Sovereign SCS 37/1 User manual

Quick Start Guide
Your Safety is most important. Please read these safety rules before you use this machine
General Safety Rules
Read the user manual before using the machine
On all Jobs performed with the saw you must always wear safety googles to guard your eyes from flying materials/objects
and a sound-proof helmet, ear plugs or the like to protect your hearing. Wear a safety helmet if there is a risk of objects
falling on you from above.
Wear gloves to protect your hands
Wear safety shoes to protect your feet
Protect yourself from saw kickback. Hold the chain saw securely with both hands during use.
Make sure that the chain brake is released. Pull back the handle/chain brake before operating.
Noise emission complies with Directive 2000/14/EC!
Warning! Danger!
Note - This quick start guide is intended for experi-
enced users who have already assembled the tool,
please refer to the manual for further details

Quick Start Guide
1Unpack the Chainsaw
a) Open carton carefully and remove all parts
b) Ensure you have all items (see above) before you discard the packaging
2Guide Bar installation
a) Make sure the chain lever is pulled back into the designated Position (a firm click should be felt and heard when in position) (Fig. 3a)
b) Remove the 2 fastening nuts (B) (Fig. 3b) then ease off the chain cover including the chain brake handle (C) (Fig. 3b)
c) Before attempting to fit the chain bar ensure the transit packaging item 24 is removed (Fig. 3c)
d) Using a screwdriver, turn the adjustment screw (D) anti clockwise until the TANG (E) (projecting prong) is to the end of Its travel towards
the clutch drum and the sprocket (Fig. 3c)
e) Place the slotted end of the guide bar over the bar bolts (F) Position the bar so the adjustment TANG (projecting prong) fits into the lower
Hole (G) on the guide BAR (Fig. 3d).
3Installing the saw Chain
a) Spread chain out in a loop with cutting edges (A) Pointing CLOCKWISE around the loop
b) Slip the chain around the sprocket (B) behind the clutch (C), make sure the links fit between the sprocket teeth (Fig. 4b)
c) Guide the drive links into the groove and around the edge of the bar (Fig. 4b)
d) Pull the chain bar forward until the chain is closely seated, checking that the TANG (Projecting prong is still located in position.
e) Install the chain cover & Install the 2 nuts tightly
f) Before you start to use the saw you must Tensionthe chain by adjusting the tension screw D clockwise until the chain fits snugly all the
way around, but can still be moved easily. The should be bar 2 mm to 3 mm of play between the chain bar and the chain.
Items Included
Saw Chain (not
attached to chain
bar
Chain Bar
Chain Saw Unit
EH 09/2007
B
3B3A
D
F
G
E
3C 3D
24
A
D
B
C
4A 4B 3A
D
Chain Brake
4Fuel / Lubrication
a) Mix the fuel in the mixer bottle provided
b) Shake the container gently to ensure that it is properly mixed.
N.B Failure to use the correct oil/fuel mixture
will cause the engine to seize
Fuel Mixture is 50:1 (50 parts Fuel
to 1 part 2 stroke oil)
Use regular grade unleaded
petrol and quality 2 stroke oil
5Starting the Chainsaw
a) Add the fuel & Chain oil to the saw
b) Switch Ignition to “I” (on)
c) Take Brake off by pushing the lever back
d) Pull choke fully ou untiil it locks
e) Push primer bubble 10 times
f) Pull starter cord rapidly 4 or 5 times
NOTE: amount of choke will vary slightly
Depending on the external temperature
g) Allow engine to warm up at half throttle for
a short time and then push the choke in fully
Ignition Switch
Mixed Fuel Chain Oil
Choke Lever
C
Primer Bubble
THE CHAINSAW WILL NOT START IF THE
EMERGENCY STOP HANDLE IS PUSHED
FORWARD
Do you have questions?
We can help
Call Customer Service
Mon-Thur 08:45 am - 5:00 pm
Friday 08:45 am - 3:15 pm
岼
0151 649 1500
Spare Parts also available