StarTech.com PCIe 40G QSFP+ User manual

PCIe 40G QSFP+ Network Card
User Manual
Ver. 1.00
All brand names and trademarks are properties of their
respective owners.

Page 2
Contents:
Chapter 1: Introduction......................................................3
1.1 Product Introduction....................................................3
1.2 Features........................................................................3
1.3 Requirements...............................................................4
1.4 Package Contents.........................................................4
Chapter 2: Getting Started .................................................5
2.1 Hardware Layout.........................................................5
2.2 Hardware Installation ..................................................7
2.3 Driver Installation........................................................7
2.3.1 Installation for Windows.......................................7
2.3.2 Installation for Linux............................................9
2.4 Verifying the installation............................................10
2.4.1 Verifying for Windows........................................10
2.4.2 Verifying for Linux.............................................11

Page 3
Chapter 1: Introduction
1.1 Product Introduction
Get fast, high-bandwidth connectivity with this dual-port QSFP+
Network Interface Card. It connect QSFP+ slots to your server or
workstation. The 40G NIC features an Intel® controller and provides
redundant network links with reliable performance.
1.2 Features
Supports common 40GbE SFPEnergy Efficient Ethernet (EEE)
Up to 9K Jumbo Frames
IP, TCP and UPD checksum offloading (IPv4, IPv6) capabilities
Designed to meet PCI Express Specification Revision 3.0
Eight lane (x8) PCI Express compatible with x8 (or higher) slots
IEEE 802.1Q Tagged VLAN
IEEE 802.3ba 40GBASE-SR4
IEEE 802.3ba 40GBASE-LR4
Intel PROSet Utility for Microsoft Device Manager

Page 4
1.3 Requirements
Hardware
The following system specs are recommended minimum
PCIe slot: Available 4-Lanes PCI-Express slot gen 2.0 or later
Processor: Quad Core 3.0GHz or higher
RAM: 4GB memory or higher
Software
Operating systems supported are (64 bits Only)
Windows Server 2008 R2
Windows Server 2012
Windows Server 2016
Linux 2.6.24 to4.11.x or later
1.4 Package Contents
1 x PCIe 40G QSFP+ Network Card
1 x Driver CD
1 x User Manual

Page 5
Chapter 2: Getting Started
2.1 Hardware Layout
1-Port

Page 6
2-Port
Link/Activity Indicator:
When the LED is off, there is no link between the PCIe 40G
QSFP+ Network Card and the network
When the LED is on, a link is established, but there is no traffic
on the network
When the LED is flashing, there is traffic on the network to
which the PCIe 40G QSFP+ Network Card is connected

Page 7
2.2 Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCIe slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Secure the computer cover and reconnect the power cord.
2.3 Driver Installation
The following section shows you how to install PCIe 40G QSFP+
Network Card driver on different operating systems.
2.3.1 Installation for Windows
 Insert the provided CD into your disk drive. The CD-ROM
will start automatically. The following screen will show up and
please click “Install Driver”.

Page 8
*Note: Actual image may vary
Note: If the install program doesn’t run automatically, please
locate and double-click on the Autorun.exe file in the CD to
launch the install program.
 Please click “PCIe Intel” to start the installation.
 Follow the instructions on screen to install the driver.

Page 9
2.3.2 Installation for Linux
1. Insert the provided CD into your CD-ROM drive.
2. Extract the compressed driver source file to a certain directory by
the following command: (Please copy the driver file “i40evf-x.x.x.
gz” from the CD folder “.Driver\Intel\PRO40GB\Linux” to a
certain folder on hard drive)
# i40evf-x.x.x.gz
3. Now, the driver source files should be extracted under the current
directory. Executing the following command to compile the
driver:
# make
4. If the compilation is well, the i40evf-x.x.x.ko will be created
under the current directory.
5. If you want to use modprobe command to mount the driver,
executing the following command to install the driver into your

Page 10
kernel:
# make install
2.4 Verifying the installation
2.4.1 Verifying for Windows
1. Click on the “Device Manager” tab in the Windows Control
Panel.
Start > Control Panel > Device Manager
2. Entry “Network adapters” item, and you can read “Networks
40GbE Adapter” in the Device Manager.