manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. SoundOFF
  6. •
  7. Grill
  8. •
  9. SoundOFF PREDATOR EPRDSGS1 User manual

SoundOFF PREDATOR EPRDSGS1 User manual

EPRDSGS1(x) 02/08
WARNING
: Warning devices are strictly
regulated and governed by Federal, State and
Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole
responsibility of the user of these devices to
ensure compliance.
BRACKET MOUNTING
Important: DO NOT over tighten
mounting screws or nuts. This could
cause permanent damage to the bracket
1. Locate flat mounting location for
Predator Light Bracket.
2. When position of bracket is determined
use supplied template for hole
locations.
3. Drive in Customer Supplied Hex Head
screws. Leave about a 1/16” space
between the mounting surface and
underside of screw head.
4. Place Light over screws using the
holes in brackets and slide to the right
to lock the brackets underneath the
head of the bolts.
5. Using a open-end wrench, tighten the
hex head bolts down tight to secure
the light to the mounting surface.
6. Adjust angle of the light to best suit
your application by loosening the 2
nuts on either end of the light.
7. After the Predator is set to the desired
angle, tighten the 2 nuts on either end
of the light. DO NOT OVER TIGHTEN
nuts as damage to bracket or light can
occur. Tighten nut until snug plus 1/8
turn.
8. Make electrical connections using the
following instructions.
!
WARNING
This product contains high intensity LED
devices. To prevent eye damage, DO NOT
stare into light beam at close range.
NOTE: The PREDATOR is a factory sealed
unit that CANNOT be serviced in the
field. Any attempt to gain access to the
PREDATOR unit will most likely cause
permanent damage and void its warranty.
IMPORTANT: DO NOT connect this
device to a strobe power supply.
OPERATING INSTRUCTIONS
See setup procedure on second page.
The single Predator comes equipped with
an internal flasher with 33 user selectable
patterns that can be synchronized either
alternating or simultaneous with up to
three other lights. It can also be put into
slave mode and driven through an
external flasher.
1. Connect the PREDATOR BLACK wire to
a good, convenient ground.
2. Connect the PREDATOR RED wire to
one side of a user supplied on/off switch.
Connect the other side of the switch,
through a 5Amp fuse, to a source of
+10-16Vdc.
Install Screws (user supplied)
first using template on back
Place Light over screws using keyway in brackets
Slide Light to the Right and tighten screws using box end wrench
BY SOUNDOFF SIGNAL
SCREW PLACEMENT DRILL TEMPLATE
(Be sure to use appropriate drill size for your screw size)
2.77
SINGLE EXTERIOR
DECK / GRILLE
WARNING SYSTEM
ASSEMBLY INSTRUCTIONS
EPRDSGS1(x)
!
WARNING
This product contains high intensity LED
devices. To prevent eye damage, DO NOT
stare into light beam at close range.
EPRDSGS1(x) 02/08
BY SOUNDOFF SIGNAL
FLASH PATTERNS for
SINGLE HEAD EXTERIOR PREDATOR II (EP2SGS1(x))
X-Pattern Sequence
ID#1 > ID#4 > ID#2 > ID#3
X-Pattern Light Head Placement
ID#4 ID#2
ID#3 ID#1
Predator Sync Configuration Instructions
1. Set ID#
a. Identify which pattern and sequence you want and look up ID#s on table.
b. Connections
i. RED: +12Vdc
ii. WHT: +12Vdc (Note: you will need to disconnect after power is applied)
iii. BLK: Ground
c. Apply power to unit
d. Without disconnecting power from unit, disconnect WHT wire
e. Momentarily connect WHT to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 1 – 4
f. Disconnect power from unit to get out of ID mode.
2. Set Pattern
a. Reapply power to units.
b. Once all Light Head ID#s are configured, make sure all lights are flashing the
same pattern
c. Connect corresponding colored wires of all units together: RED to RED, etc.
d. Change Pattern
i. Momentarily connect WHT wires to Ground
ii. Observe pattern change on all lights connected
e. Insulate all wires by taping with electrical tape
3. Connect Master Switch for Application
a. IMPORTANT! Ensure WHT Pattern/Sync Wires are tied together
1LIGHT
Single Light Operation: Follow the ID Selection steps and set the LED3 to ID#1 if it is not already. NOTE: Steady
Burn is produced for patterns 9 & 10 in Single Operation.
2 LIGHTS
ALTERNATING: To obtainAlternating patterns, follow the ID SELECTION steps and set one LED3 to ID#1 and the
other to ID#3. Then proceed to the PATTERN SELECTION steps.
SIMULTANEOUS: To obtain Simultaneous patterns, follow the ID SELECTION steps and set both LED3 lights to
ID#1. Then proceed to PATTERN SELECTION steps.
4 LIGHTS
X-Pattern: To obtain X-patterns, follow the ID SELECTION steps and set one of the four LED3 lights to ID#1, one
to ID#2, one to ID#3, and one to ID#4. Then proceed to PATTERN SELECTION steps. NOTE: Be sure to mount
each LED3 in the correct placement based on ID#.
SLAVE MODE
The LED3 is capable of being activated through the use of a
user supplied flasher by putting it in slave mode.
1. Permanently connect the LED3 WHITE and BLACK wire to a
good, convenient ground.
2. Connect the LED3 RED wire, through a 5Amp fuse, to the
output of a +10-30Vdc switching flasher.
NOTE: The LED3 is a factory sealed unit that CANNOT be
serviced in the field. Any attempt to gain access to the LED3
unit will most likely cause permanent damage and void its
warranty.
PATTERN SELECTION
1. Disconnect WHITE wire from any
connections if applicable.
2. Turn PREDATOR II ON.
3. Momentarily touching and removing the WHITE
wire(s) to ground
will advance the PREDATOR II to the next flash
pattern. Touching and
removing the White wire for more than a few seconds
will allow you to change the PREDATOR II to the
previous pattern. See flash pattern table. Continuing
to touch and remove the WHITE wire(s) to ground will
allow you to scroll through the pattern list. After pattern
#33 is reached the list will start over again at pattern
#1.
NOTE: The PREDATOR II is equipped with flash
pattern memory. Once you have selected a pattern the
PREDATOR II will always activate to that pattern
every time the unit is turned on. Tape up and secure
WHITE wire so that it will not accidentally change your
selected pattern
PATTERN RESET
1. Remove power.
2. Place WHITE (sync) wire to ground.
3. With sync wire grounded, re-power RED wire.
4. Maintain for one second (light will dim).
5. Remove power and ground (pattern 1 set)..
SINGLE EXTERIOR
DECK / GRILLE
WARNING SYSTEM
ASSEMBLY INSTRUCTIONS
EPRDSGS1(x)

Popular Grill manuals by other brands

Smoke hollow PT300B Assembly, care & use manual warning & safety information

Smoke hollow

Smoke hollow PT300B Assembly, care & use manual warning & safety information

Philips HD6322 user manual

Philips

Philips HD6322 user manual

Ducane Affinity 31-3200 owner's manual

Ducane

Ducane Affinity 31-3200 owner's manual

TEFAL Plancha Booster manual

TEFAL

TEFAL Plancha Booster manual

Brandt Table Runner RAC2x4MG instruction manual

Brandt

Brandt Table Runner RAC2x4MG instruction manual

Char-Broil ADVANTAGE PRO Series operating instructions

Char-Broil

Char-Broil ADVANTAGE PRO Series operating instructions

Lund 99592 instructions

Lund

Lund 99592 instructions

Pit Boss 10697 Assembly and operation

Pit Boss

Pit Boss 10697 Assembly and operation

Adexa HEL-707A instruction manual

Adexa

Adexa HEL-707A instruction manual

Kenmore ELITE 141.16684 Operator's manual

Kenmore

Kenmore ELITE 141.16684 Operator's manual

Napoleon 410 instructions

Napoleon

Napoleon 410 instructions

Jumbuck PORTLAND Assembly & operation instructions

Jumbuck

Jumbuck PORTLAND Assembly & operation instructions

Duro 740-3024-BI Installation and user care guide

Duro

Duro 740-3024-BI Installation and user care guide

Lenoxx PG280 instruction manual

Lenoxx

Lenoxx PG280 instruction manual

gourmetmaxx KG 1000 instruction manual

gourmetmaxx

gourmetmaxx KG 1000 instruction manual

TOLE K60 user guide

TOLE

TOLE K60 user guide

Brinkmann 9400 owner's manual

Brinkmann

Brinkmann 9400 owner's manual

HOFFEN MGNK-H097 instruction manual

HOFFEN

HOFFEN MGNK-H097 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.