Stanley PC509 User manual

14
• Coloque el convertidor lo más lejos posible de la televisión, de la antena y de los cables de la antena. Utilice un cable de extensión, en caso de
necesidad.
• Reajuste la orientación del convertidor, de los cables de la antena y del cable eléctrico de la TV para reducir al mínimo interferencia.
• Cerciórese de que la antena que alimenta la televisión proporcione (“nieve libre ") una señal adecuada y esa alta calidad, cable blindado de la
antena está utilizada.
• No utilice el convertidor para funcionar aplicaciones de alta potencia o las herramientas al mismo tiempo usted lo está utilizando para funcionar
la TV.
Problemas frecuentes de potencia de salida
El voltaje de entrada está por debajo de 10,5 voltios
Recargue la batería auto o compruebe la fuente de CC.
El equipo que se opera genera mucha energía
Reduzca la carga a un máximo de 500 vatios.
El convertidor está en la condición de apagado térmico
Espere que el convertidor se enfríe. Asegúrese de que haya una ventilación adecuada alrededor de la unidad y que la carga no sea mayor a 500
vatios para un funcionamiento continuo.
La salida de CA está en cortocircuito
Desenchufe la aplicación de la CA. Apague el convertidor. Desconecte la unidad de cualquier fuente de la potencia CC de 12 voltios. Compruebe la
cuerda de la aplicación.
ACCESORIOS
Los accesorios que se recomiendan para la herramienta están disponibles en su distribuidor local o en el centro de mantenimiento autorizado. Si
necesita asistencia en relación con los accesorios, por favor contacto fabricante en [phone].
ADVERTENCIA: El uso de cualquier accesorio no recomendado para el uso con esta aplicación podía ser peligroso.
INFORMACIÓN DE SERVICIO
Si usted necesita asesoramiento técnico, reparación, o una verdadera fábrica piezas de recambio, contacto con el fabricante en [phone].
UNA GARANTÍA LIMITADA DEL AÑO
Fabricante garantiza este producto durante un año contra cualquier defectos en los materiales o mano de obra. El producto defectuoso será
reemplazado o reparado en ningún cargo en cualquiera de dos maneras.
La primera opción, el reemplazo, es devolver el producto al comercio donde se lo adquirió (siempre y cuando se trate de un comercio participante).
Las devoluciones deben realizarse conforme a la política de devolución del comercio (generalmente, entre 30 y 90 días posteriores a la venta).
Prueba de compra puede ser necesaria. Consulte en el comercio acerca de la política especial sobre devoluciones una vez excedido el plazo
establecido. La segunda opción es devolver el producto (pagados) al fabricante de reparación o sustitución en nuestra opción. Prueba de compra
puede ser necesaria.
Esta garantía no se extiende a los accesorios. Esta garantía le concede derechos legales específicos; usted puede tener otros derechos que pueden
variar según el estado o la provincia. Este producto no está diseñado para uso comercial.
ESPECIFICACIONES
Energía máxima: 500 vatios de continuo
Voltaje de entrada: 12,5 voltios de CC, 48 amperios
Voltaje de salida: 110-125 voltios de CA, 60Hz
Forma de onda de la salida: Onda de seno modificada
USB: 5VCC, 500mA
Fusible de enchufe de la CC: 10A/250V
Importados por
Baccus Global
399 NW 2nd Avenue, Suite 150
Boca Raton, FL 33432
[phone] RD042809
500 WATT POWER CONVERTER
INSTRUCTION MANUAL
500 WATT CONVERTIDOR DE PODER
MANUAL DE INSTRUCCIÓN
SAVE THIS INSTUCTION MANUAL FOR FUTURE REFERENCE.
CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.
© 2009 Baccus Global
Boca Raton, FL 33432
Customer Service: [phone]
PC509
English page 3
Español pagina 9
PC509_ManualENSP_042809.qxp 4/28/2009 11:42 AM Page 14

2 3
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating converter. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal
injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are
certain applications for which tools and equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/or
used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool
or equipment.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth defect or other
reproductive harm. Wash hands after handling.
• Avoid dangerous environments. Don’t use converters in damp or wet locations.
• Keep children away. Keep away from children. This is not a toy!
• Store indoors. When not in use, converters should be stored indoors in dry, and high or locked-up places – out of reach of children.
• Disconnect the converter from the power supply when not in use.
• Proper cooling is essential when operating the converter. Do not place it near a vehicle’s heat vent or in direct sunlight.
• Use of accessories and attachments:The use of any accessory or attachment not recommended by manufacturer for use with this converter
could be hazardous.
• Stay alert. Use common sense. Do not operate converter when you are tired.
• Check for damaged parts. Any part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise
indicated elsewhere in this instruction manual before further use.
• Do not operate the converter near flammable liquids or in gaseous or explosive atmospheres. Motors in tools or appliances used with the
converter may spark, and the sparks might ignite fumes.
SPECIFIC SAFETY INSTRUCTIONS FOR CONVERTERS
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Do not connect to AC distribution wiring.
• Do not make any electrical connections or disconnections in areas designated as IGNITION PROTECTED. This converter is NOT approved for ignition
protected areas.
• Never immerse the converter in water or any other liquid, or use when wet.
• Do not insert foreign objects into the converter’s outlets.
WARNING: TO REDUCE THE RISK OF FIRE:
• Do not operate near flammable materials, fumes or gases.
• Do not expose to extreme heat or flames.
• If the vehicle accessory outlet fuse opens (blows) when plugging in this converter, do not use this converter with this vehicle accessory outlet:
Do not repeatedly replace the fuse.
Do not replace the vehicle accessory outlet fuse with one of a higher amperage rating.
Never attempt to patch the fuse with tin foil or wire.
Any of these actions may cause serious electrical damage and/or a fire.
This converter is rated to draw 10 amperes from a 13.8V vehicle outlet. Ensure that the engine system in your vehicle can supply sufficient
energy to the converter without causing the vehicle accessory outlet fuse to open. The fuse must be rated higher than 12 amps. Information on
the vehicle accessory fuse ratings are typically found in the vehicle operator’s manual.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Disconnect appliance plug from converter outlet before working on the appliance.
• Do not attempt to connect or set up the converter or its components while operating your vehicle. Not paying attention to the road may result in
a serious accident.
• Always use the converter where there is adequate ventilation. Do not block ventilation slots.
FEATURES
CARACTERÍSTICAS
FEATURES
1. Ventilation slots
2. Power/fault LED indicator
3. USB power port
4. On/Off button
5. Mounting brackets (total of 4, 2 in front, 2 in back)
6. Three-prong 120 volt AC outlets
7. Red (positive) cable post
8. High-speed cooling fan
9. Black (negative) cable post
10. 12 volt DC vehicle adapter plug with“O” ring connectors
11. Battery clips with cables and“O”ring connectors
CARACTERÍSTICAS
1. Ranuras de ventilación
2. Indicador LED de potencia y fallas
3. Puerto de la energía USB
4. Botón con./desc. (on/off)
5. Consolas de montaje (total de 4, 2 en frente, adentro parte
posterior 2)
6. Tomacorrientes de tres patas de CA de 120 voltios
7. Poste del cable rojo (positivo)
8. Ventilador de enfriamiento de alta velocidad
9. Poste del cable negro (negativo)
10. Enchufe para adaptador de vehículo de 12 voltios de CC con los
conectadores del anillo de“O”
11. Clips de la batería con los cables y los conectadores del anillo
de“O”
2
3
4
6
7
1
3
6
9
10 11
8
5
PC509_ManualENSP_042809.qxp 4/28/2009 11:42 AM Page 2

5
CAUTIONS
• If turning the On/Off switch off, then on again does not reset the converter, DO NOT ATTEMPT TO OPEN THE CONVERTER. Opening the converter
for any reason will void the warranty. The unit must be returned to manufacturer for testing and repair by professional factory technicians.
• Exceeding recommended voltage limits will void manufacturer’s warranty.
• NEVER try to use your converter with any 12 volt DC power source that uses a positive ground. (Most vehicles and boats use negative ground
systems.)
• The Power Converter must be connected only to batteries with a nominal output voltage of 12 volts. The unit will not operate from a 6 volt
battery and will sustain permanent damage if connected to a 24 volt battery.
• Reverse polarity connection will result in a blown fuse and may cause permanent damage to the converter.
Protective Features
The converter monitors the following conditions:
Input Voltage Too Low: This condition is not harmful to the converter, but could damage the power source, so the converter will automatically
shut down when input voltage drops below 10.5 ± 0.3 volts DC.
Input Voltage Too High: The converter will automatically shut down when DC input voltage exceeds 15.4 ± 0.3 volts, as this can harm the unit.
Thermal Shutdown Protection: The converter will automatically shut down when the unit becomes overheated.
Overload/Short Circuit Protection: The converter will automatically shut down when an overload or short circuit occurs.
Note: The Power/Fault LED Indicator will light solid to indicate that the converter is properly connected. The Power/Fault LED Indicator will flash to warn of a fault
condition before automatic shutdown occurs.
RATED VERSUS ACTUAL CURRENT DRAW OF EQUIPMENT
Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the power consumption in amps or watts.
Be sure that the power consumption of the item to be operated is below 500 watts. If the power consumption is rated in amps AC, simply multiply
by the AC volts (120) to determine the wattage.
Resistive loads are the easiest for the converter to run; however, it will not run larger resistive loads (such as electric stoves and heaters), which
require far more wattage than the converter can deliver on a continuous basis. Inductive loads (such as TVs and stereos) require more current to
operate than do resistive loads of the same wattage rating.
For safety reasons, the converter will simply shut down if it is overloaded. To restart the unit, simply unplug all devices plugged into the converter;
disconnect the converter from any 12 volt DC power source; then reconnect the converter BEFORE plugging the appliance(s) back in.
INSTALLATION
Your converter will provide you with continuous electrical power when powered by a reliable 12 volt DC source, such as a vehicle battery or a
multiple battery configuration. This manual does not describe all of the possible configurations.
Mounting the Converter
The converter comes equipped with mounting brackets for long-term installation. Secure the converter using screws appropriate to the mounting
surface (not supplied). Use ONLY non-corrosive marine fasteners and fittings for marine installation.
CAUTION
To avoid the risk of property damage, only mount the converter on a level, stable surface, assuring that all screws are tightened securely and
observing all of the cautions and recommendations regarding installation found in this manual.
Operating Environment
For best operating results, your converter should be placed on a flat surface, such as the ground, car floor or seat, or other solid surface to help
diffuse the heat that is generated. Position the converter as close to the DC power source as possible.
The converter should only be operated in locations that meet the following criteria:
DRY – Do not allow water and/or other liquids to come into contact with the converter.
COOL – Ambient air temperature should be between 30°F (–1°C) non-condensing and 105°F (40°C). Do not place the converter on or near a
heating vent or any piece of equipment that is generating heat above room temperature. Keep the converter out of direct sunlight.
VENTILATED – Allow at least three inches of clearance from other objects to ensure free air circulation around the converter. Never place items on
or over the converter during operation.
SAFE – Do not locate converters in an area, room or compartment where explosives or flammable fumes might be present, such as engine rooms,
engine compartments, and boats or small, unvented battery compartments.
Marine Applications
DO NOT install the converter below or near the waterline, and keep the converter away from moisture and water. The unit’s housing is moisture-
resistant (NOT waterproof).
ONLY install the converter on a level, stable surface where it is not likely to fall or be knocked over; and is not subject to vibration.
Use ONLY non-corrosive marine fasteners and fittings for installation.
4
• Always turn the converter off and disconnect it from the power source when not in use.
• The converter must be connected only to batteries with a nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery and
will sustain permanent damage if connected to a 24 volt battery.
• When using this unit in a vehicle, check the vehicle owner’s manual for maximum power rating and recommended output. Do not install in
engine compartment — install in a well ventilated area.
• Do not use with positive ground electrical systems.* Reverse polarity connection will result in a blown fuse and may cause permanent damage to
the converter and will void warranty.
*The majority of modern automobiles, RVs and trucks are negative ground.
• Keep in mind that this converter will not operate high wattage appliances or equipment that produce heat, such as hair dryers, microwave ovens
and toasters.
• DO NOT OPEN THE CONVERTER — there are no user-serviceable parts inside. Opening the converter will void manufacturer’s warranty.
• Do not use this converter with medical devices. It is not tested for medical applications.
• Install and operate converter only as described in this Instruction Manual.
SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Follow these instructions and those published by battery
manufacturer and the manufacturer of any equipment you intend to use with this unit. Review cautionary markings on these products and
on engine.
INTRODUCTION
Congratulations on purchasing your new converter. Read this Instruction Manual and follow the instructions carefully before using your
new converter.
This power converter is configured to supply continuous power in the form of two 120 volt AC outlets and a 5 volt USB charging port to run most
household or electronic appliances.
HOW THIS CONVERTER WORKS
This converter is an electronic device that converts low voltage DC (direct current) electricity from a battery to 120 volts AC (alternating current)
household power. It converts power in two stages. The first stage is a DC-to-DC conversion process that raises the low voltage DC at the converter
input to 145 volts DC.The second stage is a MOSFET bridge stage that converts the high voltage DC into 120 volts, 60 Hz AC.
Power Converter Output Waveform
The AC output waveform of this converter is known as a modified sine wave. It is a stepped waveform that has characteristics similar to the sine
wave shape of utility power. This type of waveform is suitable for most AC loads, including linear and switching power supplies used in electronic
equipment, transformers, and small motors.
CAUTION: RECHARGEABLE DEVICES
• Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle. These devices may damage the
converter or the charging circuit.
• When using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine if it produces excessive heat.
• If excessive heat is produced, this indicates the device should not be used with this converter.
• This problem does not occur with most of the battery-operated equipment. Most of these devices use a separate charger or transformer that is
plugged into an AC receptacle.
• The converter is capable of running most chargers and transformers.
POWER SOURCE AND PROTECTIVE FEATURES
Power Source Requirements
Your converter will operate from input voltages between 11 and 15 volts DC. If the input voltage drops below 10.5 volts DC, the converter will shut
down. This feature protects the battery from being completely discharged.
The converter will also shut down if the input voltage exceeds 15.4 volts. This protects the converter against excessive input voltage. Although the
converter has built-in protection against over voltage, it may still be damaged if the input voltage exceeds 15 volts.
Your converter is engineered to be connected directly to standard electrical and electronic equipment in the manner described in the“Installation”
section of this Instruction Manual. Do not connect the converter to household or RV AC distribution wiring. Do not connect the converter to any AC
load circuit in which the neutral conductor is connected to ground (earth) or to the negative of the DC (battery) power source.
Inductive loads, such as TVs and stereos, require more current to operate than resistive loads of the same wattage rating. Induction motors, as well
as some TVs, may require two to six times their rated wattage to start up. Because these converters have a peak watt power rating, many such
appliances and tools may be safely operated.The equipment that needs the highest starting wattage are pumps and compressors that start under
load. This equipment can be safely tested. If an overload is detected, the converter will simply shut down until the overload situation is corrected.
Use the front panel switch to turn off the converter, then on again to reset it.
PC509_ManualENSP_042809.qxp 4/28/2009 11:42 AM Page 4

7
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Always connect the converter to the 12 volt DC power source before plugging any devices into the unit.
The standard North American 120 volt AC and USB outlets allow simultaneous operation of multiple devices. Simply plug the 110/120 volt AC
appliance into one of the converter’s three-prong AC outlet and/or plug the USB-powered device into the converter’s USB charging port and
operate normally.
Notes: Ensure that the wattage of all equipment simultaneously plugged into the converter does not exceed 500 watts continuous.
If the converter does not work when using the vehicle accessory outlet, make sure the ignition/accessory switch is actually powering the accessory outlet.
Some vehicles require the ignition switch to be turned on.
The converter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and toasters.
This converter’s USB Charging Port does not support data communication. It only provides 5 volts/500mA DC power to an external USB-powered device.
Remember to turn the unit off and disconnect from any power source when it is not in use.
CARE AND MAINTENANCE
Storage
1. Ideal storage temperature range is 0-40°C (32-104°F).
2. Store and use the converter in a cool, dry place with adequate ventilation for all-around air circulation.
3. Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or dampness.
Fuse Replacement (in Vehicle Accessory Outlet Plug)
If the converter is overloaded, and the green LED is not lit, the internal 10 amp fuse may be blown.
1. Unscrew the flange of the plug (counterclockwise).
2. Remove the end contact, flange and fuse.
3. Inspect the fuse to see if it is good or blown.
4. Replace with a new 10 amp fuse, if needed.
5. Carefully reassemble the fuse, end contact and flange. Do not overtighten the flange (clockwise).
TROUBLESHOOTING
Common Audio Problems
Buzzing Sound In Audio Systems
Some inexpensive stereo systems and boom boxes make a buzzing sound when operated from the converter, because the power supply in the
electronic device does not properly filter the modified sine wave produced by the converter. The only solution to this problem is to use a sound
system that has a higher quality power supply.
Television Interference
The converter is shielded to minimize interference with TV signals. However, in some instances, some interference may still occur, particularly
where TV signals are weak. Try the following corrective measures:
• Place the converter as far as possible from the television, the antenna and the antenna cables. Use an extension cable, if necessary.
• Readjust the orientation of the converter, the antenna cables and the TV power cord to minimize interference.
• Make sure the antenna feeding the television provides an adequate (“snow free”) signal and that high quality, shielded antenna cable is used.
• Do not use the converter to operate high-power appliances or tools at the same time you are using it to operate the TV.
Common Power Output Problems
Input voltage below 10.5 volts
Recharge auto battery or check DC power supply.
Equipment being operated draws too much power
Reduce load to maximum 500 watts.
Converter in thermal shutdown condition
Allow converter to cool down. Ensure there is adequate ventilation around the unit and that the load is no more than 500 watts for continuous
operation.
AC output is shorted
Unplug the AC appliance. Turn off the converter. Disconnect the unit from any 12 volt DC power source. Check the appliance cord.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding
accessories, please contact manufacturer at [phone].
WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at [phone].
6
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR PROPERTY DAMAGE
In all marine applications, always observe the directions given above, as well as those listed in the Important Safety Instructions of this manual.
Connecting to a Power Source Using the 12 Volt DC Vehicle Adapter Plug with “O” Ring Connectors
The DC Accessory Outlet Plug is suitable for operating the converter at power outputs up to 100 watts.
1. Check to make sure the converter’s On/Off switch has been turned off (the power/fault LED is not lit).
2. Turn the red plastic cap (counterclockwise) on the converter’s positive (+) cable post and remove. Attach the positive “O”ring at the end of the
red 12 volt DC vehicle adapter cable. Replace the cap and turn clockwise to secure. Do not over-tighten.
3. Turn the black plastic cap on the converter’s negative (–) cable post counterclockwise and remove. Attach the negative“O”ring at the end of
the black 12 volt DC vehicle adapter cable. Replace the cap and turn clockwise to secure. Do not over-tighten.
4. Connect the 12 volt DC vehicle adapter plug to a vehicle’s accessory outlet or other 12 volt DC power source. Make sure there is adequate space
for proper ventilation of the converter.
5. Rotate the unit slightly to make sure there is good contact.
CAUTIONS
• Connect directly to power source using the included Battery Clips when operating above 100 watts.
• Do not use with positive ground electrical systems.
• Reverse polarity connection will result in a blown fuse and may cause permanent damage to the converter.
Note: Most vehicle accessory outlet circuits have fuses rated at 15 to 20 amps or greater. To operate at full wattage, either use the supplied battery clips or directly
wire to the power source with wire and fuse (NOT SUPPLIED).
Connecting to a Power Source Using the Supplied Battery Clips with “O” Ring Connectors
Use the provided battery clips (with cables and “O”ring connectors) to connect the converter directly to the 12 volt power source as follows:
1. Check to make sure the converter’s On/Off switch has been turned off (the power/fault LED is not lit) and that no flammable fumes are present
in the installation area.
2. Turn the red plastic cap (counterclockwise) on the converter’s positive (+) cable post and remove. Attach the positive “O”ring at the end of the
red battery clip cable. Replace the cap and turn clockwise to secure. Do not over-tighten.
3. Turn the black plastic cap (counterclockwise) on the converter’s negative (–) cable post and remove. Attach the negative“O”ring at the end of
the black battery clip cable. Replace the cap and turn clockwise to secure. Do not over-tighten.
4. Make sure that all connections between cables and terminals are secure.
Direct Hardwiring to Power Source (optional connection method; hardware not included)
Use #10 AWG wire if the converter to power source connection is 10 feet or less. For longer cable lengths use #8 AWG wire. In either case, protect
the positive (+) wire from shorts by installing a 50 amp fuse or circuit breaker close to the DC power source (battery) terminal.
PROCEDURE
1. Check to make sure the converter’s On/Off switch has been turned off (the power/fault LED is not lit) and that no flammable fumes are present
in the installation area.
2. Identify the positive (+) and negative (–) DC power source (battery) terminals.
3. Install a fuse holder or breaker close to the positive (+) terminal of the DC source (battery).
4. Connect a length of wire on one side of the fuse holder or circuit breaker. Connect the other end of the wire to the positive (+) terminal of the
converter.
5. Connect a length of wire between the converter’s negative (–) terminal and the DC power source negative (–) terminal.
6. Connect a short length of wire to the other terminal of the fuse holder or circuit breaker. Mark it “positive”or“+”.
7. Connect the free end of the fuse or breaker wire to the positive (+) terminal of the DC power source (battery).
8. Insert a fuse appropriate to the converter in the fuse holder.
9. Test the converter by turning it on and plugging in a 100 watt lamp or equipment.
10. If the converter is not properly operating, then refer to the“Troubleshooting”section of this manual.
CAUTIONS: TO REDUCE THE RISK OF PROPERTY DAMAGE
• Loose connectors may cause overheated wires and melted insulation.
• Check to make sure you have not reversed the polarity. Damage due to reversed polarity is not covered by manufacturer’s warranty.
IMPORTANT CABLE INFORMATION
Substantial power loss and reduced battery operating time results from converters installed with cables that are not able to supply full power.
Symptoms of low battery power can result from cables that are either excessively long or an insufficient gauge. Marine installations are also
subjected to vibration and stresses that exceed those of other mobile installations.Therefore, the installer/operator should be especially aware of
the requirements to maintain secure, tight, water-resistant electrical connections and to provide for strain relief for DC cables and appliance
wiring. Cable insulation must be the appropriate type for the environment.
OPERATING INSTRUCTIONS
The power/fault LED indicator lights solid when the converter is properly connected to a functioning DC power source. The AC and USB outlets are
ready to use. (If the power/fault LED indicator flashes, refer to the Troubleshooting Section of this Instruction Manual.)
PC509_ManualENSP_042809.qxp 4/28/2009 11:42 AM Page 6

9
ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD GENERALES
LEA LAS INSTRUCCIONES
ADVERTENCIA: Lea todas las instrucciones antes de operar el convertidor. El incumplimiento de todas las instrucciones
enumeradas a continuación puede provocar una descarga eléctrica, un incendio o lesiones graves.
NORMAS DE SEGURIDAD / DEFINICIONES
PELIGRO: Indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves.
ADVERTENCIA: Indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves.
PRECAUCIÓN: Indica una situación de peligro potencial que, si no se evita, puede provocar lesiones leves o moderadas.
PRECAUCIÓN: Utilizado sin el símbolo de alerta de seguridad indica una situación de peligro potencial que, si no se evita, puede provocar daños
en la propiedad.
RIESGO DE OPERACIÓN INSEGURA. Cuando se utilizan herramientas o equipos, siempre se deben respetar las precauciones de seguridad para
reducir el riesgo de lesiones personales. La operación, el mantenimiento o la modificación incorrectos de herramientas o equipos pueden provocar
lesiones graves y daños a la propiedad. Las herramientas y los equipos están diseñados para determinados usos. Fabricante recomienda
encarecidamente que NO se modifique este producto y que NO se utilice para ningún otro uso que aquél para el que fue diseñado. Lea y
comprenda todas las instrucciones operativas y las advertencias antes de utilizar cualquier herramienta o equipo.
INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD
ADVERTENCIA: Este producto o su cable de alimentación contiene plomo, una sustancia química reconocida por el Estado de California como
causante de cáncer, defectos de nacimiento u otros problemas reproductivos. Lávese las manos después de utilizarlo.
• Evite las condiciones ambientales peligrosas. No utilice artefactos en zonas húmedas o mojadas. No utilice artefactos bajo la lluvia.
• Mantenga a los niños ausentes. Guarde lejos de niños. ¡Esto no es un juguete!
• Guarde los artefactos que no utilice en el interior. Cuando no los utilice, los artefactos deben guardarse en el interior en un lugar seco, alto
o bajo llave, lejos del alcance de los niños.
• Desconecte los aparatos. Desconecte el aparato de la fuente de energía cuando no lo utiliza.
• El enfriamiento correcto es fundamental al operar el convertidor. No coloque la unidad cerca de los orificios de ventilación del vehículo ni la
exponga a la luz solar directa.
• Uso de suplementos y accesorios. El uso de accesorios o dispositivos no recomendados para este aparato puede resultar peligroso.
• Manténgase alerta. Use el sentido común. No haga funcionar el convertidor cuando está cansado.
• Verifique que no haya piezas dañadas. Cualquier parte se dañe que se debe reparar o substituir correctamente por un centro de servicio
autorizado a menos que se indicare contrariamente a otra parte en este manual de la instrucción antes de que sea futuro utiliza.
• No opere herramientas eléctricas portátiles cerca de líquidos inflamables o en atmósferas gaseosas o explosivas. Los motores de estas
herramientas normalmente chispean, y las chispas pueden encender los vapores.
INSTRUCCIONES DE SEGURIDAD ESPECÍFICAS PARA LOS CONVERTIDORES
ADVERTENCIA: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA:
• No conecte al cableado de distribución de CA.
• No realice conexiones o desconexiones eléctricas en áreas designadas como PROTEGIDAS CONTRA IGNICIÓN. Esta unidad NO está aprobada para
áreas protegidas contra ignición.
• Nunca sumerja la unidad en el agua ni en ningún otro líquido, ni la utilice cuando esté húmeda.
• No inserte los objetos extranjeros en los enchufes del convertidor.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO:
• No opere cerca de materiales, vapores o gases inflamables.
• No lo exponga al calor extremo o a las llamas.
• Si el fusible del enchufe accesorio del vehículo se abre (los soplos) al tapar en este convertidor, no utilice este convertidor con este enchufe
accesorio del vehículo:
No substituya en varias ocasiones el fusible.
No substituya el fusible del enchufe accesorio del vehículo por uno de un grado más alto del amperaje.
Nunca intente remendar el fusible con la hoja o el alambre de lata.
Ninguno de estos acciones pueden causar daño eléctrico serio y/o un fuego.
Este inversor se clasifica para extraer 10 amperios de un enchufe del vehículo 13.8V. Asegúrese de que el sistema de motor en su vehículo pueda
suministrar suficiente energía al convertidor sin hacer al vehículo el fusible accesorio del enchufe abrirse. El fusible debe ser clasificado más arriba
de 12 amperios de la información sobre los grados accesorios del fusible del vehículo se encuentran típicamente en el manual del operador del
vehículo.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE LESIONES O DAÑO A LA PROPIEDAD:
• Desconecte el enchufe de el aparato del enchufe del convertidor antes de trabajar en el aparato.
8
ONE-YEAR LIMITED WARRANTY
Manufacturer warrants this product for one year against any defects in material or workmanship. The defective product will be replaced or
repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a
participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for
exchanges. The second option is to return the product (prepaid) to the manufacturer for repair or replacement at our option. Proof of purchase
may be required.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to
state or province to province.This product is not intended for commercial use.
SPECIFICATIONS
Maximum power: 500 watts continuous
Input voltage: 12.5 volts DC, 48 amps
Output voltage: 110-125 volts AC, 60Hz
Output waveform: Modified Sine Wave
USB: 5VDC, 500mA
DC plug fuse: 10A/250V
Imported by
Baccus Global
399 NW 2nd Avenue, Suite 150
Boca Raton, FL 33432
[phone] RD042809
PC509_ManualENSP_042809.qxp 4/28/2009 11:42 AM Page 8