Spectrum EGD-24 Supplement




Model Voltage Power (W) Amps Dimensions (inches) Temperatures
Width Depth Height 0C 0F
EGD-24 208/240 V 4200/5600 20.2/23.4A 24" 21.7" 12.9" 65-250C 150-480F
EGD-36 208/240 V 6300/8400W 30/35A 36" 21.8" 12.9" 65-250C 150-480F
BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS
Congratulations on your purchase of SPECTRUM commercial cooking equipment. SPECTRUM takes pride in the design
and quality of our products. When used as intended and with proper care and maintenance, you will experience years of
reliable operation from this equipment. To ensure best results, it is important that you read and follow the instructions in
this manual carefully. It’s important to save these instructions for future reference.
EGD-36
EGD-24
C US LISTED
R
SPECTRUM products have undergone strict product testing in order to comply with regulatory standards
and specications set by international independent, commonwealth and federal authorities.
As testimony to such compliance SPECTRUM products carry the following marks/symbols:

2

Important For Future Reference
Introduction
Congratulations on the purchase of your SPECTRUM machine. Please
take time to carefully read through this manual to ensure the machine
is operated and maintained properly, to ensure the best possible
performance from the product for many years.
SPECTRUM will not accept liability for the following if:
• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the machine.
• Non-original spare parts are used.
• The machine has not been handled and cleaned correctly.
• There is any use damage to the unit.
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or parts, this information is required.
Model Number Serial Number Date Purchased
! !
WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY, OR DEATH. READ THE
INSTALLATION, OPERATION, AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING
OR SERVICING THIS EQUIPMENT.
AVERTISSEMENT: TOUTE INSTALLATION, RÉGLAGE,
MODIFICATION, RÉPARATION OU ENTRETIEN
INCORRECT PEUT OCCASIONNER DES DOMMAGES
MATÉRIELS, DES BLESSURES GRAVES OU LA MORT.
LIRE LES INTRUCTIONS D'INSTALLATION, D'UTILISATION ET
D'ENTRETIEN ATTENTIVEMENT AVANT D'INSTALLER OU DE
RÉPARER CET APPAREIL.
! !
CAUTION: THESE MODELS ARE DESIGNED, BUILT, AND
SOLD FOR COMMERCIAL USE ONLY. IF THESE MODELS
ARE POSITIONED SO THE GENERAL PUBLIC CAN USE
THE EQUIPMENT, MAKE SURE THAT CAUTION SIGNS,
WARNINGS, AND OPERATING INSTRUCTIONS ARE
CLEARLY POSTED NEAR EACH UNIT SO THAT ANYONE
USING THE EQUIPMENT WILL USE IT CORRECTLY AND
NOT INJURE THEMSELVES OR HARM THE EQUIPMENT.
ATTENTION: CES MODÈLES SONT CONÇUS, FABRIQUÉS,
ET VENDUS POUR UN USAGE COMMERCIAL SEULEMENT.
SI CES MODÈLES SONT PLACÉS POUR QUE LE GRAND
PUBLIC PUISSE LES UTILISER, ASSUREZVOUS QUE LES CONSIGNES
D’ATTENTION, D'AVERTISSEMENT, ET LES INSTRUCTIONS
D'UTILISATION SOIENT CLAIREMENT AFFICHÉES PRÈS DE
CHAQUE UNITÉ DE SORTE QUE N'IMPORTE QUEL UTILISATEUR DE
L'APPAREIL L'EMPLOIE CORRECTEMENT ET NE SE BLESSE PAS OU
N'ENDOMMAGE PAS L'APPAREIL.
! !
WARNING: A FACTORY AUTHORIZED SERVICE
PROVIDER SHOULD HANDLE ALL MAINTENANCE
AND REPAIR. BEFORE DOING ANY MAINTENANCE
OR REPAIR, FOLLOW SERVICE SET UP ARRANGEMENT
ON PAGE 11.
AVERTISSEMENT: UN TECHNICIEN AUTORISÉ PAR
L'USINE DEVRA EFFECTUER TOUT L'ENTRETIEN ET LES
RÉPARATIONS. AVANT DE FAIRE TOUT ENTRETIEN OU
RÉPARATION, VEUILLEZ CONTACTER WINCO.
Proper Grounding · Mise à la terre correcte
This machine is provided with a three-pronged
grounding plug. The outlet to which this plug
is connected must be properly grounded. If the
receptacle is not the proper grounding type, contact an
electrician. DO NOT, under any circumstances, cut
or remove the third ground prong from the power cord
or use any adapter plug.
Cette machine est équipée d'une che à trois broches.
La prise sur laquelle cette che est branchée doit être
correctement mise à la terre. Si la prise n'est pas le type de
mise à la terre, contactez avec un électricien. NE PAS, en
aucun cas couper ou enlever la troisième broche de terre à
partir du cordon d'alimentation ou utiliser un adaptateur.
USE A GROUNDED OUTLET
DO NOT ADD AN ADAPTOR
TO THE PLUG
UTILISER UNE PRISE AVEC MISE
À LA TERRE NE PAS AJOUTER UN
ADAPTATEUR SUR LA FICHE

3

Table of Contents
Specications .............................................................................. 1
Warnings ..................................................................................... 2
Introduction ................................................................................ 2
Table of Contents ....................................................................... 3
Packaging .................................................................................... 3
Installation .................................................................................. 4
Operation .................................................................................... 5
Cleaning, Care & Maintenance ................................................. 6
Safety ........................................................................................... 7
Troubleshooting ......................................................................... 7
Service & Repair .......................................................................... 7
Exploded View ........................................................................... 8
Spare Parts List ............................................................................ 9
Electrical Diagram .................................................................... 10
Limited Warranty ......................................................................11
Package Contents
All units come with Installation & Operating Instructions Manual
and the following:
• Griddle
• Catch Tray
SPECTRUM prides itself on quality and service, ensuring that at the
time of packing, all products are supplied fully functional and free
of damage. Should you nd any damage as a result of freight, please
contact your SPECTRUM dealer immediately.
Unpacking the Equipment
DISPOSE OF ALL PACKAGING MATERIALS IN AN
ENVIRONMENTALLY RESPONSIBLE MANNER.
1. Remove all packing materials and tape, as well as any protective
plastic and cardboard, from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.
SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN
PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES
ARENEEDED.
Please keep this manual in a safe place for future use!
NOTE
Please remember that this manual and the warning labels do not replace the need to be alert, to properly train and supervise
operators, and to use common sense when using this equipment.

4
Installation
NOTE
IF CERTIFIED RECEPTACLE IS REQUIRED, IT MUST BE INSTALLED BY
A QUALIFIED ELECTRICIAN WHO IS FAMILIAR WITH ELECTRICAL
PROCEDURES AND CODES. DO NOT ATTEMPT TO WIRE THIS
GRIDDLE YOURSELF.
2. Remove the SPECTRUM Electric Griddle from the packaging. Be
certain that all protective plastics and residues are thoroughly
cleaned from its surface.
3. Place the SPECTRUM Electric Griddle on a rm level surface. Local
standards and regulations should be consulted in order to abide by
standards set in relation to positioning, spacing, and ventilation.
4. Proper connections and power supply are necessary for
satisfactory performance.
5. The external wiring must be in conduit or an approved type of
exible cable suitable for operation at temperature indicated at
the conduit hole, and in a proper size to carry the load.
6. The supply circuit must be correctly fused and equipped with a
means of disconnecting, as required by the local electrical code.
For griddle with plugs and leads set, simply provide a suitable
power point and connect.
THIS EQUIPMENT GETS EXTREMELY HOT.
CAUTION ATTENTION
Do not position or operate near combustible materials or
ammable objects.
Ne pas placer ni faire fonctionner l'appareil près de
matériels combustibles et d'objets inflammables.
Once your Griddle has been placed in position, be sure that the
stainless steel waste tray is correctly positioned.
Une fois que votre Plaque de Cuisson (Plancha) est mise en
place, veillez à ce que le bac à déchets en acier inoxydable
soit correctement placé.
Supply the appropriate power and connect to power source; your
Griddle is now ready to turn on and operate. (For power supply
please see technical specication sheet, page 1).
Fournir l'alimentation secteur appropriée et brancher
l’appareil à la source d'alimentation ; votre plaque
de cuisson est maintenant prête à être allumée et à
fonctionner. (Pour l’alimentation, veuillez voir la fiche
technique, page 1).
FEET
Install feet by screwing each foot into the threaded openings on the
bottom of the griddle. Failure to use feet will void warranty and could
cause unsafe conditions.
LEVELING
Level unit by adjusting the four feet and tighten securely. The adjustable
feet have an adjustment of one inch for lineup with other countertop
lines. Check the feet every 60 days to make sure they are tight.
ASSEMBLY
Take the catch tray and slide into the runners below the heating
elements and place into the rack. Once in position, the catch tray
will catch food product crumbs, grease or drippings.
COMMISSIONING
Commissioning of your new griddle is of the utmost importance.
Commissioning is the thorough and methodical testing of the equipment,
sub systems, and systems to make sure that the nal product functions
properly and safely at the work site. By identifying potential problems
(i.e.: equipment location, ventilation, local re/electrical codes,
installation, operator training and certication) before equipment is
placed into service, costly outages and potential damages can be avoided.
These instructions should be followed at all times. Failure to follow
these instructions could result in injury to yourself and others.
TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:
1. Read this manual thoroughly before installation and operation.
DO NOT proceed with installation and operation if you have any
questions or do not understand anything in this manual. Contact
your representative or the manufacturer rst.
Fire Hazard.
Correct installation precautions,
procedures and regulations
must be followed. Operation
and safety training is necessary
for all users of this equipment.
Risque d'incendie
La surchaue des vapeurs d'huile ou de
l'huile peut s'enammer et provoquer
un incendie. Surveillez la température,
la qualité et le niveau d’huile. Utilisez et
entretenez le système d'élimination des
vapeurs d'huile.
The equipment must be
installed by qualied personnel
only. Correct installation
precautions, procedures and
regulations must be followed
in order to reduce the risk of
re. Hood and re suppression
systems must be maintained
per manufacturer's guidelines.
Only qualied and trained
personnel are to use this
equipment.
Faire chauer l'huile avec précaution. Si
l'huile fume, réduire le feu. Ne pas laisser
l'appareil sans surveillance. Si le feu se
produit, éteindre l'appareil, couvrir jusqu'à
refroidissement. Ne pas mettre l'eau dans
l'huile chaude ou enammée. Ne faites pas
fonctionner avec de l'huile sous la barre
d'huile. L’huile sale a un point d'éclair
plus bas. Remplacer l'huile sur une base
régulière. Maintenir le niveau d'huile
correct. Utiliser un système d'évacuation
de la vapeur d'huile (capot) pour réduire
l'accumulation de graisse et d'huile sur les
surfaces de paroi ou de plafond.
WARNING AVERTISSEMENT
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modied.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modié.
WARNING AVERTISSEMENT

5
Operation
6. Remove the excess fat and wipe clean. Griddle surface is ready
for use.
NOTE
EVEN WITH CAREFUL SEASONING, FOOD CAN STICK TO
THE GRIDDLE COOKING SURFACE UNTIL GRIDDLE PLATE IS
“BROKEN IN”.
Before operating the griddle, it must be checked to see that it
is sitting level. Adjust the feet to level the griddle. Be sure the
catch tray has been assembled correctly (see image below).
Catch Tray
Rack
NOTE
Upon first use, griddle can produce a burning metal smell.
This is normal and smell will decrease with use.
Season the surface
1. Clean griddle surface thoroughly. After griddle has been cleaned, it
must be seasoned to prevent food from sticking. Follow the steps
below for the correct heating method to season the griddle before
use and after scouring.
2. Switch to ON and adjust the thermostat dial knob to 350°F.
3. Use a clean cloth (not a spatula), to spread a thick lm of cooking
oil or fat over the griddle cooking surface. Film must remain on hot
griddle for 30 minutes.
CAUTION
GRIDDLE SURFACE WILL BE HOT
PLAQUE SURFACE SERA CHAUD
4. Remove the excess fat and wipe clean.
5. Apply another lm of cooking oil over hot cooking surface for
another 30 minutes.
Temperature Control
Your griddle should be turned on prior to usage to allow the cooking
surface to warm up; 5-7 minutes is sucient.
To get ecient use from this unit, it is recommended that for
intermittent use that the thermostat be turned down when not
cooking. This will assist in reducing power consumption and also allow
for quicker heat response when needed.
It is recommended that the cooking surface is lightly greased before
each use.
The temperature is thermostatically controlled.
Be sure On/Off switch is ON, for EDG-36, and adjust
temperature dial knob to the desired setting.
Power for EDG-24 is activated when temperature dial knob
is turned to desired heat setting.
The set point of each thermostat is marked on the front panel with
"TEMP " in the 9 o’clock position. Griddle is equipped with one
thermostat per various cooking surface segments.
For the 24” griddle, every 12” and for the 36” griddle, every 18”.
Cooking
Switch griddle to ON and adjust the thermostat dial knob to the
desired temperature. After a short pre-heating period, the thermostat
will automatically maintain the selected temperature. When the set
temperature is reached, the signal light will go OFF.
A temperature setting of between 375ºF and 430ºF will be sucient
for general cooking. This may vary for particular food types, individual
needs, or experience.
Simply place the food products on the grilling surface and cook to
manufacturer's specications.
TO AVOID SERIOUS PERSONAL INJURY:
• ALWAYS install equipment in an area with adequate light and space.
• ONLY operate on a solid, level, nonskid surface that is
nonammable and away from sinks and water hazards.
• NEVER bypass, alter or modify this equipment in any way from
its original condition. Doing so can create hazards and will
void warranty.
• NEVER operate the griddle without all warnings attached to it. Burn Hazard.
When in operation, the
Conveyor Toaster will be hot at
the entrance to the conveyor
cavity.
Please take extreme caution.
Risque de brûlure.
Ne touchez pas les surfaces chaudes ou
chauées liguid tout appareil chaue ou
en fonctionnement.
USE CAUTION WHEN
TOUCHING THE UNIT.
Ne touchez pas le liquide chaud
ou les surfaces de chauage
lorsque l’appareil chaue ou en
fonctionnement.
WARNING AVERTISSEMENT
HOT

6
To maintain the appearance and increase the service
life, clean your unit daily. The Electric Griddle should be
cleaned after each day’s operation; however, the unit may
require more frequent cleaning depending on the volume
of production.
Cleaning, Care & Maintenance
1. Switch power o and disconnect from the outlet before cleaning.
2. Allow the Electric Griddle to cool down after use before dismantling
for cleaning; the unit will still be too hot to handle immediately
after use. Regular cleaning will result in easier cleaning, as the build
up will be less. Correct preparation of the cooking surface when rst
used will assist in keeping the plates clean.
3. For best results clean the plate while still warm using warm soapy
water. A nylon cleaning cloth may be used. It is recommended that
you avoid scrapers made from steel wool, as they will damage the
plate. Do not use cold water on warm plates, as buckling eect
may occur.
4. When scrubbing the plates, do not clean too thoroughly; if you do,
you must prepare the cooking surface again before use.
5. Remove catch tray from unit and discard waste; clean with hot
soapy water.
6. The remainder of the Electric Griddle can be cleaned with a
damp cloth using warm, soapy water. Warm, soapy water is
recommended for cleaning; prolonged use of cleaning agents may
cause damage to stainless steel.
7. Do not immerse completely in water or use hose to clean.
RECOMMENDED CLEANING
It takes very little time and eort to keep the griddle attractive and performing at top eciency. If grease is allowed to accumulate, it will form a
gummy cake and then carbonize into a hard substance that is extremely dicult to remove. To prevent this condition, please follow the cleaning
steps below:
PART REQUIRED ACTION FREQUENCY
Scraping Scrape the griddle with a scraper or exible spatula to remove excess fat and food. A catch tray is provided
for the scrappings.
If there is an accumulation of burned fat and food, griddle must be thoroughly scoured and re-seasoned.
While the griddle is warm, use pumice or griddle stone to remove excess fat and food. Do not use steel
wool because of the danger of steel slivers getting into the food.
After Each Use
Body Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of griddle.
Wipe the polished areas with a soft cloth.
Daily
Controls Griddle must be turned OFF when not in use.
Switch griddle to OFF to disconnect power supply from griddle.
Use a clean cloth to wipe down switches and thermostat dial knobs.
Daily
Catch tray Once griddle has cooled, remove catch tray from griddle and discard the waste, debris and crumbs.
CAUTION: If catch tray is permitted to ll too high, the excess grease will run out of the overow hole at
the front of catch tray.
The catch tray is removed by pulling forward. USE CAUTION WHEN FILLED WITH HOT GREASE!
Per Use
or at least Daily
Burn Hazard.
When in operation, the
Conveyor Toaster will be hot at
the entrance to the conveyor
cavity.
Please take extreme caution.
Risque de brûlure.
Ne touchez pas les surfaces chaudes ou
chauées liguid tout appareil chaue ou
en fonctionnement.
USE CAUTION WHEN
TOUCHING THE UNIT.
Ne touchez pas le liquide chaud
ou les surfaces de chauage
lorsque l’appareil chaue ou en
fonctionnement.
WARNING AVERTISSEMENT
HOT
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modied.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modié.
WARNING AVERTISSEMENT

7
If your SPECTRUM Electric Griddle does not operate, please check the following before placing a service call.
Please ensure:
• There is correct power supply.
• Breaker is checked.
• The machine is plugged in correctly and power is switched on.
• The timer and thermostat are in the correct position.
• The elements are clear of any food particles.
Troubleshooting
ISSUE MIGHT BE CAUSED BY RECOMMENDED SOLUTION
The unit is not working
Power supply Check power source
Power switch has not been turned on Check that the unit is correctly plugged in and
turned on
Plug/cord, set or external wiring is damaged Call WINCO to make service arrangements through
its Service Provider Network
Internal wiring fault Call WINCO to make service arrangements through
its Service Provider Network
The indicator light is on, but
griddle is not heating up
Faulty elements Call WINCO to make service arrangements through
its Service Provider Network
Operation of thermostat
All thermostats are not turned on
Make sure thermostat is set correctly and make sure
dial is not spinning on the thermostat, giving the
wrong reading
Faulty thermostat Call WINCO to make service arrangements through
its Service Provider Network
The indicator light is NOT on, but
the griddle IS heating up
Faulty indicator light Call WINCO to make service arrangements through
its Service Provider Network
Cooking Surface is heating up
slowly
Carbon build up Make sure that the plates are kept clean and free
from carbon build up/debris
Thermostat setting Make sure thermostat is set correctly and make sure
dial is not spinning on the thermostat, giving the
wrong reading
Faulty elements Call WINCO to make service arrangements through
its Service Provider Network
Food Sticking
Carbon build up Make sure that the plates are kept clean and free
from carbon build up/debris
Not seasoned Season grill, see Operating Instructions, page 5
Service and Repair
There are no user serviceable parts within this appliance.
To avoid serious injury or damage, never attempt to repair the unit
or replace a damaged power cord yourself.
DO NOT send unit to WINCO without rst contacting our customer
service department.
See "Limited Warranty" section on page 11 for details.
Safety
A WINCO Approved Service Technician should carry out repairs if
necessary. Do not remove any components or service panels on this
product. Allow the griddle to cool down after use before dismantling
for cleaning; the unit will be too hot to handle immediately after use.
Switch o power and disconnect from the outlet before cleaning.
Do not immerse unit in water or use hose to clean.
Ne pas immerger l'appareil dans l'eau ni utilisez un jet d'eau pour
le nettoyer.
If the power cord is damaged, it must be replaced by a WINCO
Approved Qualied Service Technician in order to avoid a hazard.

8
Exploded View & Spare Parts List
MODEL EGD36
Model EGD-36
No. Description Part # QTY
1 Griddle Plates Assy EGD-36-P1 1
2 Heating Element EGD-36-P2 2
3 Hardware Assembly EGD-36-P3 2
4 Insulation EGD-36-P4 2
5 Insulation Plates EGD-36-P5 1
6
Ceramic
Connector - 1
EGD-36-P6 2
Ceramic
Connector - 2
EGD-36-P7 2
7 Plug & Lead EGD-36-P8 1
8 Feet EGD-36-P9 4
9 Base Board EGD-36-P10 1
10 Thermostat EGD-36-P11 2
11 Dial EGD-36-P12 2
12 Indicator Light EGD-36-P13 2
13 On/O Switch EGD-36-P14 2
14 Drip Tray EGD-36-P15 1
15 Main Body Assy EGD-36-P16 1

9
Exploded View & Spare Parts List
Model EGD-24
No. Description Part # QTY
1 Feet EGD-24-P1 1
2 Set Square EGD-24-P2 2
3 Drip Tray EGD-24-P3 2
4 Base Board EGD-24-P4 1
5 Indicator Light EGD-24-P5 1
6 Dial EGD-24-P6 4
7 On/O Switch EGD-24-P7 1
8 Thermostat EGD-24-P8 4
9 Main Body Assy EGD-24-P9 1
10 Insulation Plates EGD-24-P10 2
11 Insulation EGD-24-P11 2
12 Hardware Assembly EGD-24-P12 2
13 Heating Element EGD-24-P13 2
14 Griddle Plates Assy EGD-24-P14 1
15 Plug & Lead EGD-24-P15 2
16 Connection Box EGD-24-P16 2
17 Connector Bar EGD-24-P17 2
18 Connection
Box Cover
EGD-24-P18 1
MODEL EGD24

10
NOTE:
1) FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY,
SUITABLE FOR AT LEAST 194°F (90°C). USE WIRE GAUGE
SHOWN OR LARGER
2) ALL INTERNAL WIRING IS #14 GA
SINGLE PHASE CONNECTION
3 PHASE CONNECTION
THERMOSTAT 2THERMOSTAT 1
PILOT LIGHT 1 PILOT LIGHT 2
ON/OFF SWITCH 1
ON/OFF SWITCH 1
3 PHASE CONNECTION
SINGLE PHASE CONNECTION
ON/OFF SWITCH 2
ON/OFF SWITCH 3
ON/OFF SWITCH 2
HEATING ELEMENTS 1 HEATING ELEMENTS 2
THERMOSTAT 2 THERMOSTAT 3THERMOSTAT 1
PILOT LIGHT 2 PILOT LIGHT 3PILOT LIGHT 1
HEATING ELEMENTS 1 HEATING ELEMENTS 2 HEATING ELEMENTS 3
NOTE:
1) FOR SUPPLY CONNECTIONS USE COPPER WIRE ONLY,
SUITABLE FOR AT LEAST 194°F (90°C). USE WIRE GAUGE
SHOWN OR LARGER
2) ALL INTERNAL WIRING IS #14 GA
Electrical Diagram The circuit diagrams are provided to assist qualied technicians. Only SPECTRUM agents or Recommended Qualied Technicians
should carry out repairs if needed. (Refer to page 11 for service arrangements)
DO NOT remove any components or service panels on this product.
EGD-24
EGD-36

11
WINCO warrants to the original purchaser of new equipment that said
equipment, when installed in accordance with our instructions within
North America and subjected to normal use, is free from defects in
material or workmanship for a period of 1 year. The labor warranty is
one year from original installation or 18 months from actual factory
shipment date, whichever date occurs rst. Warranty includes on site
service calls within 60 miles of an authorized service company. End user
is responsible for all extra travel and mileage at prevailing rates.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY DISCLAIMS
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED
OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY
IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING
EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR
WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.
All repairs pursuant to this Warranty will be performed by an
Authorized Designated WINCO Service Location during normal working
hours. This warranty does not cover services performed at overtime or
premium labor rates. End user is responsible for the dierence between
normal service rates and premium service rates.
IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY,
INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY,
PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER
ECONOMIC LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES,
WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR
OTHERWISE.
This warranty is given only to the rst purchaser from a retail dealer.
No warranty is given to subsequent transferees.
Warranty does not cover product failures caused by: failure to maintain,
neglect, abuse, damage due to excess water, re, normal wear,
improper set up and use. Periodic maintenance is not covered.
This warranty is not in force until such time as a properly completed
and digitally signed Installation/Warranty Registration has been
received by WINCO within 30 days from the date of installation.
WARRANTY SERVICE
To initiate warranty service contact: [e-mail]
or call: 973-295-3899
DO NOT send unit to WINCO without rst contacting our customer
service department.
REGISTER ONLINE AT:
http://support.wincous.com
Limited Warranty
Proof of purchase is required to extend warranty more than 1 year from
date of shipment from the factory.
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND
EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. WINCO
NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME
FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION
WITH SAID EQUIPMENT.
Examples of items not covered under warranty, but not limited to just
these items:
1. Acts of God, re, water damage, burglary, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after market parts.
5. Repairs made by anyone other than a WINCO designated
service provider.
6. Lubrication.
7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
8. Cleaning of equipment.
9. Misuse or abuse.
WARRANTY REGISTRATION
SCAN THE QR CODE WITH YOUR MOBILE DEVICE
or go to
http://support.wincous.com
TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.