Squareled BLADE 5 User manual

User Manual: Squareled Blade 5 48x10W RGBW

BLADE 5
48x10W - RGBW
USER MANUAL

1
INTRODUCTION
Thank you for having chosen our LED lighting
Unpack the device, inside the box you should find:
The fixture device
One power cable
One XLR connection cable
This manual
Please check carefully that there is no damage caused by
transportation. Should there be any problems, consult your dealer and
don’t install this device.
DESCRIPTION
Features
Easy multi fixture hanging system, outdoor version available
48pcs RGBW 4in1 LED, no ultraviolet radiation
More than 20,000 hours for the LED light source
15,000 lm
35 degrees
1/2/3/4/6/8F/9F/10F/10D/14D/15F DMX channels
16 Bit Dimmer
DMX Mode /Master-slave mode
AC 100-240V 50/60Hz 500W
Diecasting heatsink with fans control, convection cooling, With
temperature sensor to extend the lamp life
7000 Hz LED scan rate
L: 490mm H: 313mm W: 144mm
IP65
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to
maintain this condition and to ensure a safe operation, it
is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
This device falls under protection-class I. Therefore it is essential that

2
the device should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged,
it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.
Make sure that the available voltage is not higher than stated at the
end of this manual.
Make sure the power cord is never crimped or damaged by sharp
edges.
If this would be the case, replacement of the cable must be done by
an authorized dealer.
Always disconnect from the mains, when the device is not in use or
before cleaning it. Only handle the power cord by the plug. Never
pull out the plug by tugging the power cord.
Never look directly into the light source, as
sensitive persons may suffer an epileptic shock.
Important:
Damages caused by the disregard of this user manual are not
subject to warranty. The dealer will not accept liability for any
resulting defects or problems.
DMX-512 control connection
The product has a DMX 512 input fitted with 3-pin XLR connectors.
Screened cables in compliance with EIA RS-485 specifications and the
following characteristics must be used for connections:
- 2 conductors plus screen
- 120Ohm impedance
- low capacitance
- max. transmission rate 250kBaud.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is

3
in an electrically noisy environment, such as in a discotheque, it is
recommended to use a DMX terminator. This helps in preventing
corruption of the digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 OHM resistor connected
between pins 2 and 3,which is then plugged into the output XLR
socket of the last fixture in the chain.
Display Menu
Main menu
Sub-menu
Address
DMX Address Setting
Config.
Channel Mode
Channel 1Ch
Channel 2Ch
Channel 3Ch
Channel 4Ch
Channel 6Ch
Channel 8ChF
Channel 9ChF
Channel 10ChF
Channel 10ChD
Channel 14ChD
Channel 15ChF
Dimmer Curve
Set Curve Mode L
Set Curve Mode Q
Set Curve Mode I
Set Curve Mode S
Cipher Setup
0-999

4
Temp Unit CS
Celsius Degree
Fahrenheit Degree
DMX Status
Value Clear
Value Hold
Fan Speed
Normal/ middle/ fast
WDMX Mode
-
Display Mode
Disable
Enable
System Info
Temperature
Fixture Time
Color Menu
Red
0-255
Green
0-255
Blue
0-255
White
0-255
White Balance
Set Red
0-255
Set Green
0-255
Set Blue
0-255
Static color
Color 0-51
-
Auto Test
Effect Auto 01
-
Effect Auto 02
-
Effect Auto 03
-
Effect Auto 04
-
Fan Test
Fan 1
On/ Off
Auto speed
00 - 40
Load Default
Yes
No
Firmware
Version
Strobe Wash
Version 6.00

5
Main functions
1. Address: Current DMX address
A. Setting DMX address by button
press ENTER button when show the address menu, then adjust
the DMX address by pressing [UP] or [DOWN] button
Press [ENTER] to confirm or press [ESC] to return to main menu.
B. Setting DMX address by controller
1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26,
channel 7 to 30-36,channel 8 to 40-46,then the devices
connected to the controller will enter to the setting address mode
2. Set the DMX value of channel 1 from 0-59,then you will see
the first number of the Address change to (channel 1 value)/10.
For example, when set the value of channel 1 to 20,the first DMX
address number will be 2(20/10=2),
3. Set the DMX value of channel 2 from 0-99,then you will see
the second number of the Address change to (channel 2
value)/10.
For example, when set the value of channel 2 to 30,the first DMX
address number will be 2(30/10=3),
4.Set the DMX value of channel 3 from 0-99,then you will see the
third number of the Address change to (channel 3 value)/10.
For example, when set the value of channel 1 to 40,the first DMX
address number will be 3(40/10=4),
And the DMX address you set by controller will be 234.
5. Set the DMX value of channel 4 to 255,then you will save the
DMX address settled by the controller.
Caution: It won’t save the address if the address number is
over 512
6. set the value of channel 5-8 out of the value range show on the
step 1,and the device will exit the setting address mode
2. Config.
Setting DMX mode
press ENTER button when show the channel menu, then select
the DMX mode by pressing [UP] or [DOWN] button

6
Setting Dimmer Curve
press ENTER button when show the dimmer curve menu, then
select the dimmer curve by pressing [UP] or [DOWN] button
Setting Cipher
press ENTER button when show the cipher setup menu, then
setup cipher by pressing [UP] or [DOWN] button
Key mode
press ENTER button when show the key mode menu, then
select lock or unlock by pressing [UP] or [DOWN] button
Show Temperature
press ENTER button when show the Temp Unit CS menu, select
the way of showing the fixture’s temperature in ℃or ℉by
pressing [UP] or [DOWN] button
DMX status
press ENTER button when show the DMX Status menu, then
select clear value or hold value by pressing [UP] or [DOWN]
button
Display mode
press ENTER button when show the Display Mode menu, then
select auto or on by pressing [UP] or [DOWN] button
3. System info
Temperature
press ENTER button when show the Temperature menu, then it
will show the temperature of the fixture
Fixture time
press ENTER button when show the Fixture time menu, then it
will show how long time of the fixture already used
4. Color menu
press ENTER button when show the Color menu, press Enter
button to select the color mode, then adjust the color by pressing
[UP] or [DOWN] button
5. White balance

7
press ENTER button when show the white balance menu, press
Enter button to select the color mode, then adjust the color by
pressing [UP] or [DOWN] button
6. Auto test
press ENTER button when show the auto test menu, select test
mode by pressing [UP] or [DOWN] button
DMX functions and values
1 ch Mode
Ch
Value
Function
1
0-255
Static Color
2 ch Mode
Ch
Value
Function
1
0-7
8-15
16-151
152-175
175-199
200-244
245-255
Blackout
Shutter Open
Strobe
Fade In
Fade Out
Random Strobe
Shutter Open
2
0-255
Master Dimmer
3 ch Mode
Ch
Value
Function
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4 ch Mode

8
Ch
Value
Function
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
White
6 Ch Mode
Ch
Value
Function
1
0-7
8-15
16-151
152-175
175-199
200-244
245-255
Blackout
Shutter Open
Strobe
Fade In
Fade Out
Random Strobe
Shutter Open
2
0-255
Master dim
3
0-255
Red
4
0-255
Green
5
0-255
Blue
6
0-255
White
8 ChF Mode
Ch
Value
Function
1
0-255
Red
2
0-255
Fine Red
3
0-255
Green
4
0-255
Fine Green
5
0-255
Blue
6
0-255
Fine Blue
7
0-255
White
8
0-255
Fine White

9
9 ChF Mode
Ch
Value
Function
1
0-255
Master Dimmer
2
0-255
Red
3
0-255
Fine Red
4
0-255
Green
5
0-255
Fine Green
6
0-255
Blue
7
0-255
Fine Blue
8
0-255
White
9
0-255
Fine White
10 ChF Mode 16BIT
Ch
Value
Function
1
0-255
Master Dimmer
2
0-255
Fine Master Dimmer
3
0-255
Red
4
0-255
Red dimmer fine
5
0-255
Green
6
0-255
Green dimmer fine
7
0-255
Blue
8
0-255
Blue dimmer fine
9
0-255
White
10
0-255
White dimmer fine
10 ChD Mode
Ch
Value
Function
1
0-7
8-15
16-151
152-175
Blackout
Shutter Open
Strobe
Fade In

10
175-199
200-244
245-255
Fade Out
Random Strobe
Shutter Open
2
0-255
Master dim
3
0-255
Red1
4
0-255
Green1
5
0-255
Blue1
6
0-255
White1
7
0-255
Red2
8
0-255
Green2
9
0-255
Blue2
10
0-255
White2
14 ChD Mode
Ch
Value
Function
1
0-255
Master Dimmer
2
0-255
Red1
3
0-255
Green1
4
0-255
Blue1
5
0-255
White1
6
0-255
Red2
7
0-255
Green2
8
0-255
Blue2
9
0-255
White2
10
0-15
16-255
Shutter Open
Strobe From Slow To Fast
11
0-35
36-71
72-107
108-143
144-179
180-215
216-255
Shutter Open
Fade Out
Fade In
Fade In and Out
Fade By SIN Curve
Four Color Flow
Eight LEDs Flow
12
0-255
Static Color
13
0-255
Dimmer Speed

11
14
0-63
64-127
128-191
192-255
Linear
Square
Invert Square
S-Curve
15 ChF Mode
Ch
Value
Function
1
0-255
Master Dimmer
2
0-255
Fine Master Dimmer
3
0-255
Red1
4
0-255
Green1
5
0-255
Blue1
6
0-255
White1
7
0-255
Red2
8
0-255
Green2
9
0-255
Blue2
10
0-255
White2
11
0-15
16-255
Shutter Open
Strobe From Slow To Fast
12
0-35
36-71
72-107
108-143
144-179
180-215
216-255
Shutter Open
Fade Out
Fade In
Fade In and Out
Fade By SIN Curve
Four Color Flow
Eight LEDs Flow
13
0-255
Static Color
14
0-255
Dimmer Speed
15
0-63
64-127
128-191
192-255
Linear
Square
Invert Square
S-Curve

12
CLEANING AND MAINTENANCE
We recommend a frequent cleaning of the device. Please use a soft
lint-free and moistened cloth. Never use alcohol or solvents!
CAUTION!
Disconnect from mains before starting maintenance
operation.
There are no serviceable parts inside the device. Maintenance and
service operations are only to be carried out by authorized dealers.
If you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to
be replaced by authorized dealers only in order to avoid hazards.
If you have further questions, please contact your dealer.
INSTALLATION
The device must only be installed at a vibration-free, oscillation-free
and fire-resistant location.

Das Lichttechnikhaus Vertriebs GmbH
Rudolf-Diesel-Str. 3, D-89312 Günzburg
Telefon [phone]
Fax [phone]
E-Mail [email protected]
Web www.lth-gmbh.de