SPORTSPOWER Climb with slide WP-730 Maintenance manual

ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USE INSTRUCTONS
Sportspower Ltd.
20/F, Parkview Centre, 7 Lau Li Street, Causeway Bay, Hong Kong
www.sportspowerltd.net
MODEL NO.: WP-730
Assembly Size: 244 x 140 x 104cm
Climb with slide
WARNING
!
DO NOT RETURN PRODUCT TO THE STORE. FOR CUSTOMER SERVICE OR REPLACEMENT
PARTS, PLEASE CALL ([phone], email [email protected] or visit
www.sportspowerfit4kids.com
Carefully read the entire manual before assembling and using this product.
This product is intended for use by children ages 3yrs+.
Assembly requires at least TWO adults.
Maximum user weight is 45kg, maximum combined user weight 135kg.
Maximum of 3 children to use this item at one time.
Always inspect product thoroughly before each use.
Warning! Only for outdoor use.
Warning! Only for domestic use.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

2
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT
AGE LIMIT

This product is intended for use by children ages 3yrs+.
On-site adult supervision is requiredat all times for children of all ages.
Do not allow use by children with any physical condition that may affect his/her ability to use this




equipment safely.


Hardware:
To check all nuts and bolts for tightness and replace when required. Hardware should be firmly
against, but not crushing the wood. Over-tightening hardware crushes wood fibers and can split
wooden components resulting in the bolt thread extending beyond the wood. This poses a
severe safety hazard. If bolt threads protrude beyond the wood surface, replace the bolt with a
shorter one that will not protrude. If splintering has occurred from over-tightening, larger washers
can be purchased at your local hardware store and installed under the bolt head. Be sure to
reuse or replace your lock washers.
Major Wooden Parts:
Inspect for structural defects and splintering. If necessary, lightly sand and refinish with an
exterior water repellent stain. Seasonal checking or cracking of the grain on wooden parts is
quite natural water and heat are the most frequent causes of expansion and contraction of wood
fibers. Our wood set has been treated with stain to resist weathering. But it needs to be
maintained periodically by applying new stain or paint. To replace defective parts in accordance
with the manufacture’s instructions.
IMPORTANT:
Children must NOT play on this set until it is properly assembled and inspected by an adult.
The product must be properly installed BEFORE by children use.
You MUST read and follow all instructions in this manual before installing or attempting to use this
product.
Failure to follow these important requirements may result in the warranty being voided and/or serious
injury. Please supervise your children carefully during the installation and assembly of the product.
Please also pay close attention to the periodic maintenance that is required to keep your set in a safe
condition for maximum enjoyment of backyard fun!
Im
p
ortant
–
Please read these instructions thorou
g
hl
y
before assembl
y
or use.
IMPORTANTWARNINGS AND INSTRUCTIONS
IMPORTANT WARNINGS AND INSTRUCTIONS
BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and using
this product.The unit must be assembled by adults. Heavy duty working gloves should be worn to avoid
injuries during assembly.
Children must NOT play on this set until it is properly assembled and inspected by an adult.
Do not allow children to jump off the product.
Do not allow more than four children to play at the same time.
DO NOT allow children under three years old nearby during assembly. Small parts may cause
choking hazard.

3
BEFORE YOU BEGIN ASSEMBLY:
Take a complete inventory of components using the parts list.
Sort and lay out the wood. Label each piece of wood for easy reference. For easy
identification during the assembly process, write the board’s letter on masking tape and adhere to
each piece of the wood. Some wooden components may twist or warp in the carton after packaging.
Usually, these parts straighten out when assembled. You may also see some cracking of the grain.
This is normal.
Sort all hardware according to size. Do not worry if extra hardware is included.
FIND A SAFE PLAY LOCATION.
You MUST install the product on level ground. Uneven ground must be leveled prior to installation.
The manufacturer cannot assume responsibility for any failure from incorrect installation.
Installingonsloping ground will put stress on all the joints, which will cause the set tobecome loose
and unstable.
Find a location where the equipment can be placed more than 2 meters from any structure or
obstruction (ex: electrical wires, branches, house, fence, garage). The safe play area refers to a zone
extending 2 meters beyond the gym set on all sides, includingthe space above the play set.
The safe play area must be free of all structures, landscaping, tress and branches, rocks, wires and
other obstacles tosafe play. Children can be seriously injured running into these obstacles.
Remove any rocks or any jagged or sharp object that could endanger your children’s’ safety.
Remove all tripping hazards from the safe play area. Tripping hazards include but are not limited to:
roots, stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing, and electrical
connections.
Do NOT install your play set over gravel, asphalt, packed earth or any other hard surface.
Im
p
ortant
–
Please read these instructions thorou
g
hl
y
before assembl
y
or use.
IMPORTANTWARNINGS AND INSTRUCTIONS
IMPORTANT WARNINGS AND INSTRUCTIONS

4
Tools Required for Assembly (Not Included)
Phillips Head Screwdriver
Phillips Head Screwdriver
Electric Drill
Working Gloves
Ladder or Step Tool

5
NO.
1 1
1
2
2
4
2
2 1
1
3
3
4
6
7
3
1
1
8
1
9
10
11
12
13
14
15
16
17
18
19
20
2
1
1
1
8
1
1
5
PICTURE QTY
Wood parts list

6
Wood parts list
NO.
21 1
1
2
8
1
8
22 1
1
23
1
24
26
27
28A
28B
29
U1
U4
U11
1
1
6
2
25
PICTURE QTY

7
Hardware parts list
NO. DESCRIPTION PICTURE QTY
M8×28mm
M8×45mm
M6×28mm
M4×28mm
M4×35mm
M4×45mm
M4×40mm
M6×27mm
M6×40mm
M6×50mm
M8
M4
M6
M8
M6
Allen Wrench (M6)
Allen Wrench (M5)
Allen Wrench (M4)
B1
B2L
B30
L5
L6
L7
L11
S1
S2
S3
V9
V31
V2
V8
V20
V21
V22
V23
4
4
12
8
81
36
4
2
5
13
8
12
12
8
20
1
1
1

Step 1
Assembly Instructions
FIGURE 1
8
 First, connect #5 to #1 and #3 using L6 (4pcs), then connect #6 to #1 and #3 using L6 (4pcs).
 First, connect #5 to #2 and #4 using L6 (4pcs), then connect #6 and #23 to #2 and #4 using L6 (8pcs).
Wood Boards Needed:
Part No. Quantity
5 2
2
6
1
23
1 3
2 4
L6
L6
L6
L6
L6
Hardware Needed:
Part No. Quantity
L6 20
6
6
23
5
5

 Place #7 onto the frame using L7 (4pcs) as shown.
 Connect #20 to #1 and #2 using S3 (4pcs) and V20 (4pcs).
Wood Boards Needed: Hardware Needed:
Part No. Quantity Part No. Quantity
7 1
1
L7 4
20 S3 4
V20 4
L7
L7
7
20
1
3
2
4
S3,V20
S3,V20
Step 2
Assembly Instructions
FIGURE 2
9

Wood Boards Needed: Hardware Needed:
Part No. Quantity Part No. Quantity
25 1
25
2
4
B2L,V8
V9
B2L,V8
V9
B2L 4
V8 4
V9 4
 Connect #25 to #2 and #4 using B2L (4pcs), V8 (4pcs) and V9 (4pcs).
Step 3
Assembly Instructions
FIGURE 3
10
4
25