5468 Version 1.
Check the version number of the SK5468 PCB. If it is version 1. ,
insert the 90°, 1 pins headers into the SK5468 PCB, long tails
first, into the holes. Solder one pin, adjust the position then solder
the other pins. Cut flush. Do the same for both SK5468's.
Warning
WarningWarning
Warning : the pin headers must sit perfectly
perpendicular to the PCB surface for a good matching with
the main PCB.
Remove the 2 screws from the transformer pin side and
place 2 nylon washers on the holes.
Insert one SK5468 PCB on top of the transformer,
checking the pins number correspondence. Assemble with
the 2 screws. Solder the transformer pins.
Place the second SK5468 PCB on the other side of
the transformer, white text hidden. Assemble with the
last 2 provided screws.
Insert the transformer into the main PCB and solder
the pins.
27.
27.27.
27. Visual check
Visual checkVisual check
Visual check
At this point, brush the solder side with a hard tooth brush to remove any remaining solder bits.
Make a full visual check. Any missing component on the board ? Any remaining component in the box ?
When everything looks correct, proceed with the frame assembly.
28.
28.28.
28. Frame assembly
Frame assemblyFrame assembly
Frame assembly
Insert 4 M x 5mm countersunk screws into the side plate for the output transformer assembly. On each
screw, insert 1 shakeproof washer, one metal M washer and one M nut, in this order. Tighten.
Assemble the front plate and the side plate with 2 M x6mm countersunk black screws.
Warning
WarningWarning
Warning : Do not confuse the M x6mm countersunk black screws with the #4-40 /8" black screw that
are used to attach the module in the lunchbox.
Copyright ©2010 SoundSkulptor
Plate
washer
nut
shakeproof
M x 5 screw

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 07/01/15
MP57 Assembly guide
MP57 Assembly guideMP57 Assembly guide
MP57 Assembly guide
Copyright ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 13/08/10
Di01 Assembl guide
Di01 Assembl guideDi01 Assembl guide
Di01 Assembl guide
Safet warning
Safet warningSafet warning
Safet warning
The kits are main powered and use potentiall lethal voltages. Under no circumstance should someone undertake the
realisation of a kit unless he has full knowledge about safel handling main powered devices.
Please read the “DIY guide” before beginning.
Print or open the following documents :
•Di01 Schematics
•Di01 Components la out
•Di01 Parts list
Follow this guide from item number 1 till the end, in this order. The assembl order is based on components height, from
low to high profile, in order to ease the soldering process : The component ou are soldering is alwa s taller than the
previousl assembled ones and it is pressing nicel against the work area foam.
Cop right ©2010 SoundSkulptor

www.soundskulptor.com
Document revision 1.1 – Last modification : 13/08/10
Cop right ©2010 SoundSkulptor