Spectrum 37130 User manual

0118583R6 Page 1 of 4
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Display Stand
37130
(1) 0192849
VESA mount
(4) 0108896
1/4-20 Flanged
serrated locknut
(12) 052605
1/4-20 x 15mm
JC bolt
(1) 0118193
End cap 3” x 3”
(1) 0118510
Upright assembly
(1) 0131924
Upright bracket
Figure 1
Rubber thread
protectors
Bottom of upright
assembly
(1) 025039
4mm Hex wrench
1. With the upright assembly upside-down, remove the rubber
thread protector from each threaded stud. Figure 1.
󰀨
Installation

”
4mm

0118583R6 Page 2 of 4
Figure 2.1
Figure 3
Upright
assembly
Worksurface
1/4-20 Flanged
serrated locknut
(4 required)
Mounting holes and cutout needed

2. Be sure the worksurface being used has the cutout / hole pattern
shown in Figure 2.1, or Figure 2.2.
Figure 2.2
Optio Tables
InVision / Element / Nano Tables
3. An unattached worksurface will facilitate installation of the display
stand fasteners. If attached, remove the worksurface fasteners
securing it to the base and slide the worksurface 6” over the base to
provide access to the display stand mounting holes. Figure 3.
4. Align the studs and insert the upright into the worksurface mounting holes.
5. With a second person holding the upright, Install (4) 1/4-20 Flanged
serrated locknuts and tighten securely.
Note: For InVision Nano table installation,
see p.4 for special instructions.
Pull worksurface
out about 6” to ac-
cess display stand
mounting holes

0118583R6 Page 3 of 4
Figure 4
Upright bracket
Upright
assembly
1/4-20 x 15mm JC
bolts (4 required)
End cap
Figure 5
Upright opening
Monitor
mounting plate
1/4-20 x 15mm
JC bolts
(4 required)
6. Attach the upright bracket to the upright assembly as shown using
(4) 1/4-20 x 15mm JC bolts and tighten securely. (Multiple mounting
holes / height positions are available on the upright assembly).
Figure 4.
1. Refer to the instructions included with the monitor mount for complete
monitor installation procedure.
2. Install the monitor mounting plate to the upright bracket with (4) 1/4-
20 x 15mm JC bolts and tighten securely. Figure 5.
3. Install monitor and route wiring through the upright opening.
4. Install end cap on top of upright.
• Refer to the instructions included with the monitor mount for
complete monitor and security rod installation procedure.
• The assembled display stand accommodates most 37”-70”
monitors.
• Be sure your monitor does not exceed the weight capacity of 125 lb.
Install monitor
WARNING
The monitor should always be removed
from the stand before moving the unit.
Hanging rail

InVision Nano Table Installation only
0118583R6 Page 4 of 4
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
Warranty
1-800-235-1262
Toll-free HELPLINE
[email protected]
© 2022 Spectrum Industries Inc., All rights reserved.
We will make it right for you!
Thanks for choosing Spectrum! Spectrum is committed to provide complete customer satisfaction.
Each of our products is manufactured from the best materials available and each product is strin-
gently monitored throughout the production process through our P.A.C.E. program (Product Assur-
ance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from
defect for the period set out in the warranty from the date of delivery.
For a listing of all product specifi c warranty terms please visit our website at:
https://www.spectrumfurniture.com/en/resources/purchasing-terms-warranty
1. Remove the (4) screws shown. Figure 6.1.
2. Remove end panel.
Figure 6.1
End panel
Remove these screws
Remove these
screws
Note: To install the Display Stand on a Nano table,
the end panel must be removed prior to installing.
1/4-20 Flanged
serrated locknut
(4 required)
3. Align the studs and insert the upright into the worksurface
mounting holes.
4. With a second person holding the upright, install the (2) inner
1/4-20 Flanged serrated locknuts. Figure 6.2.
5. Replace the end panel.
6. 
7. Tighten all locknuts securely.
Figure 6.2
Upright assembly