Speed Queen On-Premises UD08F055 User manual

On-Premises
Heated Roll Flatwork Finisher
A Passion to Lead
200 mm roll (8")
325 mm roll (13")
500 mm roll (20")

Low Maintenance
The heated roll requires no waxing when
used on a daily basis.This is an
innovation that separates us
from the competition.
A significant difference in
Speed Queen’s innovation is the
permanently lubricated bearings on
the 200 mm (8") and 325 mm (13")
heated roll finishers.This can save hours
of maintenance every month, while
keeping your machine operating like it
just came from the factory.
Another unique advantage of
Speed Queen is the finished goods
fingers.To ensure the linens remove themselves from
the heated roll without wrapping around the roll,
Speed Queen installs a row of fingers to keep your
finisher running without destroying linens.
Energy Efficient
Our low kW consumption ratings will save you
money.We achieve a low kW consumption through
numerous details that make our flatwork finisher more
energy friendly.To maintain the heat on the steel roll
which presses the linen, we use thicker steel for a
more consistent temperature.
While the heat is produced near the top of the unit,
we place our dual exhaust fans toward the bottom to
remove less heat from the roll. In combination with
this, we totally enclose the entire cabinet to maintain
more insulation around the heated roll. Our 300º
angle of contact gives linens a longer contact with the
heated roll, allowing less energy to be consumed.
Control
The micro control allows for pre-sets of
temperature and speed settings.The
temperature range is 80º C to 176.6º
C.There are seven speed settings to
assist in getting the precise speed for
the linen type and moisture content.
When finished at the end of a day, simply press the
STOP button and the control will allow the roll to
continue to turn until it reaches a safe temperature
of 80º C before the roll completely stops.
When you start the day, the control turns the roll at
the lowest speed until it reaches 80º C to allow for
more efficient energy use.
Selecting the Proper Size
While our units are available with 200, 325 or 500 mm
(8", 13" or 20") diameter rolls, selecting the proper size
will make the job easier.The larger the diameter of the
roll, the faster the operating speed since the linen is in
more contact with the heated surface.
The ironer’s finishing length should be slightly larger
than the width of the linen you will finish. Most linens
for tables of four will require a 1600 mm (63") width.
If finishing sheets or banquet tablecloths, you may
require a 3200 mm (126") width. Side Views
Finished Goods
Fingers

Safety Features
Your safety is of great concern when designing our
products. A stop bar is designed to protect an opera-
tor from placing their hands too far into the machine.
Our control provides numerous alarms to indicate
when certain machine components are not working
properly.These alarms include, airflow safety, thermal
motor warnings, speed regulator, ignition alarm and an
overheating alarm.
If the machine’s power is interrupted when a linen is
being processed, the linen must be removed or it risks
damage.We provide a manual crank to easily remove
the linen before it is damaged.
Details Make the Difference
Through our demands for innovation to assist our cus-
tomers, Speed Queen offers user friendly items such
as the feeding tray to assist in feeding napkins or longer
items.
Our no-staple, nomex, feed ribbons are designed
to last longer and always look good.
Our return ribbons, which are connected with staples,
are covered with nomex to protect your linens from
damage from the staples as they get worn.
The slanted return trough is more user-friendly
than a flat return table where finished goods often get
wrinkles prior to the operator removing them from the
finisher.
The finished goods fingers are just another of
the innovative details you get with Speed Queen
flatwork finishers.
The compact design allows for the unit to be installed
just 49 mm (two inches) from the back wall.
Warranty
Speed Queen’s commitment to customers comes with
an industry-leading warranty, which starts with a one-
year* limited parts warranty. To us, building the best
machines on the market doesn’t mean much if we’re
not willing to also take the lead in standing behind them.
As a Speed Queen customer, you’ll never have to worry
about our bond.
* Parts only, labor not included. See Speed Queen Warranty Bond for specifics.

www.speedqueen.com
AI11-0733
OPL Heated Roll Flatwork Finisher Specifications
* Removal of trays will allow 800 mm (32") door access on all models.
** One motor on electric models. Electric heated models not available in Canada.
*** One motor on steam models.
Due to continuous product improvements, design and specifications subject to change without notice.
For further details on installation, refer to the Installation, Operation and Maintenance Instructions supplied with the ironer.
©Copyright 2010 Alliance Laundry Systems LLC
UD08F055 UD13F063 UD13F079 UD13F126 UD20F075 UD20F098 UD20F126
Roll Diameter - mm (in) 200 (8") 325 (13") 325 (13") 325 (13") 500 (20") 500 (20") 500 (20")
Finishing Width - mm (in) 1400 (55") 1600 (63") 2000 (79") 3200 (126") 1900 (75") 2500 (98") 3200 (126")
Ironing Speed - m/m (ft/m) 1-4.5 (3-15) 1-9 (3-30) 1-9 (3-30) 1-9 (3-30) 1-9 (3-30) 1-9 (3-30) 1-9 (3-30)
Width - mm (in) 1880 (74") 2192 (86") 2542 (100 1/8") 3910 (154") 2975 (117 1/8") 3574 (140 3/4") 4275 (168 5/16")
Depth - mm (in) 445 (17 1/2") 661 (26") 661 (26") 860 (34") 1072 (42 3/16") 1072 (42 1/4") 1072 (42 1/4")
Height - mm (in) 1335 (52 1/2") 1113 (43 13/16") 1113 (43 13/16") 1113 (44") 1171 (46 1/8") 1171 (46 1/8") 1171 (46 1/8")
Roll Motor - kW (HP) .25 (.33) .25 (.33) .25 (.33) .25 (.33) .37 (.5) .37 (.5) .37 (.5)
Roll Exhaust Motor - kW (HP) .09 (1 x .12) 2 x .12** (2 x .16**) 2 x .12 (2 x .16) 2 x .12 (2 x .16) 2 x .25*** (2 x .34***) 2 x .25 (2 x .34) 2 x .25 (2 x .34)
Roll Exhaust Duct - mm (in) 83 (1 x 3 1/4") 2 x 98** (2 x 4"**) 2 x 98 (2 x 4") 2 x 98 (2 x 4") 2 x 150*** (2 x 6"***) 2 x 150 (2 x 6") 2 x 150 (2 x 6")
Gas Heating
Maximum Gas Input - N/A 23 (76,792) 30 (102,340) 40 (136,000) 40 (136,453) 55 (187,623) 69 (235,495)
kW (Btu)
Gas Inlet - mm (in) N/A 14 (3/4") 14 (3/4") 14 (3/4") 22 (1") 22 (1") 22 (1")
Electrical Requirements N/A 120/60/1 • 15 120/60/1 • 15 120/60/1 • 15 120/60/1 • 15 120/60/1 • 15 120/60/1 • 15
• Circuit Breaker N/A 230/50/3 • 6 230/50/3 • 6 230/50/3 • 6 230/50/3 • 6 230/50/3 • 6 230/50/3 • 6
N/A 400/50/3 • 6 400/50/3 • 6 400/50/3 • 6 400/50/3 • 6 400/50/3 • 6 400/50/3 • 6
Electric Heating
Capacity Resistances - 10.5 (14) 16 (21) 20 (27) N/A 31.5 (42) 40.5 (54) 54 (72)
kW (HP)
Electrical Requirements 208-240/60/3 • 40 208-240/60/3 • 50 208-240/60/3 • 63 N/A 208-240/60/3 • 100 208-240/60/3 • 125 208-240/60/3 • 163
• Circuit Breaker 230/50/3 • 40 230/50/3 • 50 230/50/3 • 63 N/A 230/50/3 • 100 230/50/3 • 125 230/50/3 • 163
400/50/3 • 25 400/50/3 • 32 400/50/3 • 40 N/A 400/50/3 • 63 400/50/3 • 63 400/50/3 • 100
Steam Heating
Steam Inlet - mm (in) N/A N/A N/A N/A 19.5 (3/4") 19.5 (3/4") 19.5 (3/4")
Condensate Return - N/A N/A N/A N/A 12.7 (1/2") 12.7 (1/2") 12.7 (1/2")
mm (in)
Hourly Consumption - N/A N/A N/A N/A 50 (110) 67 (147) 85 (187)
kg/hr (lb/hr)
Min.-Max. Steam Pressure - N/A N/A N/A N/A 10 (145) 10 (145) 10 (145)
bar (psi)
Electrical Requirements N/A N/A N/A N/A 120/60/1 • 15 120/60/1 • 15 120/60/1 • 15
• Circuit Breaker N/A N/A N/A N/A 230/50/3 • 4 230/50/3 • 4 230/50/3 • 4
N/A N/A N/A N/A 400/50/3 • 4 400/50/3 • 4 400/50/3 • 4
Shipping Weight - kg (lb) 190 (418) 599 (1320) 669 (1474) 950 (2095) 984 (2167) 1269 (2796) 1553 (3421)
Approvals ETL, CE CSA, ETL, CE CSA, ETL, CE CSA, ETL, CE CSA, ETL, CE CSA, ETL, CE CSA, ETL, CE