SpinCore Technologies RadioProcessor USB Power Supply User manual
RadioProcessor™USB
Power Supply
Owner’s Manual
RadioProcessor™USB Power
Supply
Congratulations and thank you for choosing a design from
SpinCore Technologies, Inc.
We appreciate your business
At SpinCore, we try to fully support the needs of our customers. If you
are in need of assistance, please contact us and we will strive to provide
the necessary support.
© 2007 - 2020 SpinCore Technologies, Inc. All rights reserved.
SpinCore Technologies, Inc. reserves the right to make changes to the product s) or information herein without notice.
RadioProcessor™, PulseBlaster™, SpinCore, and the SpinCore Technologies, Inc. logos are trademarks of SpinCore Technologies, Inc.
All other trademarks are the property of their respective owners.
SpinCore Technologies, Inc. makes every effort to verify the correct operation of the equipment. This equipment version is not
intended for use in a system in which the failure of a SpinCore device will threaten the safety of equipment or person s).
2020-01-15 2
www.spincore.com
RadioProcessor™USB Power
Supply
Table of Contents
I. Overview ................................................................................................ 4
II. Connector Information ......................................................................... 5
Input Connector ............................................................................................................. 5
Output Connector .......................................................................................................... 5
Cable Information .......................................................................................................... 6
III. Contact Information ............................................................................ 7
2020-01-15 3
www.spincore.com
RadioProcessor™USB Power
Supply
I. Overview
The RadioProcessorTMUSB Power Supply generates +5V/2A, +6V/1A and -6V/0.2A output
voltages with a low ripple factor as required by the RadioProcessorTM USB board. The
RadioProcessorTMUSB Power Supply can operate under two different configurations depending on
the input power sources:
1.Single input of 12V for triple DC/DC conversion:
In this configuration, the RadioProcessorTMUSB Power Supply converts the 12 V input voltage into
three regulated 5V/2A, +6V/1A and -6V/0.2A output voltages. The RadioProcessorTMUSB Power
Supply has a wide input voltage range of 7.5 V-16 V in this configuration. This is the standard
model and is suitable for most applications.
2.Dual input of 12V and 5V for dual DC/DC conversion:
In this configuration, the RadioProcessorTMUSB Power Supply converts the +12 V input voltage
into +6V/1A and -6V/0.2A output voltages and takes 5V/2A directly from the +5 V input source.
Please specify if you have dual inputs available and would prefer this model, SpinCore will be glad
to provide.
The DC/DC voltage conversion circuit design utilizes switch-mode technology to achieve high
power conversion efficiency and thus decreasing the operating temperature.
The 4-pin input connector is compatible with standard 12 V and 5 V PC power supply
connectors. The 6-pin output connector is pin-compatible with the power connector of
RadioProcessorUSB boards, facilitating a simple 1:1 cable connection between boards.
The physical size of the board is approximately 5 cm by 10 cm.
2020-01-15 4
www.spincore.com
RadioProcessor™USB Power
Supply
II. Connector Information
Input Connector
The RadioProcessor-USB™ Power Supply has one 4-pin input connector. The pin and signal
arrangements for this connector are shown below in Figure 1.
Figure 1: 4-Pin Input Connector
Part number: 53109-0410 Mouser 538-531-09-0410)
Output Connector
The RadioProcessor-USB™ Power Supply has one 6-pin output connector. The pin and signal
arrangements for this connector are shown below in Figure 2.
Figure 2: 6-pin Output Connector
Part number: 39-28-8060 Digi-Key WM23802-ND)
2020-01-15 5
www.spincore.com
RadioProcessor™USB Power
Supply
Cable Information
If you will be making your own power supply cable to connect to the 6-pin output connector, you
will need the following parts or their equivalents: One 6-pin female Mini-Fit Jr. TM connector DigiKey
part No. WM23702-ND) and six Mini Fit Jr. TM crimp receptacles Digikey part No. WM2501-ND).
2020-01-15 6
www.spincore.com
Table of contents
Other SpinCore Technologies Power Supply manuals
