Spectrum Industries 95532 User manual

Note: Before proceeding with this installation, the display stand should be
fully-assembled on the table. The shroud works with one 37”-63” monitor.
1/4-20 x 15mm
JC bolts
(4 required)
Back
panel
0116554R2 Page 1 of 5
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Display Shroud
for InVision Display Stand
95532
1. Remove monitor mount
If the monitor mount is installed, it will need to be removed from the
display stand before installing the shroud.
1. To remove the monitor mount, rst remove the (4) 1/4-20 x 15mm
JC bolts and back panel. Figure 1A.
(2) 0116551
Shroud
(10) 026059
1/4” Washer
(10) 034195
1/4-20 Wing nut
(4) 0106417
1/4-20 x 1/2”
Carriage bolt
Monitor mount
Figure 1A
Display stand
4mm Hex
wrench
Tools Required
7/16” or
adjustable
wrench
(1) 0116552
Shroud base plate

0116554R2 Page 2 of 5
Figure 1B
1/4-20 x 30mm
JC bolts
(6 required)
2. Remove the (6) 1/4-20 x 30mm JC bolts, and 1/4-20 locknuts
and set the mount aside. Retain all fasteners. Figure 1B.
1/4-20 locknuts
and washers
2. Install shroud base plate
1. Two sets of mounting holes are available for the shroud / monitor
mount. Choose a set of holes based on your monitor size and
preferred height. Figure 2A. Typical installations use the upper
holes for better viewing and clearance.
Two-vertical positions available
Figure 2A
Monitor
mount
plate

Shroud
base plate
0116554R2 Page 3 of 5
2. Loosen the (4) 1/4-20 x 30mm JC bolts on the display
stand laminate panel. Figure 2B.
3. Using the (4) keyholes in the shroud base plate, hang
the shroud base plate on the loosened JC bolts.
4. Secure the shroud base plate and monitor mount
plate to the display stand with (6) 1/4-20 x 30mm JC
bolts, 1/4” washers, and 1/4-20 locknuts. Tighten
bolts equally and securely.
Monitor mount plate
1/4-20 x 30mm
JC bolts
(6 required)
1/4-20 locknuts
and washers
Display stand
Figure 2B
3. Install monitor
• Install monitor to display stand. Figure 3.
• Refer to the instructions included with the monitor mount for complete
monitor installation procedure.
• The assembled display stand accommodates most 37”-63” monitors. Do
not exceed the available monitor weight capacities. See chart below.
Figure 3
Added InVision Access option Weight
capacity
available
for installed
monitor
Display
Shroud
95532
-38 lbs
Dual
Display
Mount
37124
-29 lbs
Camera
Mount
37108
-7 lbs
InVision Access
Display Stand
37120
(100 lb capacity)
ü= 62 lbs
ü ü = 55 lbs
No additional options added = 100 lbs
*Note: The display shroud is not
compatible with the dual display mount.
Monitor

0116554R2 Page 4 of 5
4. Install monitor shrouds
1. Align the mounting holes of each monitor shroud with the shroud base plate. Figure 4.
Each shroud will attach behind the shroud base plate (display stand-side).
2. Place the shroud slots over the base plate weld studs and move the shroud to the widest position rst, then
adjust to t the monitor. Leave 1-2 inches between the edge of the monitor and angled portion of the shroud
to maximize sound projection from behind the monitor.
3. Secure each shroud to the base plate with (2) 1/4-20 x 1/2” carriage bolts, (5) 1/4” washers, and (5) 1/4-20
wing nuts. Place the carriage bolts in the closest available mounting holes next to the shroud.
4. Make sure both shrouds are equally spaced from the monitor edges and tighten the wing nuts securely.
1/4-20 x 1/2”
Carriage bolt
Figure 4
1/4” Washer
1/4-20
Wing nut
1/4-20 x 1/2”
Carriage bolt
1/4-20 x 1/2”
Carriage bolt
Shroud
Shroud
Shroud base
plate
Display
stand
1-2”
1-2”
Weld stud
Weld stud
1/4-20 x 1/2”
Carriage bolt
Installed
monitor

0116554R2 Page 5 of 5
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2016 Spectrum Industries Inc., All rights reserved.
5. Route monitor wiring and install back panel
1. Route cords / wires to the monitor using the wiring tray and
grommets. Wire routing options are shown in Figure 5.
2. After all wiring has been completed, install the back panel with (4)
1/4-20 x 15mm JC bolts and tighten securely.
Figure 5
1/4-20 x 15mm
JC bolts (4 required)
Back
panel
Wiring tray to
technology
compartment
Wiring
over top
Wiring to
oor or wall
Installed
monitor
WARNING
The monitor should always be lifted
off the stand before moving the table.