Ssl ML46DB User manual

ii
CONTENTS
Precautions................................................................................................................................................. 1
Use Caution
..............................................................................................................................
1
Lithium Battery Cell Warnings
s ..........................................................................................................................................1
Installation .................................................................................................................................................. 2
Installation Procedures .......................................................................................................................... 2
Installation Opening................................................................................................................................ 2
Uninstall the Main Unit
...........................................................................................................................3
Wiring Connections................................................................................................................................ 3
Control Panel Button Locations.................................................................................................................. 4
Operation ................................................................................................................................................... 4
Power .....................................................................................................................................................
4
4
Adjust Volume (VOL)
........................................................................................................
.................................................................................................................
4
.............................................................................................................................. 5
Set the Clock (CLK)
Change the Source (MODE)
............................................................................................................................. 5
Reset System (RESET)
................................................................................................................... 5
..................................................................................................................... 6
Adjust Menu Options (SEL)
.................................................................................................................. 6
Change Bands (BAND).......................................................................................................................... 6
Manual Tuning (|<< / >>|)
........................................................................... 6
6
Auto Seek Tuning (|<< / >>|)
...................................................................................................................................................... 6
Automatic Store Station / Preset Station Scan (AMS)
Mute
......................................................................................................................................................... 6EQ
.............................................................................................................................................
..........................................................................................................................................
6
Store/Recall Preset Stations (1 - 6)
.......................................................................................................................................... 6
.......................................................................................................................................6
Insert USB
AUX In Jack
Release Panel
......................................................................................................................... 6
Track Search
Remote Control
......................................................................................................................................... 8
Troubleshooting.........................................................................................................................................
10
............................................................................................................................................
11
Bluetooth Operation.................................................................................................................................... 7
Pair and Connect ................................................................................................................................... 7
Make a Call ............................................................................................................................................ 7
Redial Last Dialed Number ................................................................................................................... 7
Answer a Call......................................................................................................................................... 7
Reject or End a Call ............................................................................................................................... 7
Switch Audio Between Car and Phone .................................................................................................. 7
Adjust Talk Volume................................................................................................................................. 7
Audio Stream (A2DP) ............................................................................................................................ 7
5
5
..............................................................................
Play/Pause, Intro, Repeat, Random, Tracks playback
Track/Folder Navigation
6
6
...............................................................................................................................
........................................................................................................................
.........................................................................................................................
Next/Previous Track
Fast Forward/Backward
Remove Insulating Sheet....................................................................................................................... 8
Replace Lithium Battery Cell.................................................................................................................. 8
Remote Control Operation ..................................................................................................................... 8
Button Names and Locations................................................................................................................. 9

PRECAUTIONS
Lithium Battery Cell Warnings
• Cell leakage may cause damage to the remote control.
• Do not throw cells into as this may cause an explosion.
• Keep battery cells out of reach of children.
Use cautions
•
•
•
•
•
•
•
• Be sure to lower the volume before switching off the unit or the ignition key.
Some MP3/WMA files may not be playable.
1

INSTALLATION
2
Installation Procedures
Installation Opening
First complete the electrical connections and then check for correctness.
This unit can be installed in any dashboard Having an opening as shown below.
Insert mounting collar into the dashboard and bend the mounting tabs out with a screwdriver.
Make sure that lock lever is flush with the mounting collar( not projecting outward).
2.05 inch
7.20 inch
MOUNTING SLEEVE

INSTALLATION(CONT.)
3
- Only use speakers with 4 ohms impedance.
- Do not attach the control panel to the chassis before wiring is complete.
- The maximum current of the auto antenna is 200mA.
Wiring Connections
!
Uninstall the Main Unit
1. Remove the plastic trim out from the main unit.
2. Insert a bracket key into the left and right side of the main unit and draw the unit out of
the mounting sleeve.
WIRING
DIAGRAM
CAUTION
+12V DC
NEGATIVE
GROUND
15
White:Front Left PRE-AMP Output
White: Rear Left PRE-AMP Output
Red: Front Right PRE-AMP Output
Red: Rear Right PRE-AMP Output
Radio Antenna
15A
Purple +
Rear Left Speaker
Front Left Speaker
White +
Green +
Green/Black -
White/Black -Gray/Black -
Gray +
Front Right Speaker
Purple/Black -
Rear Right Speaker ACC + (Red)
GND - (Black)
ANT + (Blue)
Power B + (Yellow)

CONTROL PANEL BUTTON LOCATIONS
4
OPERATION
REMOVE PANEL
the unit).
Note:
1.POWER
2.MODE
3-8.
flash drive, their respective logos will illuminate on the display.
Press the power ( ) button to turn the unit on or off.
Press the MODE button to switch between RADIO, USB, BT, AUX IN modes. (if there are USB inside
radio , BT and Aux in. When the user insert a USB flash drive
RESET

OPERATION
5
9. CLK
Press the CLK button once to display the real time, With time appearing on the display.Press and hold
CLK button for more than 2 seconds until the hour flashes. You can adjust the HOUR by pressing the
button and button. Then press the CLK button briefly, the minute will flash, you can adjust the
MINUTE by pressing the button and button.
Finally press the CLK button to confirm the time adjustments.
During USB mode, press the ‘1/>||’ button to pause or resume music playback.
Press the ‘2/INT’ button to play the first 10 seconds of each track, press again to stop the introduction
scan, and play the current track.
Press the ‘3/RPT’ button to toggle between RPT ALL (Play all track), RPT FLR (Continuously repeats all
tracks in current folder) and RPT ONE (Continuously repeats current track).
Press the ‘4/RDM’ button to play all tracks in random order, press again to cancel random playback.
Rotate the volume knob to increase or decrese the volume level of the sound output.
Press the SEL button on the front panel or on the remote control repeatedly to cycle through the
following adjustable audio functions: ILL MID/HI/LOW, BASS, TREBLE, BALANCE, FADER, EQ OFF,
CLASS/ROCK/POP/ FLAT, LOUD ON/OFF, DX/LOC, STEREO/MONO, CLOCK 12/24, AREA US/EU.
- ILL MID/HI/LOW: This receiver is equipped with 3 brightness settings.
Rotate the volume knob to preset the illumination to middle, high or low.
- BASS: -7,-6, ~, -1,0,+1,~, +6,+7
- TREBLE: -7,-6,~, -1,0,+1,~,+6,+7
- BALANCE: L7,L6,~,L1, 0, R1,~, R6, R7
- FADER: R7,R6~,R1, 0, F1,~,F6, F7
- EQ(Equalizer) Setting: OFF, CLASS, ROCK, POP, FLAT
- Loudness: LOUD ON/OFF
- DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).
- Stereo/Mono: Switches between MONO and STEREO reception mode for radio frequencies.
- CLOCK 12/24: Select between 12 hours and 24 hours display.
Note: If 12 hour display is selected , AM= Morning; PM= Afternoon
- AREA US/EU: This car radio is equipped the USA / Europe frequency.
Rotate the volume knob to switch between USA and Europe frequency.
The system will change the frequency setting in about 3 seconds.
• Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on the remote control
to adjust the selected item.
Adjust Volume and Menu Options (SEL)
10.

OPERATION
6
16. EQ
Press the EQ button to choose a desired preset equlizer mode: OFF, CLASS, ROCK, POP, FLAT.
11.FF( ) &12.FB( )
In the radio mode:
Long press the or button for more than 2 seconds, the unit will switch to manual tuning
mode, briefly press the or button to search the next or previous frequency step by step.
Short press the or button, the automatic search will start, it will search upward or downward
for the strong signal radio station within the cuttent band. The auto searching will stop until find a
station.
19.
15. MUTE
17. USB PORT
18. AUX IN JACK
20. RESET
To reset all parameters to factory default values. Press the button to detach the control panel form
the head unit and remove the control panel,then use a subject with a sharp point end to thrush the RESET
hole.
flash on the LCD
detach
13.BAND
14.AMS
In radio mode,short press the BAND button repeatedly to select the one of the radio band : FM 1, FM2,
FM 3, AM1,AM2 in a cycle sequence. When you select a band, the word F1、F2、F3 for FM band,
and A1, A2 for AM band will be shown on the LCD display.
preset station in each band.
AMS button to scan each
Press the AMS check
Press the AMS button to enter track search mode, the “TRK0000” will appear on the display.
Rotate VOL knob to select the “first number”. Then press the button to move the “first number” to
the left and enter the next number. Finally press the SEL button to confirm and play the selected track.
If no any operation in 5 seconds,it will play the current track.
When the 6 strongest stations will be stored into
In the USB mode:
Briefly press the or button to play the the next or previou track.
Press and hold the or button to fast forward or fast backward.
In radio mode:
In USB playback mode:

BLUETOOTH OPERATION
Pair and Connect
Prior to using the Bluetooth device as a handsfree system for a Bluetooth-enabled mobile
phone for the time, you must pair and connect the two devices as follows:
1. In any mode, prior to pairing and connecting, the BT logo in the LCD indicating
that no device is connected. To begin pairing, enable BT mode on your mobile phone.
2. When the phone the car audio system, the “SSL ML46DB” will be displayed.
3. Choose the SSL ML46DB from the device list to pair and connect with the car audio
system. Upon the BT logo will stop
4. When pairing is complete, the mobile phone audio will automatically transfer to the car
audio system whenever a call is made or received, or when the mobile phone plays
music.
7
Make a Call
• To make a call, dial the call directly from the paired mobile phone.
• To make a call with this Bluetooth handsfree system.
a) When linking up the Bluetooth mobile phone to this car audio handsfree system, press
the button to access the dial telephone number mode, then press the “0~9”, * and #
button on the remote control to input the telephone number, the entered number will be
shown on the LCD.
b) If a number has been incorrectly input, press the DEL button or button to delete it.
c) Press the button to make outgoing call.
Redial Last Dialed Number
Press and hold the button on the control panel to redial the last dialed phone number.
Answer a Call
•When the mobile phone is called, the incoming telephone number displays in the LCD.
•To receive the call, press the button on the control panel or remote control.
To reject the call or end an active call, press the button.
Reject or End a Call
Switch Audio Between Car and Phone
During a call, press the VOL knob/button to switch the audio source from the car audio
system back to your mobile phone.
Adjust Talk Volume
•During a call, use VOL knob or VOL + and VOL - buttons to adjust the volume level.
•Use the MUTE button to mute sound.
Audio Streaming (A2DP)
1. Press the MODE button to enter BT mode and display pause in the LCD.
2. When a mobile device is paired, music played through that device will automatically be
heard through the car audio system.
3. Press the >>| or |<< button to play the next or previous on the mobile phone.
4. Press the >|| button to pause or resume music playback.

8
REMOTE CONTROL
Remove Insulating Sheet
The remote control comes with an insulating sheet
attached to the underside of the remote control, as
illustrated on the right. The remote control will not
work until the insulating sheet is removed.
Replace Lithium Battery Cell
1. When the lithium cell battery becomes weak,
replace it as illustrated on the right.
2. Press and hold the movable block in the
direction indicated by arrow 1. At the same
time, pull the cell holder out of the remote
control in the direction indicated by arrow 2.
3. Replace the old cell with a new one, making
sure the (+) polarity is facing upward.
4. Re-insert the cell holder into the remote
control.
- Cell leakage may cause damage to the remote control.
- Do not throw cells into as this may cause an explosion.
- Keep battery cells out of reach of children.
Remote Control Operation
Position the emitting window of the remote control
toward the sensor window of the unit.
• The operation angle for front panel remote control
reception is about 30 degrees.
• The distance between the emitting window of the remote control and the sensor window
of the unit should remain less than 5 meters.
!