Star Headlight & Lantern 9900LED User manual

PLIT608 REV. B 12/30/22
MODEL 9901LED MINIBAR
w/Worklight Mounting Option
Please Note: These instructions are provided as a eneral uideline only. Specific
mountin , wirin , and/or weather-sealin may be necessary and are the sole
responsibility of the installer. Star Headli ht & Lantern Co., Inc. assumes no
responsibility for the inte rity of the installation for this or any of its products.
(Worklight not included)
-1-
Mount The Minibar/Workli ht Assembly To The Vehicle
1. Using the gasket as a template, mark the three or four
mounting holes and the center wire hole (if you will be
needing one).
2. Use an 11/6 ” bit to drill out the 3 or holes that you
marked on the vehicle mounting surface.
3. Use a 1/2” drill to drill out the center wire hole (if needed).
. Route your wires through the center hole of the gasket
and mounting surface (if applicable)
5. Attach the Minibar/Worklight assembly using the enclosed
#8-32 X 3/ " 18-8 hex head screws
(for mounting surfaces 3/16”-3/8”
thick), flat washers, and tooth
washers as shown to the left.
Insert the bolts from below, fastening them into the same
threaded inserts used to attach the worklight inside the
minibar. Tighten until snug.
(Note: Use longer bolts if your mounting surface is thicker than 3/8”)
The model you received has been designed to be compatible with a Go Light™ GT, Radio
Ray, Stryker, Stryker Hardwire, Stryker ST Series (or most other worklights with identical
mounting patterns). For proper installation, first mount the worklight to the minibar, then
mount the minibar/worklight assembly to the vehicle.
Mount The Workli ht To The Minibar
1. Use an 11/6 ” bit to carefully drill out the 3 or
holes in the dome that correspond with the
mounting pattern of your worklight. Ensure that your
bit is perpendicular to the surface of the dome.
2. Use an 1/2” drill to drill out the center post hole of
the dome to allow for wire access.
3. Following the
manufacturer’s instructions
for the worklight, remove
the base from the worklight.
. Place the worklight base on the top of the minibar dome and
align the corresponding holes.
5. Use the #8-32 X 1-1/ " 18-8 pan head mounting screws
and washers provided with the
minibar to attach the worklight
base to the minibar ( -screw
version shown).
6. Route the wire harness from the worklight through the center
hole in the worklight base and the minibar dome and follow the
manufacturer’s instructions included with your worklight to
reassemble it to the base.
ounting Instructions
(when used with optional Worklight)
IMPORTANT: Please read all of the following instructions before installing your new light.
4-Hole Layout
3-Hole Layout

-2-
Hard Wire Instructions (Perm ount odels)
CAUTION: All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load. Testin the li ht before this fuse is properly installed will
void the warranty on the li ht.
Connect the worklight wires as follows:
BLACK - (Ground) Connect to the negative side of the battery.
RED - (Power) Connect to +12 VDC through your switch. Be sure to use a 10 amp fuse
when connecting the switch to the positive side of the power supply.
PURPLE - (Optional - High/Low) Switches the light between High and Low power.
• High Power Only: Leave disconnected (cover wire with wire nut or tape).
• Low Power Only: Connect to +12VDC or Ground.
• High/Low witching Option: Connect to 12VDC or Ground through a switch.
GREEN - Touch and release to +12VDC or GROUND to scroll through patterns.
WHITE - ( ynchronization) To synchronize the flashing of multiple units, connect the white
wires from up to six units together, ONLY AFTER PROGRA ING them for the
same pattern (see ynchronization of Multiple Lights section on next page).
If you are only installing one unit, cut the White wire short and tape the end.
• To change patterns briefly touch and release the Green wire to +12VDC.
• The cycle repeats after the last pattern.
• Pattern Shortcuts: Hold the Green wire to +12VDC for the length of time that corresponds to
the pattern you would like to jump to.
After selecting a pattern, deactivate the light to store the selected pattern.
Pattern Programming
Refer to the instructions enclosed with your worklight for proper connection of those wires.
† SAE J8 5 Compliant Patterns when properly configured
-3-
Synchronization of ultiple Lights
You can synchronize up to six lights with compatibility.
DO NOT CONNECT WHITE WIRES UNTIL PROGRA ING HAS BEEN CO PLETED
FOR ALL LIGHTS!!
1. Power up the first unit and select a Phase 1 pattern.
2. Program the second light with the same Pattern Type.
• Use the same Phase if you want the lights to flash together (simultaneous).
• Use the opposite Phase if you want the lights flash opposite one another (alternate).
3. After programming all lights, tie off the Pattern Select wires and connect the white wires
together.
. Test lights by applying power to all of them at the same time.
NOTICE
Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice. Star Headlight Lantern Co., Inc. makes no warranty of any
kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness
for a particular purpose. Star Headlight Lantern Co., Inc. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use of this manual.
If you have any questions concerning this or any other product,
please contact our Customer Service Department at [phone].
If a product must be returned for any reason, please contact our Customer Service Department to
obtain a Returned Material Authorization number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and workmanship for five years
after the date of purchase. The owner will e responsi le for returning to the Service Center any defective
item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its
option, products, or part(s), which its inspection determines to e defective. Repaired or replacement
item(s) will e returned to the purchaser with transportation costs prepaid from the service point. A copy of
the purchaser's receipt must e returned with the defective item(s) in order to qualify for the warranty
coverage. Exclusions from this warranty include, ut are not limited to, domes, and/or the finish. This
warranty shall not apply to any light, which has een altered, such that in the manufacturer's judgment, the
performance or relia ility has een affected, or if any damage has resulted from a normal use or service.
There are no warranties expressed or implied (including any warranty of merchanta ility or fitness), which
extend this warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or
consequential damages, including costs of any labor, are not covered. The manufacturer reserves the right
to change the design of the product without assuming any o ligation to modify any product previously
manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from state to
state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow
the exclusion or limitation of incidental or consequential damages. Therefore, the a ove limitation(s) or
exclusion(s) may not apply to you.