SPRT SP-Y32 User manual

SPRT®
Android POS Terminal
User’s Manual
（SP-Y32）
（Ver 1.02）
Beijing Spirit Technology Development Co.,Ltd

Content
Brief introduction............................................................................................................................................1
Chapter 1 Features and performance.....................................................................................................1
1.1 Printing Performance............................................................................................................................. 1
1.2 Paper Roll................................................................................................................................................ 1
1.3 Print characters.......................................................................................................................................2
1.4 Interface Mode........................................................................................................................................ 2
1.5 Print Control Commands.......................................................................................................................3
1.6 Power Requirements............................................................................................................................. 3
1.7 Working Environment.............................................................................................................................3
1.8 Dimensions.............................................................................................................................................. 3
1.9 Model Name............................................................................................................................................ 4
Chapter 2 Operating Instructions.............................................................................................................4
2.1 Printer appearance.................................................................................................................................4
2.2 Install the paper roll................................................................................................................................5
2.2.1 Install paper roll........................................................................................................................... 5
2.2.2 Cutter jamming............................................................................................................................ 6
2.3 Interface connection...............................................................................................................................6
2.3.1 USB-TypeA.................................................................................................................................. 6
2.3.2 Ethernet Interface........................................................................................................................6
2.3.3 USB Interface...............................................................................................................................6
2.3.4 Bluetooth.......................................................................................................................................7
2.3.5 WIFI............................................................................................................................................... 7
2.3.6 4G USB DONGLE.......................................................................................................................7
2.3.7 Cash Drawer Port........................................................................................................................8
2.3.8 Power connection........................................................................................................................8
2.4 Indicators, Buzzers, and Key Operation.............................................................................................9
2.5 Normally powered on...........................................................................................................................10
2.6 Self-testing.............................................................................................................................................10
2.7 Hexadecimal printing........................................................................................................................... 11
2.8 Printer Parameter Settings................................................................................................................. 12
2.9 Entering Program Upgrade Mode..................................................................................................... 12
Appendix A: Parameter Settings.............................................................................................................. 13

1
Brief introduction
Y32 smart machine is a type of printer suitable for lottery industry. The main screen is
7-inch LCD screen vertical screen, the auxiliary screen is HDMI 4K HD display interface. The
Android system supports mobile, China Unicom, telecommunications three 4G communications
network. Y32 has 100M wired network port, Wi-Fi/BT4.0, and USB standard interface. The 500W
camera module support scanning one-dimensional code, two-dimensional code. Y32 also
support paper near function and accurate measurement, black mark 6 position adjustable
(positive and negative 3 positions), paper width compatible 80mm and 82.5mm, and the effective
width is 72mm, paper roll diameter is 120mm.
Chapter 1 Features and performance
1.1 Printing Performance
Printing method: direct thermal printing
● Paper width: 80mm/82.5mm
● Print density: 8 points/mm, 576 points/line
● Print speed: 150mm/s (maximum)
● Reliability:
(1) Print head life: 100km
Conditions of Use:
* Print 12×24 Spanish characters, print 50 lines each time, repeat printing intermittently.
* Use specified thermal paper
(2) Cutter life: 1,000,000 times. Conditions of Use: Less than 30 times per minute
● Effective print width: 72mm
Statement
This is a Class A product. In a living environment, this product may cause radio
interference. In this kind of circumstances, the user may need to take practical measures
against the interference.

2
1.2 Paper Roll
Thermal Paper Roll: Paper Width ---------- 82.5±0.5mm (Maximum)
Outer diameter ---------- Φ120mm (maximum) Φ
Inner diameter ---------- Φ13mm (minimum)
Thickness ---------- 0.06mm～0.08mm
1.3 print characters
● Western character set:
12 × 24 dots, 1.5 (width) × 3.00 (high) mm
● Chinese characters:
24 x 24 dots, 3.00 (width) x 3.00 (height) mm
1.4 Interface Mode
● USB-TypeB interface:
The standard USB print interface
● HDMI-TypeA interface:
One HDMI 2.0 supports 4K 60Hz display and supports HDCP 1.4/2.2.
● Ethernet interface:
Isolate the standard Ethernet interface.
● USB-TypeA interface:
There are 4 standard USB host interfaces.
● Bluetooth interface:
Realtek Realtek RTL8723BS series Bluetooth Bluetooth module SDIO interface. Bluetooth4.0
(supports iBeacon+eddystone protocol)
● WIFI interface:
Realtek Realtek RTL8723BS series Bluetooth Bluetooth module SDIO interface.
IEEE802.11b/g/n.
● 4G network
One of the 4G Internet access modules which supported the PCIE interface such as CE20C,
U9300W, and USB DOGNLE CLM920, can be connected to the Internet. Can switch
between WiFi, Ethernet, GPRS and 4G smoothly; select data link according to the priorities
of Ethernet, WiFi, 4G and GPRS.

3
● Camera interface:
The 500W camera module interface recognizes one-dimensional and two-dimensional
barcodes as follows:
1. One-dimensional code 1D product: UPC-A, UPC-E, EAN-8, EAN-13.
2. One-dimensional code 1D industrial: Code 39, Code 93, Code 128, Codabar, ITF,
RSS-14, RSS-Expanded.
3. Two-dimensional code 2D: QR Code, Chinese QR Code, Micro QR Code, Big Data QR,
Data Matrix, Aztec (beta), PDF417 (beta).
4. Can quickly respond to one-dimensional code and two-dimensional code
scanning in 0.5-1 seconds, scan distance is within 15cm.
● Cash box control:
Power supply DC24V1A, interface type 6-wire RJ-11 socket.
● Speaker
Built-in cavity speaker larger than 2W (output volume at four points around the printer
around the front and back and left and right, the maximum volume is not less than 90
dB)
●Display screen:
MIPI interface, resolution 720*1280 (vertical screen)
● Touch screen:
5-point capacitance type touch screen, G+G specification fully-fitted process.
● Operating System
Android 5.1 or above and support OTA upgrade.
● Processor
RK3288 quad-core Cortex-A17, clocked at up to 1.8GHz, Mali-T764 GPU, supports
AFBC (Frame Buffer Compression), OpenGL ES 1.1/2.0/3.1, OpenCL, DirectX9.3,
embedded high-performance 2D acceleration hardware.
● Memory
DDR3, 2GB
●Storage
8GB eMMC
● TF card interface
Supports up to 32GB
● Internal clock
Supports automatically determining the date and time of the network. The RTC time can
be maintained for at least 1 month without loss after power off.

4
1.5 Print Control Commands
● character print command:
Supports double-width and double-height printing of ANK characters, custom characters,
and Chinese characters, and can adjust the line spacing of characters.
● Dot print command:
Supports different density dot plots and download graphics printing.
●GS barcode printing command:
Support UPC-A, UPC-E, EAN-13, EAN-8, CODE39, ITF25, CODABAR, CODE93,
CODE128, PDF417, QR Code, DATA Matrix barcode printing.
1.6 Power Requirements
Power adapter DC24V ±10%, 2.5A, DC005-2.5 power outlet
1.7 Working Environment
● Operating temperature:
0°C～50°C Operating Relative Humidity: 10%～80%
● Storage temperature:
-20°C～60°C Storage Relative Humidity: 10%～90%
1.8 Dimensions
275（L）mm×140（W）mm×150（H）mm
1.9 Model Name
Model
Interface
SP-Y32
USB-TypeA、HDMI、USB-TypeB、Ethernet、Cash
Drawer

5
Chapter 2 Operating Instructions
2.1 Printer appearance
The names of printer parts are shown in Figure 2-1

6
Figure 2-1 Name drawing of each part of the printer
2.2 Install the paper roll
2.2.1 Install paper roll
The SP-Y32 uses 80mm/82.5mm wide thermal paper roll.
Thermal paper installation steps are as follows:
Press the right cover open button to open the paper cover, put the thermal paper roll into the
paper warehouse, pull a section from the paper roll, then put the paper end on the head, cover
the paper cover, Gently press down.
1. Pay attention to the direction of loading paper, make the printing surface
face to the print head.
2. Please don’t feed or draw the paper forwards or backwards with hands.
3. Keep clean of the print head, avoid to influence the printing quality.

7
2.2.2 Cutter jamming
If the cutter is stuck, turn off the power switch, re-power, the cutter can return to its original
position.
2.3 Interface connection
2.3.1 USB-TypeA
The Y32 supports four USB-TypeA master interfaces. Each pin is defined as shown in Figure 2-2.
PIN
Assignment
Function
Mark
1
V Bus
Power
Positive5
V
2
Data -
Data
Negative
3
Data +
Data
Positive
4
GND
Power
Ground
Figure 2-2 USB-TypeA
2.3.2 Ethernet Interface
The network port configuration uses an RJ45 network socket. The appearance is
shown in Figure 2-3:
Figure 2-3 Ethernet
2.3.3 USB Interface
The standard configuration of the Y32 smart one is equipped with a standard USB printer
cable D-type data cable for connecting the printer and the host device. The printer's USB is a

8
slave device type (DEVICE); the outline and pin definitions are shown in Figure 2-4:
PIN
Assignment
Function
Mark
1
V Bus
Power
Positive
5V
2
Data -
Data
Negative
3
Data +
Data
Positive
4
GND
Power
Ground
Figure 2-4 USB-TypeB
2.3.4 Bluetooth
A handheld device, laptop, or other information terminal with a Bluetooth interface can
communicate with the all-in-one through a Bluetooth interface. Y32 smart machine Bluetooth 4.0
is compatible with the Bluetooth 2.0 Bluetooth specification, the power level is CLASS 1.5 or
CLASS 2, and the effective distance is 10m. The initial device name of the all-in-one is rk3288.
You can modify the device name as needed.
The Y32 smart all-in-one needs to be paired with the Bluetooth device of the control
all-in-one before it works. Pairing can be initiated by either party. The usual pairing process is as
follows:
1. The Bluetooth device of the all-in-one and control integrated machine is turned on.
2. The bluetooth device of the all-in-one or control one machine searches for an external
Bluetooth device and selects the corresponding Bluetooth device.
3. Confirm and receive pairing on the Bluetooth device or the all-in-one of the control device.
2.3.5 WIFI
The common WIFI interface and WIFI connection network mode are the same as ordinary
mobile phone connection WIFI. After finding a suitable WIFI hotspot AP, the corresponding
authentication password can be entered to complete the WIFI login.

9
2.3.6 4G USB DONGLE
Y32 can be equipped with CLM920 4G USB DONGLE. After starting up, it will automatically
complete network registration and connect to 4G network. Users do not need related operations.
Note: The 4G SIM card used by the 4G USB DONGLE guarantees that you can use the local
area to access the Internet normally and have sufficient charges. Otherwise, there will be
disconnection failures.
2.3.7 Cash Drawer Port
The cash box interface of the Y32 is an RJ-11-6 cable socket, as shown in Figure 2-5.
Figure 2-5 Cash Drawer Port
PIN Assignment:
PIN Assignment
Signal
Flow Direction
1
Architecture Ground
---------
2
Cash Drawer Driver Signal 1
Output
3
Cash Drawer ON/OFF Status
Signal
Input
4
+24VDC
---------
5
Cash Drawer Driver Signal 2
Output
6
Signal Ground
---------
2.3.8 Power connection
The rated supply voltage is 24V±10% DC, the rated current is 2.5A, and the DC005-2.5
power socket is used. The polarity is positive and negative. Use the standard power adapter
supplied with the printer to power it. The outline and pin definitions are shown in Figure 2-6
below:

10
PIN Assignment:
Figure 2-6 Power Port
2.4 Indicators, Buzzers, and Key Operation
The Y32 has a button, a built-in buzzer, a red, yellow, and green three-color status indicator
and a power indicator (green).
[FEED] is the paper feed key. You can use the print command to enable or disable the key
switch function. When the key control is enabled, press the [FEED] key to feed the paper, and
release the [FEED] key to stop the paper feed.
The buzzer is used to indicate the type of error status. It can be set by parameter setting to
enable or disable the error alarm. The error status type is the same as the ERROR indicator.
The green POWER indicator is the power indicator. The POWER indicator is on to indicate
that the printer is on.
The red/yellow/green color ERROR/ALARM/RUNNING indicator is the error status/reminder
indicator/normal operation. When the printer works normally, the green indicator lights up. The
red indicator lamp flashes as the abnormal alarm status. When the red indicator lamp lights up, it
indicates that the indicator is off. The paper deck cover opens during printing. The yellow
indicator light indicates that there is no paper or the paper is near.
The error light flashes and the buzzer sounds: The printer has an error.
Different types of flashing indicate the printer's error type:
1. Unrecoverable error. The number of indicator flashes and the number of buzzer rings
indicate the type of error. It then lights up for a period of time.
2. The error can be recovered. The number of indicator flashes and the number of buzzer
rings indicate the type of error, and then it will be off for a long time.
3, automatic recovery error, continuous flashing light, buzzer continuous ring.
4, lack of paper, lack of paper lights long, buzzer sounded long. When the printer paper
compartment cover is opened, it is no longer detected whether the printer is out of paper, only the
presence of paper is detected.
The error indication is as follows:
Unrecoverable error: The error indicator flashes several times and then lights up for a period
of time, then loops. The number of flashes indicates the type of error.
PIN
Assignment
Signal
1
+24V
2
Ground

11
Error
Description
ERROR light Blinks Way
Unrecoverable
Error
LED blinks once: Memory read and write errors
LED blinks twice: Overvoltage
LED blinks three times: Undervoltage
LED blinks four times: CPU execution error
(error address)
LED blinks five times：UIB error
LED blinks six times: FLASH writes error
LED blinks seven times: Parameters write error
LED blinks eight times: temperature detection
circuit error
1recoverable error, the indicator light flashes continuously, then long off for a period of
time.
Error
Description
ERROR light Blinks Way
Recoverable
Error
LED blinks once: Cutter position error
2Errors that can be automatically recovered, the indicator light blinks continuously.
Including print head temperature error and cover open error during printing.
Error
Description
ERROR Light Blinks Way
Automatically
recoverable
errors
LED blinks continuously: The print
head is overheated and the cover is
open during printing.
2.5 Normally powered on
In the off state, the paper cover is closed, then the power switch is turned on, the power
indicator light is on, the status indicator red and yellow bi-color indicator light flashes twice, then
the green light is on, and the printer enters the normal operation mode.

12
2.6 Self-testing
The self-test can detect whether the printer is working properly. If the self-test spline can be
printed correctly, it means that the printer is normal except for the interface with the host,
otherwise it needs to be repaired.
The self-tests are printed out in order: manufacturer name, printer model, software version,
interface type, default value of printer parameters, 96 characters in ASCII code, default code
page content (language setting in English) or Kanji library name ( If the language is set in
Chinese), the barcode type.
Self-test method is to hold down the [FEED] key and turn on the power switch, then the printer
will print a self-test spline immediately. The spline form is shown in Figure 2-7:
Figure 2-7Sample for self testing
2.7 Hexadecimal printing
Follow the steps below to turn on the printer to put it into hexadecimal printing mode.
1. Open the paper cover;

13
2. Hold down the [FEED] key and turn on the power switch.
3, close the paper cover, then print out the following 3 lines:
Hexadecimal Dump
To terminate hexadecimal dump,
Press FEED button three times.
Indicates that the printer enters hexadecimal mode. In this mode, all input will be printed as a
hexadecimal number. Each press of the [FEED] key moves one line, accumulates three times,
and prints out “*** Completed * **", exit the hex print mode.
2.8 Printer Parameter Settings
This function is to set some simple parameters of the printer.
Enter the parameter setting method:
In the off state, first open the [paper bin cover], hold down the [FEED] key, then turn on the
power switch, and then release the [FEED] key after the status light and paper out light flash
alternately. Then press the [FEED] key twice and close the [paper bin cover]. The printer enters
parameter setting mode. And print out the first set of parameters and their current settings. For
detailed setting method, please refer to Appendix A.
Exit the parameter setting method: first open the [paper bin cover], then hold [FEED] key,
then close [paper bin cover] and release [FEED] key, save the set parameter value and exit the
parameter setting mode. Enter normal working mode.
If the printer power is turned off directly, the set parameter values are not saved.
2.9 Entering Program Upgrade Mode
In the off state, first open the [paper bin cover], hold down the [FEED] key, and then turn on
the power switch. After the status light and paper out light flash alternately, release the [FEED]
key. Then press the [FEED] key five times, then close the [paper bin cover]. The printer enters
program upgrade mode. The status indicator flashes at approximately 1 second.
Quick access method: In the off state, first open the [paper bin cover], hold down the [FEED]
key, turn on the power switch, and then quickly release the [FEED] key. The printer enters
program upgrade mode. The status indicator flashes at approximately 1 second.
Note: When the upgrade mode is entered, the out-of-paper indicator light indicates that the
interface cannot perform program upgrades. Currently, only the USB-TypeB interface supports
online program upgrades.

14
Appendix A: Parameter Settings
This appendix is a method to set the printer's default parameters by pressing a key.
Setting Description: Use the [Paper Store Cover] key to select the setting item. Each time
you press the [Paper Store Cover] key, the setting item changes to the next item, and the current
setting value of the item is printed out. Use the [FEED] key to select the setting value of the
setting item. Each time you press the [FEED] key, the setting value changes to the lower value
Settings：
Cover Cover Cover Cover
Cover Cover Cover Cover
Baud rate：
FEED FEED FEED
FEED FEED
FEED FEED FEED
Language：
FEED FEED
FEED
Print Font：
FEED
FEED
Print density：
FEED FEED
FEED
Printing Speed：
FEED FEED FEED
Baud
Density
Speed
Print Font
Language
Beeper
Out of paper
Black
China
English
12×24
9×17
Medium
Low
High
9600
57600
38400
19200
4800
115200
1200
2400
220mm/s
150mm/s
250mm/s
200mm/s
China-BIG5

15
FEED
Beeper：
FEED FEED FEED
FEED
Out of paper and reprint：
FEED
FEED
Black mark:
FEED
FEED
OFF
Cut ON
Error ON
ALL ON
OFF
ON
OFF
ON