Sound Storm SHP User manual

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure tolocate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock.Refer any repairs to a
qualified service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
TheSHP is an additional set of
wireless headphones for use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphone controls and features
4SHP-IR features
5System wiring:
SHP-IR transmitter
6Headphone battery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on yourpurchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thankyou for making Sound Storm
Laboratoriesyour choice incar audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IRand
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.
L A B O R A T O R I E S
®

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure tolocate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
Please read this manual completely
and carefully prior to attempting to
install your new Sound Storm mobile
audio/video equipment. Installed
correctly, your Sound Storm
equipment will provide youwith years
of enjoyable and safe usage.
Installation of this equipment in any
portion of a vehicle which impairs or
distracts the driver is improper and
dangerous. Sound Storm assumes no
liability whatsoever for failure tofollow
the proper installation of this product.
Please keep this manual in a safe place
for future reference.
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock.Refer any repairs to a
qualified service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
Installation precautions
Do not install components in areas
which are susceptible to rain, moisture,
direct sunlight,extreme heat or cold,
excessive dust, dirt or humidity.
Use only the installation parts and
hardware provided with the unit to
ensure proper installation. Usingother
parts can cause malfunction and
possible damage to your Sound Storm
headphone system.
Use only a power source with 12Volts
DC (negative ground).
Before final installation, temporarily
connect the wiring according to the
diagram near the end of this manual,
check it to ensure that it has been
connected properly, and test the unit
to make sure it is working correctly.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
What is included?
TheSHP-IR wireless infrared audio
system includes:
• Wireless audio transmitter
• (2) wireless headphones
TheSHP is an additional set of
wireless headphones for use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure tolocate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
IR SENSORS
1
VOLUME CONTROL KNOB
2
SYMPTOM CAUSE REMEDY
POWER ON/OFF SWITCH
This buttonturns the headphone on
and off.
In addition, if headphones do not
receive any infrared audio signal after
a short period of time, they will shut
off automatically to conserve battery
life.
3
6BATTERY COVER
See the section of this manual about
battery replacement for more details.
4POWER LED 5
SHP-IR Wireless Headphones with IR Audio Transmitter
2
6
3
4
1
5
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure tolocate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
SHP-IR
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
IR EMITTERS (AUDIO TRANSMITTERS)
1
1
MOUNTING HOLE
2
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.
2 2

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure tolocate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
System wiring: SHP-IR Transmitter
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.
AUDIO/VIDEO
SOURCE
(DVD player,
video game, etc.)
BLACK
to Chassis Ground
LEFT AUDIO
OUTPUT
RIGHT AUDIO
OUTPUT
WHITE
RED
RED
FUSE 12V
Battery
SHP-IR

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure to locate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
Thewireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve batterylife, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IR reception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system orSound Storm
monitors with wireless infrared audio
transmission capability.
Installing or replacing headphone batteries
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure to locate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
The wireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve battery life, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IRreception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
Several Sound Storm videomonitors include a wireless infrared transmitter. The
transmittersends a high-quality stereo signal which can be received the SHP
wireless infrared headphones.
Theinfrared signal is emitted from the large dark lens on the front of the monitor
console. Best sound will be obtained if you sit directly in front of the monitorwithin
about six feet. If you choose to sit to one side of the monitor, you can expect good
reception within 35º to the right or left of the monitor.
Using the SHP headphoneswith a Sound Storm Monitor
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.

Using the wires provided, complete the audio, and power connections in your
vehicle as shown in the diagram below.
Be sure to locate the transmitter in a location and position within direct line-of-sight
of the location in the vehicle you plan to have passengers wearing headphones.
The wireless headphones use (2) AAA batteries (not included), which are located
in one of the earphone housings.
To replace the batteries, follow the diagrams below. To conserve battery life, please
be sure to turn off the headphones whenever they are not in use, even though they
will turn off after a short period of interrupted IRreception. If you expect the
headphones to be unused for several days, remove and store the batteries.
CONTENTS
SHP-IR • SHP User’s Manual - Contents
SHP-IR • SHP User’s Manual - page 5
SHP-IR • SHP User’s Manual - page 2
General precautions
Safety precautions
SHP-IR and SHP Headphone Controls and Features
SHP-IR • SHP User’s Manual - page 3
Troubleshooting
SHP-IR • SHP User’s Manual - page 8
SHP-IR • SHP User’s Manual - page 7
SHP-IR Transmitter Features
SHP-IR • SHP User’s Manual - page 4
SHP-IR • SHP User’s Manual - page 6
U S E R ’ S M A N U A L
Specifications
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
may be present which may result in
electric shock. Refer any repairs to a
qualified service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• If there is smoke or any peculiar odor
present during use or if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible.
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
No audio present
in headphones.
Power cord is not
properly connected.
Audioinput cables not
properly connected.
Audioinput source is not
operating properly.
Batteries are dead.
Check that power connections
are properly made and all fuses
are in functioning condition.
Check all cables.
Replace or repair A/V source
(DVD player, video game, etc.)
Replace headphone batteries.
Sound is of poor
quality or has
interruptions and
dropouts.
Headphone is not being
used in direct line-of-sight
with the player orremote
IR sensor. Transmission
is best within 6 feet/35º
angle of IR sensor on the
monitor.
Move to a better location. If this
is not possible, consider a more
suitable location for the
transmitter.
The SHP is an additional set of
wireless headphonesfor use with
the SHP-IR system or Sound Storm
monitors with wireless infrared audio
transmission capability.
2General precautions
2Safety precautions
2Installation precautions
2What is included?
3Headphonecontrols and features
4SHP-IR features
5Systemwiring:
SHP-IR transmitter
6Headphonebattery replacement
7Using SHP with a monitor with
built-in IR audio transmitter
8Troubleshooting
8Specifications
Congratulations on your purchase
of a Sound Storm Laboratories
wireless infrared headphone
system.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of listening
pleasure.
Thank you for making Sound Storm
Laboratories your choice in car audio
and video entertainment!
page
SHP-IR
Wireless Infrared Headphone System
(Two Headphones and Transmitter)
SHP
Wireless Headphones
(for use with Sound Storm SHP-IR and
Sound Storm Monitors with Infrared
Audio Transmission)
All specifications subject to change without notice.
Transmission system
Carrier frequency
Modulation
Mode
S/N ratio
Channel separation
Distortion
Frequency response
Power source, headphones
Current consumption, headphones
Infrared light
2.3 MHz (left channel), 2.8MHz (right channel)
FM
Stereo
greater than 60 dB
greater than 40 dB
les than 1%
30Hz - 20kHz
(2) x AAA batteries
25 mA max (during play) / 15mA (muted)
SHP Wireless Headphones MODEL
SYMPTOM CAUSE REMEDY
SHP-IR Wireless Headphones with IR Audio Transmitter
Lift battery door release latch.
Lift and remove battery door.
Insert two AAA type batteries (not
included). Be sure to note proper
polarity when installing the batteries.
L A B O R A T O R I E S
®