SportsPlay Equipment Super Dome User manual

501-121 Super Dome
Page 1
Rev 08/07/2008
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
IMPORTANT
Please retain this information sheet in your files. It contains
important replacement parts information. All equipment should be
installed in accordance with these instructions. It is important to use
and maintain all public playground equipment properly. Playground
equipment, which is improperly maintained, can cause serious injury.
Periodical inspections, maintenance, repair and/or replacement of
damaged parts is necessary for safe operation of all playground
equipment and safety of users. Resilient surfacing should be used
under all playground equipment. Appropriate publications available at
NO CHARGE from the Consumer Product Safety Commission include a
“Handbook for Public Playground Safety”. You can receive your free
copy by calling 1-301-504-0850.
PACKING LIST
HARDWARE BAG
1
CTN
-
1
Hardware
Bag
77
-
116-545
5/16” x 2 ½” BTN HD Bolts
1
CTN
-
20
503-647
Dome Anchors
200
-
316-501
5/16” Flat Washers
2
CTN
-
15
503-220
Green Braces (2’-4” Long)
100
-
216-501
5/16” Hex Nuts
4
CTN
-
20
503-221
Black Braces (2’-8-1/2”)
100
-
326-501
5/16” Lock Washers
1
CTN
-
20
503-222
Orange Braces (2’-9” Long)
1
-
416-350
3/16” Socket Key
2
CTN
-
20
503-223
Brown Braces (2’-10-1/2”)
77
-
905-847
Bolt Cap
1
CTN
-
20
503-224
Yellow Braces (2’-11-3/4”)
1
-
803-532
Warning Label
1
-
803-524
SportsPlay Label
1
-
Maintenance Checklist
12 CTN 12 TOTAL PIECES 400# TOTAL WEIGHT CLASS 70
Use Area is a 29’
Diameter Circle
Ground Space is a 17’
Diameter Circle

501-121 Super Dome
Page 2
Rev 08/07/2008
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
GENERAL ASSEMBLY INSTRUCTIONS:
1. Check each piece CAREFULLY and REMOVE any sharp projections that may have been caused
by shipping.
2. DO NOT TIGHTEN nuts more than hand tight until entire assembly is completed.
3. ALL threaded ends of bolts protruding beyond nuts should be cut off and peened over to remove
any sharp edge.
SPECIFIC ASSEMBLY INSTRUCTIONS:
NOTE: Extra long bolts are supplied to make assembly possible
1. Bolt bottom row together using 5/16” x 2 ½” Button Head Bolts with one washer under bolt head
and one bolt cap with one washer, one lock washer under one hex nut. Follow color scheme on
page 4 sketch.
2. When circle is complete, mark footing holes at each joint, move circle aside and dig holes.
3. Move back over holes and bolt dome anchors in place using a washer on both sides of the dome
anchor and a lock washer under the hex nut.
4. Continue adding rows, working around climber using hardware as in step #1. Always position
bars where ends point up on bottom so that ends of bars pointing down are on top. BE SURE to
assemble all joints loosely until entire climber is completed.
5. When climber is completely assembled, tighten all bolts securely by first tightening down joined
braces with C-Clamp or similar. Cut off bolt ends so that no more than two threads extend beyond
face of nut. Peen or file to remove sharp edges. Allow for proper depth of resilient surfacing.
Place bolt covers over bolt caps
6. Pour footings up to 3” from top and allow at least 48 hours to harden.
7. Cover tops of footings with dirt.
8. Attach warning label and Manufacturer’s Identification Label to a clean surface. The labels
should be attached in a location where they are clearly visible and legible and away from normal
hand and foot placement areas. The labels must be replaced if they become illegible, destroyed or
removed. Contact your distributor for replacement labels.

501-121 Super Dome
Page 3
Rev 08/07/2008
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
Footing Diagram

501-121 Super Dome
Page 4
Rev 08/07/2008
SportsPlay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
www.sportsplayinc.com
Installation Key