Spectrum Industries LT-30 User manual

55325
net LT-30 Netbook Cart
net LT-30 w/ 5" balloon wheels
Owner's Manual
0107093XR4 Page 1 of 9
Owner's Manual
IMPORTANT:
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within 15
days of receipt. To report information regarding damages or if you have any
questions, please call 1-800-235-1262.
CAUTION:
Before using this product, read this manual and follow all safety and
operating instructions.
Spectrum Industries, Inc.
Chippewa Falls, WI 54729, USA
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!

Safety
Hardware Package Contents
Assembly / Setup
●Read this owners manual before assembly or operation
●Do not allow children to move cart
●Move slowly and carefully when mobile
●Do not use auxiliary outlets on cycle timer to charge laptops-use 'A' and 'B' outlets only
Tools Required:
7/16" or Adjustable Wrench4mm Hex Wrench
(included)
(2) 055001
Handle Mount
(10) 052605
1/4-20 x15mm JC Bolts
(1) 052577
Handle Gusset
(1) 025039
4mm Hex
Wrench
(30) 052597-8
2" x 3" self -adhesive
Velcro
(45) 052608
3/4" x 5" Velcro
Straps
(8) 035252
3/16" x 1/2" Pine
tree Button
(3) 042919
5/16" Hole Plug (32) 058305 1/4" Hole Plug
Handle Assembly
A. Attach the handle gusset and handle mounts to the bottom of the
handle using 1/4-20 x 15mm JC Bolts as shown in Figure 1.
Dttiht ltl
0107093XR4 Page 2 of 9
Safety
Hardware Package Contents
Assembly / Setup
Read this owners manual before assembly or operation
Do not allow children to move cart
Move slowly and carefully when mobile
Do not use auxiliary outlets on cycle timer to charge laptops-use 'A' and 'B' outlets only
Tools Required:
7/16" or Adjustable Wrench4mm Hex Wrench
(included)
(2) 055001
Handle Mount
(10) 052605
1/4-20 x15mm JC Bolts
(1) 052577
Handle Gusset
(1) 025039
4mm Hex
Wrench
(30) 052597-8
2" x 3" self -adhesive
Velcro
(45) 052608
3/4" x 5" Velcro
Straps
(8) 035252
3/16" x 1/2" Pine
tree Button
(3) 042919
5/16" Hole Plug (32) 058305 1/4" Hole Plug
Handle Assembly
A. Attach the handle gusset and handle mounts to the bottom of the
handle using 1/4-20 x 15mm JC Bolts as shown in Figure 1.
Do not tighten completely.
Note: It is critical that all
fasteners be used in the
attachment of the handle.
Handle
Handle
Gusset
Handle
Mount
1/4-20 x 15mm
JC Bolts
1/4-20 x 15mm
JC Bolts
1/4-20 x 15mm JC Bolt
1/4-20 x 15mm JC Bolt
Handle
Mount
1/4-20 x 15mm
JC Bolts
Figure 2
Figure 1

Handle Installation
Hole Plug Installation
A. Determine which side of the lectern you would like the handle to be mounted, and open both doors.
Note: This unit comes with the doors hinged on the power strip-side. This is useful if the unit is going
to be placed against a wall. If the unit is to be placed against a wall, install the handle opposite the hinges.
B. Attach the handle assembly to the side of the lectern with (4) 1/4-20 x 15mm JC bolts. As shown in Figure 2.
C. Tighten all bolts securely.
A. If one side of the unit will not have a handle or flip-up documentcamera shelf attached,
install pine tree buttons in the unused mounting holes as shown. Figure 3.
B. Install (3) 5/16" hole plugs in the center of the side panel.
C. Install 1/4" hole plugs and pine tree buttons in the remaining open holes as shown.
1/4" Hole Plugs
Handle
0107093XR4 Page 3 of 9
Handle Installation
Hole Plug Installation
A. Determine which side of the lectern you would like the handle to be mounted, and open both doors.
Note: This unit comes with the doors hinged on the power strip-side. This is useful if the unit is going
to be placed against a wall. If the unit is to be placed against a wall, install the handle opposite the hinges.
B. Attach the handle assembly to the side of the lectern with (4) 1/4-20 x 15mm JC bolts. As shown in Figure 2.
C. Tighten all bolts securely.
A. If one side of the unit will not have a handle or flip-up documentcamera shelf attached,
install pine tree buttons in the unused mounting holes as shown. Figure 3.
B. Install (3) 5/16" hole plugs in the center of the side panel.
C. Install 1/4" hole plugs and pine tree buttons in the remaining open holes as shown.
Figure 3
Pine tree Buttons
5/16" Hole Plugs
(3 req'd)
1/4" Hole Plugs
Corner Column
1/4" Hole Plugs
Handle
Pine tree Button
Pine tree Button

Mini Laptop / Netbook Cord Management
A. Netbookscan be oriented in the tray one of two ways depending on their size. Smaller netbooks typically are located side-by-side, and
larger ones front-to-back. Check the size of your specific netbooks to see which mounting method will work best. See Figure 4.
B. Be sure the cart power strip cord(s) are unplugged.
C. Attach the netbook charging transformers to the laptop trays using adhesive Velcro pads or zip ties/Velcro straps and cord slots.
(Excess cords can be bundled with the transformer if necessary.) Be sure to leave enough slack in the cords for the tray to pull out fully.
D. With the power strip switches in the 'OFF' position, plug the netbook transformers into the power strips, and the transformers into the
netbooks.
Larger Mini Laptops/NetbooksSmaller Mini Laptops/Netbooks
Charging
Transformers
Netbook
Netbook
Netbook
Netbook
Plugs to
Power
Strips
Laptop Tray Laptop Tray
Plugs to
Power
Strips
0107093XR4 Page 4 of 9
Mini Laptop / Netbook Cord Management
A. Netbookscan be oriented in the tray one of two ways depending on their size. Smaller netbooks typically are located side-by-side, and
larger ones front-to-back. Check the size of your specific netbooks to see which mounting method will work best. See Figure 4.
B. Be sure the cart power strip cord(s) are unplugged.
C. Attach the netbook charging transformers to the laptop trays using adhesive Velcro pads or zip ties/Velcro straps and cord slots.
(Excess cords can be bundled with the transformer if necessary.) Be sure to leave enough slack in the cords for the tray to pull out fully.
D. With the power strip switches in the 'OFF' position, plug the netbook transformers into the power strips, and the transformers into the
netbooks.
Snap-in Clip
Larger Mini Laptops/NetbooksSmaller Mini Laptops/Netbooks
Figure 4
Charging Transformers
Charging
Transformers
Netbook
Netbook
Netbook
Netbook
Plugs to
Power
Strips
Laptop Tray Laptop Tray
Snap-in Clip
Plugs to
Power
Strips
Power Strip Operation
A. With the main power cord unplugged and the power strips turned off, plug the laptop
charge cords into the power strips. Figure 5&6.
B. With all switches in the 'OFF' position, plug the power strip plugs into the 'A' and 'B'
timer outlets. Figure 7.
C. Plug the timer into the cord reel and the cord reel into a wall outlet.
D. Switch on the power strips to charge. The power strip can be turned on and off with
the main power switches. The breaker can be reset in the event of an overload with
the reset button.
Figure 5
Power switch
Reset button
Power Strips

16-outlet Power Strips
Snap-in Clips
Bottom Power
Strip Mount
Divider Panel
Cycle
Timer
Power
strips plug
in here
AUX
Outlets
0107093XR4 Page 5 of 9
16-outlet Power Strips
Figure 7
Snap-in Clips
Bottom Power
Strip Mount
Divider Panel
Cycle
Timer
Power
strips plug
in here
CAUTION
This Laptop Cart features two separate 16-outlet charging circuits on separate cords.
Some laptop notebook computers may draw more than 1/2amp when fully discharged.
If that is the case, plugging the two power cords into separate 15-amp electrical outlets
will prevent an electrical overload which may trip a circuit breaker. Please consult the
owners manual of the specific laptop computer for further information.
AUX
Outlets
WARNING
UNIT CAN TIP OVER RESULTING IN RISK OF INJURY.
DO NOT ALLOW CHILDREN UNDER 16 TO MOVE
CART. MOVE SLOWLY. DO NOT EXCEED A
MAXIMUM LOAD OF 100 LBS ON THE TOP
WORKSURFACE. DO NOT EXCEED A MAXIMUM
LOAD OF 7 LBS PER LAPTOP TRAY.
A. Before moving the unit, unplug all power cords.
B. Be sure the casters are in the unlocked position, doors are closed,
and any shelves are in the lowered position.
C. Move the unit using the handle.
D. After moving, lock the casters.
Moving the Lectern
Figure 6

Value Cycle Timer Operation
Using Timer:
The timer prevents overload by alternating power betweenboth power strips in the cart, providing charging to multiple laptops during
the day. The power strips plug into the outlets labeled 'A' or 'B'.
The timer control can be adjusted between 15-240 minutes. This is the number of minutes a power strip will be "hot" before the
ti it h t th th t i
15 i t b d th d f lt tti b t th ti tti ill d d th
lt
On / Off Switch
(Controls power to timer &
'A' and 'B' outlets)
Timer Control Auxiliary
(constant-power)
2-outlets used for
accessories such
as Wi-Fi routers,
teacher laptops, or
printers
Note:Each laptop cart power strip
needs to be plugged into a separate
outlet ('A' or 'B').
Left (A) power
strip outlet &
indicator
Right (B) power
strip outlet &
indicator
15-amp Reset Button
Power Cord
Cycle Switch
0107093XR4 Page 6 of 9
Value Cycle Timer Operation
CAUTION
• Do not use the auxiliary outlets to charge multiple laptops (use the 'A' and 'B' outlets only.)
Auxiliary outlets are for peripheral use only.
• Total equipment load not to exceed 15-amps per power strip.
• For indoor use only. Do not install or store the unit where it will be exposed to weather.
Keep unit dry.
• For added safety, plug the timer into a grounded three-prong receptacle controlled by a GFI
(Ground Fault Interrupter) circuit breaker.
Using Timer:
The timer prevents overload by alternating power betweenboth power strips in the cart, providing charging to multiple laptops during
the day. The power strips plug into the outlets labeled 'A' or 'B'.
The timer control can be adjusted between 15-240 minutes. This is the number of minutes a power strip will be "hot" before the
timer switches to the other power strip. 15 minutes can be used as the default setting, but the time setting will depend on the laptop
size, battery capacity, frequency of laptop use, and the time available for charging between uses. Lower minute settings should be
used if the laptops are being used morefrequently.
• To cycle charge both 'A' and 'B' sides, keep the cycle switch in the middle 'Cycle' position, then set the timer control to the
desired cycling increment. After the Side 'A' time expires, the timer will activate Side “B” for the same period of time and will
continue to cycle until the On/Off switch is set to the "OFF" position.
• To manually-overridethe timer function, and charge side 'A' only, switch the cycle switch from the middle to the 'A' position.
• To manually-overridethe timer function, and charge side 'B' only, switch the cycle switch from the middle to the 'B' position.
Specifications:
• 15-amp, 120 volt, 60Hz (1875 watt max) circuit breaker.
• 15-240 minute timer.
• 20' 14 AWG power cord.
On / Off Switch
(Controls power to timer &
'A' and 'B' outlets)
Timer Control Auxiliary
(constant-power)
2-outlets used for
accessories such
as Wi-Fi routers,
teacher laptops, or
printers
Note:Each laptop cart power strip
needs to be plugged into a separate
outlet ('A' or 'B').
Left (A) power
strip outlet &
indicator
Right (B) power
strip outlet &
indicator
15-amp Reset Button
Power Cord
Cycle Switch

Riser Podium
18"W x 1713/16"D
95002
Replacement Key Set
for 2-pt lock
55142
Tray Edge Trim
applies to shelf pull edge
30-pieces
55172
6-Outlet Power Strip
w/ 12' cord
115/16"W x 11/16"D x 13/16"H
99023
7-Outlet Power Strip, insured
w/surge protector, bracket, and 12' cord
10"W x 2"D x 11/8"H
99024
Flip-up Document Camera/Task Shelf
adjustable-height, mounts on left or right
221/8"W x 183/8"D (150 lbs max load)
55219
Options
0107093XR4 Page 7 of 9
Riser Podium
18"W x 1713/16"D
95002
Data Cord Reel
w/ 14' CAT 5 cord & plugs
99026
Non-Slip Pad
24"W x 17"D
95508
Replacement Key Set
for 2-pt lock
55142
Tray Edge Trim
applies to shelf pull edge
30-pieces
55172
6-Outlet Power Strip
w/ 12' cord
115/16"W x 11/16"D x 13/16"H
99023
7-Outlet Power Strip, insured
w/surge protector, bracket, and 12' cord
10"W x 2"D x 11/8"H
99024
Flip-up Document Camera/Task Shelf
adjustable-height, mounts on left or right
221/8"W x 183/8"D (150 lbs max load)
55219
Options

Technical Specs
Capacity
●Overall dimensions: (See dimensioned drawings)
●Storage and charging capability for up to 30 netbooks/mini-laptops
●Pull-out laptop tray dimensions: 161/2"W x 201/2"D x 21/4"H
●Optional flip-up shelf is 221/8"W x 223/4"D x 1" thick and can support a
maximum of 150 lbs shelf hinges lock into place in the upright position.
●Electrical: The cart has two 16-outlet (125V) power strips, each containing
a 15-amp breaker, on/off switch, and a 12' nominal 14 AWG 3-wire power
cord. Outlets are accessible from the back of the unit.
●Maximum recommended load per tray not to exceed 7 lbs
●Maximum recommended load on work surface not to exceed 100 lbs
●15' retractable 15-amp power cord reel
●The 5" balloon wheels have a weight capacity of 325 lbs each
(1300 lbs max total unit weight)
●Meets or exceeds all ANSI-BIFMA test standards
●Features and specifications subject to change without notice
●Unit weight (nominal): 225 lbs
●Shipping weight (nominal): 266 lbs
Construction
●The work surface is constructed from 11/16" thick industrial-grade composite
board with .030 high-pressure laminate on one face, and a balancing phenolic
backer on the opposing face
●Metal components consist of 16-gauge and 20-gauge steel
●20-gauge steel pull-out laptop trays and side panels
●16-gauge steel doors and corner columns
●Solid wood corner column trim
●Work surface edges are covered with 3mm vinyl
●Ergonomic handle is made of black recycled plastic
●All metal components are finished with a scratch-resistant powder coat epoxy
●Each netLT30 is factory-assembled (except for handle) w/ wheels,
packaged, and shipped on its own skid
55325
net LT-30 Netbook Cart
0107093XR4 Page 8 of 9
To wall outlet
Technical Specs
Capacity
●Overall dimensions: (See dimensioned drawings)
●Storage and charging capability for up to 30 netbooks/mini-laptops
●Pull-out laptop tray dimensions: 161/2"W x 201/2"D x 21/4"H
●Optional flip-up shelf is 221/8"W x 223/4"D x 1" thick and can support a
maximum of 150 lbs shelf hinges lock into place in the upright position.
●Electrical: The cart has two 16-outlet (125V) power strips, each containing
a 15-amp breaker, on/off switch, and a 12' nominal 14 AWG 3-wire power
cord. Outlets are accessible from the back of the unit.
●Maximum recommended load per tray not to exceed 7 lbs
●Maximum recommended load on work surface not to exceed 100 lbs
●15' retractable 15-amp power cord reel
●The 5" balloon wheels have a weight capacity of 325 lbs each
(1300 lbs max total unit weight)
●Meets or exceeds all ANSI-BIFMA test standards
●Features and specifications subject to change without notice
●Unit weight (nominal): 225 lbs
●Shipping weight (nominal): 266 lbs
Construction
●The work surface is constructed from 11/16" thick industrial-grade composite
board with .030 high-pressure laminate on one face, and a balancing phenolic
backer on the opposing face
●Metal components consist of 16-gauge and 20-gauge steel
●20-gauge steel pull-out laptop trays and side panels
●16-gauge steel doors and corner columns
●Solid wood corner column trim
●Work surface edges are covered with 3mm vinyl
●Ergonomic handle is made of black recycled plastic
●All metal components are finished with a scratch-resistant powder coat epoxy
●Each netLT30 is factory-assembled (except for handle) w/ wheels,
packaged, and shipped on its own skid
55325
net LT-30 Netbook Cart
Top view
Left-side view Front view
0107093XR4
Page
8
of
9

Warranty
WE WILL MAKE IT RIGHT FOR YOU!
We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten
years. Any item deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at
Spectrum’s discretion. This warranty applies to all products manufactured and distributed by Spectrum except the products listed below.
DESIGNED FOR INDOOR USE ONLY - Spectrum’s products have been designed and constructed for indoor use only. Moving or using
outdoors, or on excessively rough surfaces, may cause damage to the products and may void the warranty. If an outdoor application is
desired please contact us to discuss potential custom design solutions.
Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available
and each product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet
Customer Expectations).
Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or concerns. Weare
available to answer your calls Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome
via e-mail at: [e-mail].
Items that have a varying warranty include, but are not limited to, the following:
• Adjustable Crank/Electric Desk Legs (1 yr)
• Flat Panel Desk Gas Cylinders (1 yr)
• Adjustable Height Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles (7 yrs)
• Adjustable Height Chair Parts Casters (2 yrs)
• Adjustable Height Chair Upholstery - In-Stock Upholstery (2 yrs)
• Adjustable Height Chair Upholstery - Graded-In Fabrics and C.O.M (no warranty)
• Height Adjustable Columns and Lifts (1 yr)
• General Use Casters (1 yr)
• Electrical – ECA (1 yr)
• Electrical - Power Strips (1 yr)
• Electrical Surge Suppressors (lifetime)
• Electrical - Retractable Power Cords (1 yr)
• Keyboard/Mouse Trays (1 yr)
• Flat Panel Monitor Arm – General Parts (5 yrs)
•
Flat Panel Monitor Arm
–
Gas Cylinders (2 yrs)
0107093XR4 Page 9 of 9
Warranty
WE WILL MAKE IT RIGHT FOR YOU!
We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten
years. Any item deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at
Spectrum’s discretion. This warranty applies to all products manufactured and distributed by Spectrum except the products listed below.
DESIGNED FOR INDOOR USE ONLY - Spectrum’s products have been designed and constructed for indoor use only. Moving or using
outdoors, or on excessively rough surfaces, may cause damage to the products and may void the warranty. If an outdoor application is
desired please contact us to discuss potential custom design solutions.
Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available
and each product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet
Customer Expectations).
Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or concerns. Weare
available to answer your calls Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome
via e-mail at: [e-mail].
Items that have a varying warranty include, but are not limited to, the following:
• Adjustable Crank/Electric Desk Legs (1 yr)
• Flat Panel Desk Gas Cylinders (1 yr)
• Adjustable Height Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles (7 yrs)
• Adjustable Height Chair Parts Casters (2 yrs)
• Adjustable Height Chair Upholstery - In-Stock Upholstery (2 yrs)
• Adjustable Height Chair Upholstery - Graded-In Fabrics and C.O.M (no warranty)
• Height Adjustable Columns and Lifts (1 yr)
• General Use Casters (1 yr)
• Electrical – ECA (1 yr)
• Electrical - Power Strips (1 yr)
• Electrical Surge Suppressors (lifetime)
• Electrical - Retractable Power Cords (1 yr)
• Keyboard/Mouse Trays (1 yr)
• Flat Panel Monitor Arm – General Parts (5 yrs)
• Flat Panel Monitor Arm – Gas Cylinders (2 yrs)
• CRT Monitor Arm (1 yr)
The warranty, as stated above, is effective as of 05/28/2009