Spectrum industries Lt-30 User manual

057880R9 Page 1 of 7

To purchase parts or accessories, please contact us at

www.spectrumfurniture.com

1-800-235-1262

Thank you for purchasing Spectrum products!

Spectrum Industries, Inc

Chippewa Falls, WI 54729, USA

Owner’s Manual

CAUTION:

Before using this product, read this manual and follow

all safety and operating instructions.

Before you begin, please make sure all parts and

proper quantities are included. Any parts damaged

during shipment must be reported within 15 days of

receipt. To report information regarding damages or if

you have any questions, please call 1-800-235-1262.

Spectrum Industries, Inc

Chippewa Falls, WI 54729, USA

55210SR LT-30 Laptop Cart

55214SR xLT-24 Laptop Cart

LT-30, XLT-24 Laptop Carts

Safety

Hardware package contents Tools required

Assembly / Setup

1. Handle assembly

2. Handle installation

057880R9 Page 2 of 7

A. Attach the handle gusset and handle mounts to the bottom of the handle using

1/4-20 x 15mm JC bolts as shown in Figure 1. Do not tighten completely.

4mm hex wrench

(included)

(1) 025039

4mm hex wrench

(2) 055001

handle mount

(1) 052577

handle gusset

7/16” or adjustable wrench

1/4-20 x 15mm JC

bolt w/ locknut

handle mount

Figure 1

Figure 2

A. Determine which side of the cart you would like the handle to be mounted, and open both doors.

B. Attach the handle assembly to the side of the cart with (4) 1/4-20 x 15mm JC bolts as shown in Figure 2 and tighten all bolts securely.

Note: The 2 outer bolts will need a locknut on the inside of the cart.

C. Install (2) pinetree buttons (center holes) on the side panel that does not have the handle attached, and 3/8” hole plugs in the remaining

open side panel holes.

handle

(2) 035252

3/16” x 1/2”

pinetree button

(10) 052605

1/4-20 x 15mm JC bolts

(30) 0110254-5

2” Velcro®hook & loop

(8) 044555

3/8” hole plug

(90) 052608

5” x 3/4” Velcro®wrap

(2) 041943

1/4-20 locknut

handle

gusset

handle

mount 1/4-20 x 15mm

JC bolts

Note: It is critical that all fasteners be

used in the attachment of the handle.

1/4-20 x 15mm

JC bolt

1/4-20 x 15mm JC

bolt w/ locknut

1/4-20 x 15mm

JC bolts

• Read this owner’s manual before assembly or operation.

• Do not allow children to move cart.

• Move slowly and carefully when mobile.

• For indoor use only. Do not install or store the unit where it will be exposed to weather. Keep unit dry.

• For added safety, plug the unit into a grounded three-prong receptacle controlled by a GFI

(Ground Fault Interrupter) circuit breaker.

3. Cord management

4. Power strip operation

A. Using the cord management slots in the trays, and Velcro straps provided, bundle the charge cords.

Figure 4 shows a typical wiring example. Be sure to leave enough slack in the power cord to allow the tray to be pulled out.

B. Route the charging plug to the student-side of the tray to allow easy-access and removal. Anchor with a Velcro strap.

C. Adhesive-backed Velcro hook & loop strips are also provided to attach the charging transformer to the tray if necessary.

A. With the main power cord unplugged and the power strip switched off, plug the laptop

charge cords into the power strip. Figure 4.

B. The power strip can be turned on and off with the main power switch. The breaker can be

reset in the event of an overload with the reset button.

057880R9 Page 3 of 7

Velcro straps

Laptop

charging

transformer

Figure 3

student-side

instructor-side

bundled charge cords

with Velcro strap

power cord (leave enough

slack to pull out tray)

power strip

reset button power switch

Figure 4

5. Power connections

057880R9 Page 4 of 7

A. Insert the cord reel plug through the lower grommet. Figure 5.

B. Plug the cycle charger plug into the cord reel power plug as shown.

C. Plug the power strip into the second cycle charger plug as shown. Additional accessories can now be powered from the power strip.

Note: The master switch on the cycle charger needs to be switched to the ‘AUX’ position to use the power strip.

auxiliary power

plug from cycle

charger

cord reel

to wall plug

Figure 5

cord wraps

CYCLE

A B

AUX

OFF

AUX

15 240

120

180

Timer operation

Cord reel operation

1.) Plug the power cord into a 110-volt standard outlet.

2.) Plug the appropriate equipment into both side “A” & “B”. Toggle the master

switch to the “CHARGE” position.

3.) To charge Side “A” ONLY, toggle the cycle switch to the “A” position.

4.) To charge Side “B” ONLY, toggle the cycle switch to the “B” position.

5.) To cycle charge BOTH “A & B”, toggle the cycle switch to the “CYCLE” position. Set the timer to the

preferred cycling increment. After side “A” expires, the timer will activate side “B” for the same period of

time and will continue to do so until the master switch is set to the “OFF” position.

The Cart timer is a 240 minute timed switch that provides accurate timing between 15 - 240 minute

increments and is easy to set and operate.

The cycle timer is located on the instructor-side of the unit. The timer has 24 (XLT-24) or 30 (LT-30) outlets

which are controlled by the red lighted master switch. The master switch is a 3-position rocker switch. The

timer controls the outlets on side “A” & “B” (12 or 15 on each side) designated for the charging of laptops.

The outlets are controlled by the cycle switch and can alternate charging time between cycle A and B. The

7-outlet power strip located on the student-side may be used for various auxiliary applications.

057880R9 Page 5 of 7

CAUTION

The purpose of the timer is to prevent power overload while charging laptops in conjunction with

peripheral components. The charge mode is independent of the auxiliary mode to minimize risk of power

overage. To provide charging power to laptops, toggle the master switch to “CHRG”. To provide power to

peripheral components, toggle the master switch to “AUX”.

Master Switch

Cycle Switch

Timer

Figure 6

Operating Instructions:

1. To latch cord - Pull cord out to full length. Allow the cord to retract 1-2 feet back into

the reel. Pull the cord out slowly. When a ‘click’ is heard, the cord will latch in place.

2. Plug into 110-125V (single phase), 3-conductor wall outlet.

3. To release cord - Unplug from wall outlet. Pull cord out slowly until clicking stops.

The latch will release and the cord can be guided back into the reel. Do not allow the

cord to y unrestricted back into the reel.

4. Do not overload or circuit breaker (15-amp maximum) will cut off current. To restore

power, remove overload, wait two minutes, then reset the circuit breaker by pressing

the button on the back of the 3-prong male power plug.

Maintenance:

1. Remove dirt and grime as soon as it accumulates on the reel case by using a soft,

damp cloth (a mild detergent may be used if needed), being careful not to wet

the electrical plug. Never immerse any part of the unit in any solution to clean.

DO NOT use solvents such as gasoline, turpentine, etc. to clean unit.

2. Keep cord clean to assure smoothest automatic retraction. Simply pull cord to its

full length and allow to retract through a dampened rag. Pull out full length again

and sprinkle cord with talcum powder.

Specications:

15’ retractable, 15-amp, 125V, 12 AWG with breaker, UL listed

WARNING

• This cord reel is intended for general indoor use only. It is not intended to be used

in potentially dangerous locations such as ammable or explosive atmospheres.

The reel is not waterproof and not intended for use in potentially wet locations.

• Do not overload (15-amp maximum).

reset button

power plug

Moving the cart

Options

057880R9 Page 6 of 7

Second Handle

20”W x 4”D

(mounts on either side)

55171

Tray Edge Trim

30 pieces

(applied to shelf pull edge)

55172

Replacement Key Set

55142

7-Outlet Power Strip, insured

with surge protector, and 12’ cord

10”W x 2”D x 11/8”H

99024

A. Before moving the unit, unplug and retract the power cord.

B. Be sure the casters are in the unlocked position and the doors closed.

C. Move the cart slowly and carefully.

D. Lock the casters after moving.

Warranty

925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph:800-235-1262, 715-723-6750 Fax: 800-335-0473, 715-738-2309

E-mail: [email protected] web: www.spectrumfurniture.com

057880R9 Page 7 of 7

WE WILL MAKE IT RIGHT FOR YOU!

Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available and each

product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).

Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or concerns. We are available

to answer your calls Monday through Friday from 7 am to 5 pm CST, excluding observed holidays. In addition your product comments or concerns are

welcome via e-mail at: [email protected].

Warranty Statement

We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten years. Any item

deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at Spectrum’s discretion. This

warranty applies to all products manufactured and distributed by Spectrum except the products

listed below.

Items that have a varying warranty include, but are not limited to, the following:

• Adjustable Crank/Electric Desk Legs (1 yr)

• Flat Panel Desk Gas Cylinders (1 yr)

• Upholstered Soft-Goods (5 yrs)

• Adjustable Height & Stacking Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles (7 yrs)

• Adjustable Height & Stacking Chair Casters (2 yrs)

• Chair Upholstery & Textiles (2 yrs of normal use of Soft Goods, Adjustable Height, Stacking, Wood and Metal Chairs)

• Chair Upholstery - Graded-In Fabrics and C.O.M (no warranty)

• Height Adjustable Columns and Lifts (1 yr)

• General Use Casters (1 yr)

• Electrical – Electri-Pak, Power Communication Modules, and special order ECA electrical items (1 yr)

• Electrical - Power Strips & Electrical Timers (1 yr)

• Electrical Surge Suppressors (lifetime)

• Electrical - Retractable Power Cords (1 yr)

• Keyboard/Mouse Trays (1 yr)

• Flat Panel Monitor Arm – General Parts (5 yrs)

• Flat Panel Monitor Arm – Gas Cylinders (2 yrs)

• CRT Monitor Arm (1 yr)

Warranty is void if product is not used for its intended purpose or subjected to an unusual application, multiple-shift use, alteration, accident, abuse or

abnormal wear and tear. Representations of colors on-line and in printed materials are meant to be a close reference to the actual colors but not an

exact match. Slight variations in color and texture of wood stains, powder coating, laminates, fabrics and other materials are normal in different manu-

facturing lots; as such these variations are not considered defects.

DESIGNED FOR INDOOR USE ONLY – Unless speciﬁcally stated in the product speciﬁcations, Spectrum’s products have been designed and con-

structed for indoor use only. Moving or using outdoors, or on excessively rough surfaces, may cause damage to the products and will void the warranty.