Star Headlight & Lantern ULB34 User manual

ULB34
Rear Window Phantom
PLIT533 REV. - 9/15/15

-1-
Mounting Instructions
1. The typical mounting area for this light is along the top moulding inside the rear hatch.
2. Alternately the light can be mounted to the trim above the window, on the rear hatch
itself.

-2-
It is the sole responsibility of the owner to ensure the lightbar is
mounted securely. Check your light every time you enter the
vehicle to ensure that it is mounted securely. The manufacturer
assumes no responsibility for the secure mounting of this light.
Please Note: These instructions are provided as a general guideline only. Some
vehicles may require special mounting, wiring, and/or weather sealing. This is the
sole responsibility of the installer. Star Headlight & antern Co., Inc. assumes no
responsibility for the integrity of the installation for this or any of its products.
(Mounting CONT’D)
3. Hold the light up to the location where it is to be mounted. We recommend aligning
the corner of the bend in the bracket with the rear edge of the moulding above the rear
window.
4. Using the brackets as a template, mark your mounting holes.
5. Carefully drill appropriately sized pilot holes in the marked locations, based upon the
size of your mounting hardware (user supplied).
6. Install the light making any necessary adjustments to the brackets prior to tightening all
of your screws. Ensure that the unit is level to the ground so that the light shines
unobstructed through the rear window. Check the angle of the light by standing 20
feet behind the vehicle. Adjust the light up, down, right, or left to obtain the brightest
output directly to the rear of the vehicle.
7. Carefully tighten all the screws once the light has been adjusted satisfactorily.
2. Attach the mounting brackets to the back
of the light. eave the screws loose to
allow for bracket adjustment.

-3-
The U B34 is powered through the 4-wire harness that comes pre installed on the light. Connect
the four wires as follows:
Black - (Ground) Connect to a good chassis ground
Red - (Power/+12 VDC) Connect to your On/Off switch (not supplied) through a 5 amp
fuse (not supplied).
Green - (Pattern Select) Touch to a ground to change patterns
(see Pattern Programming section on next page)
White - (High/Low) Controls the intensity of the light
ow Only: Connect the white wire to a good chassis ground if you wish to
run the light on low power.
High Only: Tape the end of the white wire off so that it does not come into
contact with ground, if you wish to operate the light on high
power.
Switched: Connect the white wire through a switch to ground if you would
like to have the ability to switch between high and low power.
All standard Phantom lights are designed for 12VDC negative ground vehicles only.
Reverse polarity may cause serious damage to the lightbar and/or vehicle. Contact
the automotive dealer if there are any doubts about the polarity of your vehicle.
Wiring Instructions
GOOD
CHASSIS
GROUND
Ground = ow
Open = High
WHITE
5 AMP
FUSE
Touch and release to
ground to change patterns
B ACK
GREEN
RED
HIGH/ OW
SWITCH
(Optional)
CONNECT
TO +12 VDC
4-Conductor Cable
From U B34

-4-
Pattern List
1. Slow Warn
2. Fast Warn
3. Superfast Warn
4. Warn Fade*
5. Pre-Pop Warn
6. All Singleflash
7. Alt. Tripleflash
8. All Tripleflash
9. Alt. Quadflash w/Post Pop
10. All Quadflash w/Post Pop
11. Alt. Quintflash
12. All Quintflash
13. Alt. Pre-Pop Quintflash
14. All Flicker
15. Alt. PSU Flicker
16. One Side Pop, Other Rapid Fire
17. One Side Rapid Fire, Other Pop
18. Comet 1*
19. Comet 2*
20. Delta Omega (Flash Rate Sweep)
21. Slow Warn, Alt. Tripleflash
22. Slow Warn, Super Fast Warn
23. All Doubleflash, Alt. Doubleflash
24. All Doubleflash, Alt. Doubleflash, Flicker
25. Alt. Doubleflash, Flicker
26. All Double, Alt. Pre-Pop Tripleflash, Slow Warn
27. Alt. Doubleflash Non-Synch
28. Alt. Tripleflash, Alt. Pre-Pop-Triple, Flicker †
29. Alt. Quadflash, Flicker, Alt. Doubleflash, Flicker
30. Alt. Pre-Pop Quintflash, Alt. Quintflash, Flicker
31. One Side Steady-----One Side Singleflash
32. One Side Steady-----Other Side Short- ong
33. Medium Warn (Alternating ong Singleflash)
34. Alternating Short - Alternating ong
35. Demo Mode – oop All Patterns
† Default Pattern
* These patterns do not dim under low power
P EASE NOTE : The green wire is only used for programming purposes during installation.
1. Connect the black wire to Ground.
2. Activate the light by applying power (+12VDC) to the red wire.
3. Briefly touch and release the green wire to ground to scroll through the patterns listed
below. The cycle will repeat itself after the last pattern.
4. Once you find the pattern you wish to select, leave the green wire disconnected and
turn the unit off. This will program that pattern into the memory. Tape the end of the
green wire so that it does not come into contact with ground accidentally.
NOTE: If at any time you would like to reset the pattern to the factory default, simply touch
the green wire to ground for six seconds until the light blinks twice.
Pattern Programming

-5-
N TICE
Due to continuous product improvements, we must reserve the right to change any specifications and information, contained in
this manual at any time without notice. tar Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this
manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. tar
Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this manual.
If you have any questions concerning this or any other product, please contact our
Customer Service Department at [phone].
If a product must be returned for any reason, please contact our
Repair Department at [phone] or [email protected]m to obtain a
Returned Materials Authorization number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and workmanship for five
years after the date of purchase. The owner will be responsible for returning to the Service Center any
defective item(s with the transportation costs prepaid. The manufacturer will, without charge, repair
or replace at its option, products, or part(s , which its inspection determines to be defective. Repaired
or replacement item(s will be returned to the purchaser with transportation costs prepaid from the
service point. A copy of the purchaser's receipt must be returned with the defective item(s in order to
qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, domes,
and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the
manufacturer's judgment, the performance or reliability has been affected, or if any damage has
resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness ,
which extend this warranty period. The loss of use of the product, loss of time, inconvenience,
commercial loss or consequential damages, including costs of any labor, are not covered. The
manufacturer reserves the right to change the design of the product without assuming any obligation
to modify any product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from
state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above
limitation(s or exclusion(s may not apply to you.
These lights use state-of-the-art ight Emitting Diode ( ED) technology. This light is
comprised of ultra-bright EDs that are operated in a multiplexed mode to efficiently
produce light output with lifetimes up to 100,000 hours. Under normal circumstances, you
will not need to replace any EDs in this light. If any of the ED's in your light do fail,
please contact Star Headlight for arrangements to have them repaired.