Spire 860-0032 Product information sheet

FOR OUTDOOR USE ONLY.
NOT FOR COMMERCIAL USE.
POUR USAGE EXTÉRIEUR SEULEMENT.
PAS À DES FINS COMMERCIALES.
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
IMPORTANT, À CONSERVER POUR DE FUTURS BESOINS DE RÉFÉRENCE: À LIRE SOIGNEUSEMENT.
FREESTANDING OUTDOOR ISLAND GRILL
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service,
call: 1-833-55S-PIRE / 1-833-557-7473
Languages spoken: English, Spanish, French 8 a.m.-5 p.m., PST. Monday-Friday.
PIED EXTÉRIEUR ISLAND GRILL
Instructions d’installation et Guide d’utilisation et d’entretien
Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, des accessoires ou du service,
composer le: 1-833-55S-PIRE / 1-833-557-7473
Langues parlées: anglais , espagnol, français entre 8 h et 17 h, HNP, du lundi au vendredi.
860-0032 (LP) /870-0032 (NG)
19000998A1

2
TABLE OF CONTENTS
OUTDOOR GRILL SAFETY………………….……..…………3
INSTALLATION REQUIREMENTS……………………………..5
Location Requirements………………………………………...…5
Product Dimensions………………………………..……….…….6
Gas Supply Requirements…………………..…..……………..…7
Gas Connection Requirements…………………..…..………..…7
Package Parts List ……..…………………..…..……………..…9
Tools and Hardware ..……………………………...……….…10
ASSEMBLY INSTRUCTIONS……………..............…...11
Gas Connection ...…………………….............……………20
GAS CONVERSIONS……………….................................…...21
Tools and Parts for Gas Conversion ……....………………...21
Conversion from LP Gas to Natural Gas…....………………...22
Gas Connection ..…...……………….............……………24
Check and Adjust the Burners ………..………….………….…25
OUTDOOR GRILL USE ………………….………………..…27
Using Your Outdoor Grill ……………………….…………….…27
Using Your Rear Burner .…….…………………………..……29
TIPS FOR OUTDOOR GRILLING ……………..……………...30
Cooking Methods ………………….…………………………….30
OUTDOOR GRILL CARE ………………………………...……31
Replacing the Igniter Battery …….…………………..……....31
General Cleaning ……………………………………….….....…31
TROUBLESHOOTING ...........................................................33
ASSISTANCE …………………………………………….…..…33
Accessories………………………………………………...……..33
WARRANTY ……………………………………….…………….34
REPLACEMENT PARTS………………………………...….…69
TABLE DES MATIÈRES
SÉCURITÉ DU GRIL D'EXTÉRIEUR….………..…….…….…36
EXIGENCES D’INSTALLATION…….……………..….....….38
Exigences d'emplacement…………….….………....….………38
Dimensions du produit ……………………………………...…..39
Spécifications de l'alimentation en gaz………………..………40
Exigences concernant le raccordement au gaz………………41
Liste des pièces de l'emballage ………………..………………42
Outils et quincaillerie .………….……..………........…..………43
INSTRUCTIONS DE MONTAGE……………....................44
Raccordement au gaz………………………………….….….…53
CONVERSIONS POUR CHANGEMENT DE GAZ ……...…..54
Outils et pièces pour conversion de gaz ………….………....54
Conversion de propane àgaz naturel ……………….…...…...55
Raccordement au gaz …………………………............…....….57
Contrôle et réglage des brûleurs ………………………….…...59
UTILISATION DU GRIL D’EXTÉRIEUR …….………..……...60
Utilisation de votre gril d'extérieur….….……….……..……….60
Utilisation de votre brûleur arrière…………..……..……...62
CONSEILS POUR L'UTILISATION DU GRIL
D’EXTÉRIEUR………….…………..…...….……......…...……..63
Méthodes de cuisson….………………..……….…...……….…63
ENTRETIEN DU GRIL D’EXTÉRIEUR …………..…………...64
Remplacement de la pile de l’allumeur ……..…...………….64
Nettoage général ………………………………...……….…….64
DÉPANNAGE..........................................................................66
ASSISTANCE………………………………….…..………….…66
Accessoires………………………………………………...……..66
GARANTIE……………………………………..……..……...…..67
PIÈCES DE RECHANGE …………………..………………...69
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from
the appliance and immediately call
your gas supplier or your fire
department.
WARNING
1. Do not store or use gasoline or
other flammable liquids or vapors in
the vicinity of this or any other
appliance.
2. An LP cylinder not connected for
use shall not be stored in the
vicinity of this or any other
appliance.

OUTDOOR GRILL SAFETY
3
IMPORTANT: This grill is manufactured for outdoor use only. See “Gas Supply Requirements” section. It is the responsibility of the
installer to comply with the minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate
for freestanding models can be found on the left-hand cabinet door.
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.
CALIFORNIA RESIDENTS ONLY -WARNING:
This product and the fuels used to operate this product (liquid propane), and the products of
combustion of such fuels, can expose you to chemicals including benzene, which is known
to the State of California to cause cancer and reproductive harm.
For more information, go to: www.P65Warnings.ca.gov.
WARNING
ELECTRICAL GROUNDING INSTRUCTIONS for Transformer -This appliance is equipped with a plug and should be
plugged directly into a properly grounded receptacle. When installed, must be electrically grounded in accordance with
local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical
Code, CSA C22.1 DO NOT cut or remove the grounding prong from this plug.

IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
Injury to persons, or damage when using the outdoor cooking
gas appliance, follow basic precautions, including the following:
Do not install portable or built-in outdoor cooking gas
appliances in or on a recreational vehicle, portable trailer,
boat or in any other moving installation.
Always maintain minimum clearances from combustible
construction, see “Location Requirements” section.
The outdoor cooking gas appliance shall not be located
under overhead unprotected combustible construction.
This outdoor cooking gas appliance shall be used only
outdoors and shall not be used in a building, garage, or
any other enclosed area.
Keep any electrical supply cord and fuel supply hose away
from any heated surfaces.
Keep outdoor cooking gas appliance area clear and free
from combustible material, gasoline and other flammable
vapors and liquids.
Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation openings of the cylinder enclosure
free and clear from debris.
Open the cabinet door and inspect the gas cylinder supply
hose before each use of the outdoor cooking gas
appliance. If the hose shows excessive abrasion or wear,
or is cut, it MUST be replaced before using the outdoor
cooking gas appliance. Contact your dealer and use only
replacement hoses specified for use with the outdoor
cooking gas appliance.
Visually check the burner flames.
They should be blue. Slight
yellow tipping is normal for
LP gas. The flames should
be approximately 1" (2.5 cm) high.
Check and clean burner/venturi tube for insects and insect
nest. A clogged tube can lead to fire under the outdoor
cooking gas appliance.
The LP gas supply cylinder to be used must be:
-constructed and marked in accordance with the
Specification for LP Gas cylinders of the U.S.
Department of Transportation (DOT) or the National
Standard of Canada, CAN/CSA-b339, Cylinders,
Spheres, and Tubes for Transportation of Dangerous
Goods and Commission.
-provided with a listed overfilling prevention device.
-provided with a cylinder connection device compatible
with the connection for outdoor cooking gas appliances.
Always check connections for leaks each time you connect
and disconnect the LP gas supply cylinder. See
“Installation Instructions” section.
When the outdoor cooking gas appliance is not in use, the
gas must be turned off at the supply cylinder.
Storage of an outdoor cooking gas appliance indoors is
permissible only if the cylinder is disconnected and
removed from the outdoor cooking gas appliance.
Cylinders must be stored outdoors and out of the reach of
children and must not be stored in a building, garage, or
any other enclosed area.
The pressure regulator and hose assembly supplied with
the outdoor cooking gas appliance must be used. A
replacement pressure regulator and hose assembly
specific to your model is available from your outdoor
cooking gas appliance dealer.
Gas cylinder must include a collar to protect the cylinder
valve.
For appliances designed to use a CGA791 connection:
Place a dust cap on cylinder valve outlet whenever the
cylinder is not in use. Only install the type of dust cap on
the cylinder va`lve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result in leakage
of propane.
If the following information is not followed exactly, a fire causing
death or serious injury may occur.
Do not store a spare LP gas cylinder under or near this
outdoor cooking gas appliance.
Never fill the cylinder beyond 80 percent full.
SAVE THESE INSTRUCTIONS
4

INSTALLATION REQUIREMENTS
Location Requirements
Select a location that provides minimum exposure to wind and
traffic paths. The location should be away from strong draft
areas.
Do not obstruct flow of combustion and ventilation air.
Clearance to combustible construction for grill:
A minimum of 91.44 cm / 36 in must be maintained
between the front of the grill hood, sides, and back of the
grill and any combustible construction.
A 91.44 cm / 36 in minimum clearance must also be
maintained below the cooking surface, and the grill shall
not be used under overhead combustible construction.
5

INSTALLATION REQUIREMENTS
Production Dimensions
6
A. Model/serial number plate
The model/serial number rating plate is located on the inside of
the left cabinet door. See the following illustration.
A

Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local
codes and ordinances. In the absence of local codes,
installation must conform with either the National Fuel Gas
Code, ANSI Z223.1/NFPA54, Natural Gas and Propane
Installation Code, CSA B149.1, Propane Storage And Handling
Code, B149.2, or the Standard for Recreational Vehicles, ANSI
A119.2/NFPA 1192 and CSA Z240 RV Series Recreational
Vehicle Code as applicable.
IMPORTANT: Grill must be connected to a regulated gas
supply. Refer to the model/serial rating plate for information on
the type of gas that can be used. If this information does not
agree with the type of gas available, check with your local gas
supplier.
Gas Conversion:
No attempt shall be made to convert the grill from the gas
specified on the model/serial rating plate for use with a different
gas type without consulting the serving gas supplier. The
conversion kit supplied with the grill must be used. See “Gas
Conversions” section for instructions.
Gas Pressure Regulator
The gas pressure regulator supplied with this grill must be used.
The inlet (supply) pressure to the regulator should be as follows
for proper operation:
LP Gas:
Operating pressure: 11" WCP
Inlet (supply) pressure: 11" to 14" WCP
Natural Gas:
Operating pressure: 4" WCP
Inlet (supply) pressure: 7" to 14" WCP maximum.
Contact local gas supplier if you are not sure about the inlet
(supply) pressure.
Gas Supply Requirements Gas Supply Line Pressure Testing
Testing above 3.5 kPa / 1/2 psi. or 14" WCP (gauge):
The grill and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing
of that system at test pressures greater than 3.5 kPa / 1/2 psi.
Testing below 3.5 kPa / 1/2 psi. or 14" WCP (gauge) or
lower:
The grill must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal
to or less than 3.5 kPa / 1/2 psi.
Gas Connection Requirements
9.07 kg (20lb) Propane Tank
This grill is equipped for use with a 9.07 kg (20lb) Propane tank
(fuel tank not supplied). A gas pressure regulator/hose
assembly is supplied.
Any brand of 9.07 kg (20lb) Propane tank is acceptable for use
with the grill, provided that it is compatible with the grill’s
retention means (tank tray included).
It is also design-certified by CSA International for local LP gas
supply or for Natural gas with appropriate conversion.
A. Gas pressure regulator/hose assembly
A
A. Tank tray locking bracket
A
The 9.07 kg (20lb) Propane tank must be mounted and
secured.
Door Style Tank Tray
1. Open cabinet door.
2. Slide the tank tray locking bracket counterclockwise 90º
and pull out the tray
7

Natural Gas Conversion
Conversion must be made by a qualified gas technician. The
qualified Natural gas technician shall provide the Natural gas
supply to the selected grill location in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54 -latest edition,
and local codes. For conversion to Natural gas, the Natural Gas
Conversion Kit supplied with the grill (on some models) or the
Natural Gas Conversion Kit Part Number 710-0003 must be
used. See “Assistance” section for information on ordering.
IMPORTANT: The gas installation must conform with local
codes, or in the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 -latest edition.
Follow instructions for converting to Natural gas in the “Gas
Conversions” section of this manual or the instructions supplied
with Natural Gas Conversion Kit Part Number 710-0003.
The gas supply line shall be equipped with an approved shutoff
valve. This valve should be located at the same area as the grill
and should be in a location that allows ease of opening and
closing. Do not block access to the shutoff valve. The valve is
for turning on or shutting off gas to the grill.
A. Gas supply line
B. Shutoff valve “open” position
C. To grill
A
B
C
A. Locking screw
B. Bottom collar
C. Mounting hole
5. Slide the drawer with the 9.07 kg (20lb) LP gas fuel tank
back into the cabinet. Turn the tank tray locking bracket
clockwise 90ºto tighten.
A
A. Tank tray locking bracket
3. Place the 9.07 kg (20lb) LP gas fuel tank bottom collar into
the mounting hole in the tank tray.
4. Tighten the locking screw against the bottom collar of the
9.07 kg (20lb) LP gas fuel tank to secure.
8

5 6
78
910
1
3 4
2
9
x3
x3
PACKAGE PARTS LIST
x2
x5

11
13
12
10
PACKAGE PARTS LIST
TOOLS NEEDED
HARDWARE PACKAGE LIST
Truss head screw
5/32 -32X 1 1/2”
Truss head screw
1/4 -20 x 1/2" Truss head screw
5/32 -32x1 7/64”
14

1.
2.
11
ASSEMBLY INSTRUCTIONS

3.
4.
12

5.
6.
13

7.
8.
14

9.
10.
15

11.
12.
16

13.
14.
17
!

15.
16.
18
Propane tank is not included

17.
18.
19

4. Remove any debris and inspect the valve connections,
port, and gas pressure regulator/hose assembly for
damage.
NOTE: Always keep the tank at 90°(upright) orientation
to provide vapor withdrawal.
5. Using your hand, turn the gas pressure regulator/hose
assembly anticlockwise to connect to the 20 lb propane
tank as shown.
Hand tighten only. Use of a wrench could damage the
quick coupling nut.
6. Open the tank valve fully by turning the valve
counterclockwise. Wait a few minutes for gas to move
through the gas line.
7. Before lighting the grill, test all connections by brushing on
an approved noncorrosive leak-detection solution. Bubbles
will show a leak.
8. If a leak is found, turn the tank valve off and do not use the
grill. Contact a qualified gas technician to make repairs.
9. The igniter battery is not factory installed. A “AA” size
alkaline battery is in the accessory box on the grill grate.
Install battery following the instructions in “Replacing the
Igniter Battery” section.
10. Go to “Check and Adjust the Burners” section.
To Disconnect the 20 lb Propane Tank:
1. Check that the burner control knobs are in the “OFF”
position and the grill is cool.
2. Check that the 20 lb propane tank is in the “OFF” position.
If not, turn the valve clockwise until it stops.
3. Using your hand, turn the gas pressure regulator/hose
assembly clockwise to disconnect to the 20 lb propane
tank as shown.
Hand loosen only. Use of a wrench could damage the
quick coupling nut.
4. Place dust cap on cylinder valve outlet whenever the
cylinder is not in use. Only install the type of dust cap on
the valve outlet that is provided with the cylinder valve.
Other types of caps or plugs may result in leakage of
propane.
NOTE: If grill is to be converted to Natural gas, follow
instructions in the “Gas Conversions” section.
20 lb Propane Tank
IMPORTANT: : A 20 lb propane tank must be purchased
separately.
IMPORTANT: The gas pressure regulator/hose assembly
supplied with the grill must be used. Replacement gas pressure
regulator/hose assembly specific to your model is available
from your outdoor grill dealer.
To Install the 20 lb Propane Tank:
1. Install the 20 lb propane tank into the compartment below
the grill.
2. Tighten the locking screw against the bottom collar of the
20 lb propane tank to secure.
To Connect the 20 lb Propane Tank:
1. Check that the 20 lb propane tank is in the “Off” position. If
not, turn the valve clockwise until it stops.
2. Check that the 20 lb propane tank valve has the proper
type-1 external male thread connections per ANSI Z21.81.
3. Check that the burner control knobs are in the “Off”
position.
A. Gas pressure regulator/hose assembly
B. 20 lb propane tank
Gas Connection
20