SPORTSPOWER 4XMNK User manual

1820mm
2390mm
2200mm
APPROXIMATE ASSEMBLY TIME 2 PERSON ASSEMBLY REQUIRED ASSEMBLY SPACE
45
FLOOR AREA
3M x 2M x 2M
REQUIRED ASSEMBLY TOOLS
minutes
ASSEMBLED DIMENSIONS
WEIGHS16.1KG, BUILD IN LOCATION
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

1.Please check that all parts are present before
you start the assembly of your swing, as once
assembled, the swing is exempt from our home
approval policy.
2.For ease and speed of assembly, we
recommend that before you commence each
step of assembly, you should identify all the
parts required for that step.
TOP TIPS BEFORE YOU START
3.For larger items, please ensure that you have
sufficient space and people(as indicated on
page 1) to assemble your product safely.
4.During assembly, please take care not to
over-tighten any fittings, as this may damage
the product.
5.Please retain these instructions for future
reference.
UK WARNINGS
Read and follow all instructions.
WARNING! Not suitable for children under
36 months. Small parts/long cord-
Strangulation Hazard.
This unit is designed to be used safely by
up to 3 children between the age of 3 to 8.
Maximum weight of 50kg each,
simultaneously not to exceed a combined
weight of 150kg.
No more than one user allowed on each seat.
The equipment is designed for outdoor
domestic use only and is not suitable for hiring
or commercial use.
Adult assembly required. Adult supervision is
required at all times while the swing is in use.
Never leave children unattended during play, or
use the equipment in any manner other than as
intended.
Never allow children to disembark from the
play equipment whilst it is still in motion.
Ensure that children are not facing the sun
whilst using the equipment.
Do not attach items to the equipment that are
not specially designed for use with this product,
including but not limited to cables, skipping
ropes and chains as they may cause
strangulation hazards.
Never allow children to walk too close to, in
front of, behind or in between the equipment
whilst in use. Always keep children a safe
distance from the product whilst in use.
Do not allow reckless playing, such as jumping
off, standing on seats or climbing ropes.
Do not allow children to use wet seats or during
rainy or windy conditions.
Instruct children to avoid swinging the empty
swing, twisting swing chains or ropes or
looping them over the top support bar since
this may reduce the strength of the chain or
rope.
Do not allow children to climb on the swing
frame (legs, top bar, cross bars and other
parts) these are structural components only
and not play features.
Instruct children to sit in the centre of the
swing, with their full weight in the middle of the
seats.
Ensure that children wear suitable clothing
whilst using this equipment. Never allow
children to wear loose clothing, neck ties,
scarves, clothing with drawstrings or loose
jewellery.
Please remove all packaging and packing
tags/wires before allowing children to use.
Please take note: As an extra precaution,
check this toy regularly for signs of wear or
damage.
TIPS: BEFORE STARTING ASSEMBLY,
PLEASE CHECK ALL PARTS ARE INCLUDED,
IF ANY PARTS ARE MISSING, PLEASE CALL
([phone]
PAGE 2 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

At the start of assembling, do not tighten
bolt/nuts all the way, so as to allow some
possible adjustment, for ease of assembly.
TIGHTENING NUTS & BOLTS
After all major components are assembled, go
back over all bolts and nuts and properly
tighten all of them before using this product.
ANCHOR WARNING
The product should not be installed over
concrete, asphalt or any other hard surfaces.
The equipment should be placed on a level
surface at least 2 m from any structure or
obstruction such as a fence, garage, house,
overhanging branches, laundry lines or
electrical wires.
Do not use the equipment until it has been fully
assembled and anchored, and all the
components are secured. All the chains/ropes/
cables cannot be looped back on themselves.
The anchor must be placed level with or under
the ground in order to reduce tipping hazards.
Protective surfacing: One of the most important
things you can do to reduce the likelihood of
serious head injuries is to install
Shock-Absorbing Protective Surfacing (over
the ground) under and around your play
equipment. If you use loose -fill materials as a
surface, please follow these guidelines:
Maintain a minimum depth of 9 inches of
loose-fill materials such as wood mulch/chips,
engineered wood fibre, or shredded/ recycled
rubber mulch for equipment up to 8 feet high,
and 9 inches of sand or pea gravel for
equipment up to 5 feet high. NOTE: an initial fill
level of 12 inches will compress to about 9 inch
depth of surfacing over time. The surfacing will
also compact, displace and settle, and should
be periodically refilled to maintain at least a 9 -
inch depth. Carpeting and thin mats are
generally not adequate protective surfacing,
check and maintain the depth of the loose-fill
surfacing material to maintain the right amount
of loose-fill materials. Do not install loose fill
surfacing over hard surfaces such as concrete
or asphalt.
CARE AND MAINTENANCE INSTRUCTION
Please carry out checks and maintenance of
the main parts (crossbeams, suspensions,
anchors nuts and bolts) at regular intervals.
If these checks are not carried out the toy could
overturn or otherwise become a hazard.
It is of particular importance that they be
followed at the beginning of each season as
well as at regular intervals during the usage
season.
Check all nuts and bolts for tightness and
tighten when required.
Oil all metallic moving parts;
Check all coverings for bolts and sharp edges
and replace when required;
Check swing seats, chains, ropes and other
means of attachments for evidence of
deterioration. Replace when required in
accordance with the manufacturer's
instructions.
Remove plastic parts, such as swing seats or
similar parts or do not use when temperature
drops below 32 degree F(0 degree C).
PAGE 3 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Tighten all hardware.
Lubricate all metallic moving parts per
manufacturer's instructions.
Check all protective coverings on bolts, pipes,
edges, and corners, replace if they are loose,
cracked, or missing.
Check all moving parts including swing seats,
ropes, cables, and chains for wear, rust or
other deterioration. Replace as needed.
Reinstall any plasic parts, such as swing seats
or any other items that were removed for the
cold season.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as
necessary.
At the beginning of each play season:
Tighten all hardware.
Rake and check depth of loose fill protective
surfacing materials to prevent compaction and
to maintain appropriate depth. Replace as
neccessary.
Twice a month during play season:
At the end of each play season or when the
temperature drops below 32 degress F(0
DEGREES C).
Remove plastic swing seats and other items as
specified by the manufactured and take indoors
or do not use.
At the end of each play season:
Please disassemble with care when it is no
longer in operational condition.
Wear heavy duty working gloves!
Consumer may wish to recycle the steel tubing,
please take the frame to your local recycling
center.
Do not leave partially disassembled equipment
accessible by children.
All plastic parts could be recycled, take it to you
local recycling centre.
All rusted parts and bolts shall be properly
disposed of in houseware waste. Do not reuse.
Do not let children play with any disassembled
parts destined for disposal, such as chain,
tubings, bolts, nuts, screws!
Disposal Instructions
WARNING
PAGE 4 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

1
2
3
3
4
4
5
6
7
7
8
9
9
8
5
4
4
11
12
16
16
18
18
18
18
15
17
12
14
13
10
10
10
10
3
3
PAGE 5 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

QTYPART LISTNO.
1
2
6
7
8
TOP SUPPORT BAR
1
1
1
2
2
9
44
416
217
111
213
212
215
214
410
25
418
GLIDER SUPPORT CHANNEL
GLIDER TOP TUBE
GLIDER LOWER TUBE
GLIDER SEAT TUBE
LOWER LEG
PLASTIC CONNECTOR
FOOTREST
SWING SEAT
PLASTIC CONNECTOR
GLIDER SEAT
PLASTIC SLEEVE
PLASTIC TUBE
ANCHOR
CROSS BAR
PLASTIC CAP
2
TOP SUPPORT BAR
4UPPER LEG3
PAGE 6 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
SW013H-TOPSPPRTBAR
SW013H-
TOPSPPRTBAR2
SW013H-PLSTCSLV
SW-ANCHOR2
SW-XBAR
SW-FTREST
SW-GLDSEAT
SW031H-SUPCHANNEL
SW-GL01
SW013H-GLDSTTB
SW013H-TPTB
SW-LOWLEG
SW-TPLEG
SW-SEAT1
SW-PLASCONN
SW-PLASCONN2
SW-PLSTCTB
SW-CAP
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT

0cm
10cm
9cm
8cm
7cm
6cm
5cm
4cm
3cm
2cm
1cm
11cm
12cm
"U" BOLT
M8×114mm
X2
A
BOLT
M8×61mm
X6
B
BOLT
M8×66mm
X4
C
BOLT
M8×50mm
X2
E
BOLT
M6×34mm
X2
F
BOLT
M6×60mm
X2
G
BOLT
M6×36mm
X4
I
BOLT
M8×95mm
X2
H
BOLT
M8×20mm
X2
D
PAGE 7 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
GEN-BOLTM6X36
GEN-BOLTM6X60
GEN-BOLTM8X20
GEN-BOLTM8X50
GEN-BOLTM8X61
GEN-BOLTM8X66
GEN-BOLTM8X95
GEN-UBOLTM8X114
GEN-BOLTM6X34
VIEW PRODUCT VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT
VIEW PRODUCT

0cm
10cm
9cm
8cm
7cm
6cm
5cm
4cm
3cm
2cm
1cm
ARC
WASHER
Ø19×8.5mm
X28
J
FLAT
WASHER
Ø19×8.5mm
X12
K
ARC
WASHER
Ø14×6.5mm
X12
L
SPRING
WASHER
Ø8×2mm
X20
M
SPRING
WASHER
Ø6×1.5mm
X8
N
CAP
NUT
M8
X20
O
CAP
NUT
M6
X8
P
PAGE 8 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
GEN-SPRWASH-6X1.5
GEN-SPRWASH-8X2
GEN-FLATWASH-19X8.5
GEN-ARCWASH-14X6.5
GEN-ARCWASH-19X8.5
GEN-CAPNUT-M6
GEN-CAPNUT-M8
VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT VIEW PRODUCT

SPANNER
10&13mm
X1
Q
ALLEN KEY
4mm
X1
R
ALLEN KEY
6mm
X1
S
0cm
10cm
9cm
8cm
7cm
6cm
5cm
4cm
3cm
2cm
1cm
PAGE 9 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]
GEN-SPAN5-11-13 GEN-ALWR4MM GEN-ALWR6MM
VIEW PRODUCT VIEW PRODUCT
VIEW PRODUCT

Step 1
D
x 2pcs
K
x 4pcs
M
x 2pcs
O
x 2pcs
D
D
O
O
M
M
K
K
K
K
1
6
PAGE 10 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 2
1
2
B
J
M
O
2
1
B
x 2pcs
J
x 4pcs
M
x 2pcs
O
x 2pcs
PAGE 11 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 3
1
3
3
2
3
3
B J MO
3
B
x 4pcs
J
x 8pcs
M
x 4pcs
O
x 4pcs
PAGE 12 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 4
A
x 2pcs
J
x 8pcs
M
x 4pcs
O
x 4pcs
11
2
J
M
O
J
A
1
PAGE 13 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 5
E
x 2pcs
K
x 4pcs
M
x 2pcs
O
x 2pcs
E
EK
KKMO
KMO
77
6
14
14
13
7
6
13
7
PAGE 14 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 6
4
4
33
4
3
4
5
5
CJM
K
O
4
3
5
18
K
x 4pcs
J
x 4pcs
M
x 4pcs
O
x 4pcs
C
x 4pcs
PAGE 15 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 7
7
7
88
7
8
F
L
L
N
P
F
x 2pcs
L
x 4pcs
N
x 2pcs
P
x 2pcs
PAGE 16 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 8
J
JMO
H
16
9
9
8
15
H
x 2pcs
J
x 4pcs
M
x 2pcs
O
x 2pcs
9
8
8
PAGE 17 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 9
12
12
9
L
I
N
P
12
9
I
x 4pcs
L
x 4pcs
N
x 4pcs
P
x 4pcs
PAGE 18 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

8
PNL
G
L
17
17
17
8
8
Step 10
G
x 2pcs
L
x 4pcs
N
x 2pcs
P
x 2pcs
PAGE 19 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]

Step 11
30
cm Width
30 cm Depth
Concrete
Ground
minimum clearance between the
footrest and the ground.
IMPORTANT: The product must be anchored into the ground.
For optimum safety and performance, we recommend concreting
in the corners as shown in the diagram.
10
4
PAGE 20 OF 21
4XMNK
DESCRIPTION:
TITAN DELUXE SWING & GLIDER
ASSEMBLY
INSTRUCTION
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong.
After Service Centre ([phone]