Star Headlight & Lantern Contour S-Link System 9100DLED DUAL-COLOR... User manual

PLIT596 REV. - 10/1/19
MODEL 9100DLED DUAL-COLOR MINIBAR
featuring the

-1-
Please Note: These instructions are provi e as a general gui eline only. Specific
mounting, wiring, an /or weather-sealing may be necessary an are the sole
responsibility of the installer. Star Hea light & Lantern Co., Inc. assumes no
responsibility for the integrity of the installation for this or any of its pro ucts.

-2-
1. IMPORTANT: Please read all of the following instructions before installing your new
warning light.
2. CAUTION: All of our DC powered warning lights are polarity sensitive. These lights are
polarity protected only if the appropriate fuse is used. All wires connected to the positive
terminal of the battery should be fused at the battery for their rated load. Testing the
light before this fuse is properly installe will voi the warranty on the light.
3. Permanent mount lights are mounted using four bolts that screw into molly well nuts in
each corner of the minibar. ark the four mounting holes (and the center wire hole, if
you will be needing one). ark the holes on the corners of a 14-1/2” x 5-1/2” rectangle.
4. Check the underside of the marked locations to ensure that you do not damage any
wires or other components. Drill a 3/16”" hole in the four marked spots for the mounting
bolts, and one in the center for your wires (if applicable).
CAUTION: Take care not to rill through the hea liner below.
5. If the 4 threaded molly well nuts are not already installed in
the base of your bar, install them by pressing one into each
of the four holes found on the corners of the base of the
light until the lip rests on the bottom surface of the base.
6. Route your wires through the center hole (if applicable) and attach the light using the
four enclosed bolts. Insert the bolts from below, through the holes you drilled in the
mounting surface and screw them into the molly well nuts on the light. Tighten until
snug.
Mounting Instructions

-3-
White - (Synchronization) Used to synchronize two lights together. If you are
only installing one unit, cut the White wire short and tape the end. If you
will be synchronizing two or more approved synchronizable lights, leave
the white wire disconnected for now. Connect the white wires from both
units together ONLY AFTER PROGRAMMING them for the same
pattern (see Pattern Programming).
Red - (Power Color 2) Connect to +12 VDC through your switch. Be sure to
use a 0 amp fuse when connecting the switch to the positive side of
the power supply.
Orange - (Power Color 1) Connect to +12 VDC through your switch. Be sure to
use a 0 amp fuse when connecting the switch to the positive side of
the power supply.
Purple - (Optional High/Low) Used to switch the light between High and Low
power.
 Leave disconnected for High Power only (cover with wirenut or
tape).
 Connect to +12VDC for Low Power only.
 Connect to +12VDC through a switch for High/Low switching option.
Red w/Green - (Pattern Select) Touch and release to +12 VDC to change patterns.
Black - (Ground) Connect to the negative side of the battery.
Electrical Connections
WHITE: Synchronization (Optional) - AFTER setting flash patterns
connect white wires from synchronized lights together.
Cut short and cap off if not synchronizing.
RED: Power (Color 2)
ORANGE: Power (Color 1)
PURPLE: High/Low Power Select +12VDC for Low / Open for High
RED w/GREEN: Pattern Select Touch and release to +12VDC
BLACK: Good Chassis Ground
10A
FUSE

-4-
PATTERN PROGRAMMING
The Orange and Red wires can
each be programmed for its own
pattern.
1. Activate the wire that you
wish to program (Orange or
Red) by connecting it to
power (and the Black to
Ground).
2. Touch and release the
Pattern Select wire (Red w/
Green) to +12 VDC to scroll
through the patterns listed to
the right. The cycle repeats
after the last pattern.
Use the programming
shortcuts listed in the chart
below and to the right to
quickly jump to several
different patterns by holding
the Red w/Green Stripe Wire
to +12 VDC for the
corresponding length of time
for the pattern you would like
to jump to.
3. Once you find the pattern you
wish to display, tape off the
Red w/Green wire, and
deactivate the light. This will
store the selected pattern.
Hold Patt. Sel.
to +12VDC For Unit Blinks Shortcut to
3 seconds 1 time Pattern 1
6 seconds 2 times Pattern 6
9 seconds 3 times Pattern 13
12 seconds 4 times Pattern 28
15 seconds 5 times Steady Burn
18 seconds 6 times
Toggles Dual
Color Mode
Programming
DUAL-COLOR MODE
The default setting is for the Orange and Red wires to each activate a different color. If
desired, you can program one wire to activate both colors. To do so, proceed as follows:
1. Activate the wire that is desired to be changed (Red or Orange) by connecting it to
+12VDC and connecting the Black wire to Ground.
2. Hold the Pattern Select wire (Red w/Green stripe) to +12VDC until the light flashes 6
times (~18 seconds), then release the wire. The activated wire should now be
displaying both colors.
3. Repeat process to turn off dual color mode.
STEADY BURN MODE
To program either of the wires for
Steady Burn ode, activate that wire
and hold the Pattern Select wire (Red
w/Green) to power until the light
blinks 5 times (~15 seconds).

-5-
Hold Patt. Sel. and Synch
Wires to +12VDC for Unit Blinks Priority ode Shortcut
3 seconds 1 time o Priority
6 seconds 2 times Orange Priority
9 seconds 3 times Red Priority
12 seconds 4 times Toggles Sequential Mode
To change the Priority ode, Proceed as follows:
1. Connect either the Red wire or the Orange wire to +12VDC and connect the black wire
to ground.
2. Hold both the Pattern Select wire (Red w/Green stripe) and the Synch wire (White) to
+12VDC, releasing them after the light flashes the corresponding number of times
indicated in the chart below.
NOTICE
Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice. Star eadlight & Lantern Co., Inc. makes no warranty of
any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Star eadlight & Lantern Co., Inc. shall not be liable for errors contained herein
or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual.
(Programming CONT’D)
PRIORITY MODES
If both colors are activated (either by using both wires, or if you have set one wire for Dual-
Color ode), the default setting is for both colors to flash their pattern, one after the other
(No Priority in Sequential ode). There are 3 optional Priority settings:
 Orange Priority: If both wires are activated only the Orange wire functions.
 Red Wire Priority: If both wires are activated only the Red wire functions.
 Sequential/Integrated Mode:
► Sequential ode: (Default setting) If both colors are activated the light
will run a full cycle (On then Off) of one of the colors and its
corresponding pattern, then run a full cycle of the other color
and its corresponding pattern.
► Integrated ode: If both wires are activated the light will flash both colors
using the pattern of the Orange wire. For alternating
patterns, the colors will alternate halves back and forth with
one color flashing on one side of the light and the other color
flashing on the other side of the light at the same time. For
simultaneous patterns, the entire light will quickly flash the
pattern in one color, then the other color (similar to
Sequential mode, but no off time).

-6-
If you have any questions concerning this or any other product, please contact our
Customer Service Department at [phone].
If a product must be returned for any reason, please contact our
Customer Service Department to obtain a Returned aterials Authorization
number (R A #) before you ship the product back.
Please write the R A # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and workmanship for five
years after the date of purchase. The owner will be responsible for returning to the Service Center any
defective item(s with the transportation costs prepaid. The manufacturer will, without charge, repair
or replace at its option, products, or part(s , which its inspection determines to be defective. Repaired
or replacement item(s will be returned to the purchaser with transportation costs prepaid from the
service point. A copy of the purchaser's receipt must be returned with the defective item(s in order to
qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, domes,
and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the
manufacturer's judgment, the performance or reliability has been affected, or if any damage has
resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness ,
which extend this warranty period. The loss of use of the product, loss of time, inconvenience,
commercial loss or consequential damages, including costs of any labor, are not covered. The
manufacturer reserves the right to change the design of the product without assuming any obligation
to modify any product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from
state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above
limitation(s or exclusion(s may not apply to you.

-7-