StarTech.com ST100S User manual

Network Adapter
ST100S
ST100SLP (Low Profile)
Instruction Manual
Actual product may vary from photo
10/100 Mbits/sec PCI Ethernet Network Card

FCC
Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aannddootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss
This manual may make reference to trademarks, registered trademarks, and other protected names
and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur
these references are for illustrative purposes only and do not represent an endorsement of a
product or service by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct acknowledgement
elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing the Network Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Connecting Your Card to a Network . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Verifying Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Monitoring your Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Tips for Setting Up your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Instruction Manual
i
Table
of Contents

Instruction Manual
1
Thank you for purchasing a StarTech.com 10/100 Mbits/sec PCI Ethernet card. Featuring
Auto-Negotiation capability and support for data transmission bandwidth from 10Mbps to
100Mbps, the card is easy to install and set up, and is fully Plug and Play compatible in a
wide range of operating environments.
Introduction
•Support for IEEE802.3x Full-Duplex flow control
Features
System requirements:
•An IBM-compatible computer with a Pentium-based processor
Package contents:
•1 x PCI Ethernet Adapter card
This package should contain:
•Capable of full and half-duplex communications
•Complies with industry standards: IEEE 802.3, 100BaseTX and 10BaseT standard
•Supports 32-bit PCI Bus Master for high performance and low processor utilization
•One of the following operating environments: Windows Vista/XP/ME/2000/98/95,
Windows NT, Linux, NetWare 3.x/4.x, Lan Manager, TCP/IP software
•An available PCI slot
•1 x Driver disk
•1 x Installation Guide
•1 x Full-size Bracket (ST100SLP only)

Instruction Manual
2
Installation
Installing the Network Card
WARNING! PCI cards, like all computer equipment, can be severely
damaged by static electricity. Be sure that you are properly grounded before
opening your computer case or touching your PCI card. StarTech.com
recommends that you wear an anti-static strap when installing any computer
component. If an anti-static strap is unavailable, discharge yourself of any
static electricity build-up by touching a large grounded metal surface (such
as the computer case) for several seconds. Also be careful to handle the PCI
card by its edges and not the gold connectors.
1. Shut down all power connected to the computer, as well as all devices connected to
the computer peripherally (i.e. Printers, Monitors, Scanners etc.). As an added step to
ensure safe installation, unplug the power supply from the computer.
2. Remove the computer cover. For more detailed instruction on how to perform this
step, please refer to the documentation that was included with your computer at the
time of purchase.
3. Locate an empty PCI slot, removing the metal bracket covering the accompanying
empty port/socket.
4. Position the serial card above the open PCI slot, ensuring that the card is aligned with
the entire slot. Insert the card firmly into the slot, distributing force evenly across the
length of the board. Once inserted, secure the card into the adjoining socket
(previously covered by metal bracket), using the correct size screw (please consult
documentation that accompanied purchase of computer).
5. Replace the computer cover and re-connect all power to the computer.
Connecting Your Card to a Network
Depending on how you are planning on using the card, the device you are connecting it
to and the type of cable you need may differ. To take advantage of the NIC’s 100
Mbits/sec capacity, it is recommended that you always use at least Category 5 Ethernet
cable. If you are unsure of the type of cable required for your device, consult your device
manufacturer.
NOTE: StarTech.com carries a wide range of Ethernet cables in various colors and
lengths. For more information on these products, as well as tips and ideas for
setting up and running your network, visit http://www.startech.com and click on
the Networking tab near the top of the screen.
• If you are connecting your computer directly to another computer, you need to
use a crossover cable.
• If you are connecting your computer to a hub or switch, you should use a
straight-through cable.

Instruction Manual
3
• If you are connecting your computer to the Internet via a DSL or cable modem,
you should use the cable recommended by the modem manufacturer.
Verifying Driver Installation
To verify that the drivers have successfully been installed, right-click on My Computer,
and select Manage. In the left-most column of the next screen (
Computer
Management ), click on Device Manager. In the right-most column, click on the [+]
symbol located next to Network Adapters, which will expand the Network Adapters
listing, detailing the devices that are installed.
Monitoring Your Card
The LED on the front of the card is the best indication of the card’s activity. If the
Link/Activity LED is not lit, there is a connection error. Please ensure that all devices are
turned on and that the network cable is properly connected at both ends. Also make sure
that your network cables comply with EIA/TIA 568 and Category 5 specifications.
If problems persist, power down all devices and disconnect all plugs. Wait at least ten
seconds then plug the devices back in and power them up.
Tips for Setting Up Your Network
For information and help on setting up your network, please consult the manufacturer of
your operating system. The following is section details troubleshooting steps only and is
intended for Microsoft users on a local area network.
Make sure your computers are configured properly
For your convenience, you should configure each of your computers so that they can
“see” each other and share devices and files. To do this, you have to make sure that the
Installing the Drivers
NOTE: Windows Vista/XP/2000 will automatically detect the new hardware and install the
necessary drivers without any user input.
The following are installation instructions for Windows OS only. If you are using Linux,
Netware, or any other supported environment, consult the driver installation instructions
available in the most recent driver download folder, available by locating
ST100S/ST100SLP on our website, http://www.startech.com, and clicking Downloads.
Windows 95/95/ME
1. Windows will automatically detect the new hardware. Click Next.
2. Choose Driver from disk provided by hardware manufacturer, and direct
Windows to the folder where the most recent drivers have been saved.
3. Follow any additional on-screen prompts and reboot your computer to complete the
installation process.

following have been installed on your computers:
• Client for Microsoft Networks
• TCP/IP (Internet Protocol)
• File and Print Sharing
These clients, protocols, and services can be found in the following locations:
Windows Vista
1. From the Control Panel, click on Network and Sharing Center.
2. Click Manage Network Connections.
3. Right-click on Local Area Connection and choose Properties.
Windows XP
1. Click on Start, then click My Network Places.
2. Click View Network Connections in the Network Tasks box.
3. Right-click on Local Area Connection and choose Properties.
Windows 2000
1. Click on Start, then Settings, then Network and Dialup Connections.
2. Double-click Local Area Connections and click the Properties button.
Windows Me/98/95
1. Click on Start, then Settings, then Control Panel.
2. Double-click on Network.
NOTE: If you need to add any of the following components, check your Windows
documentation for details.
Make sure all your computers are on the same workgroup
To be able to communicate properly with each other, each computer must be located on
the same workgroup. Each computer within a workgroup must have a unique name. To
ensure compatiblility between each version of Windows, keep your computer names
under 13 characters long.To view, add, or edit your computer’s name, do the following:
Windows XP
1. Click Start and then Control Panel.
2. Double-click System then click on the computer name tab.
Windows 2000
1. Click on Start, then Settings, then Control Panel.
2. Double-click on System.
3. Click on the Network Identification tab.
Windows ME/98/95
1. Click Start, then Settings, then Control Panel.
2. Double-click Network, then click the Identification tab.
Instruction Manual
4

Make Sure Your Sharing is Set Up Properly
1. Go to your network dialog box using the procedure explained under “Make sure
your computers are configured properly“ (page 3).
2. Click on File and Print Sharing.
3. Choose whether you want to install one, both, or neither of these options. Click OK.
4. Decide what files or folders you want to share.You can call up sharing options by
right-clicking on a file or folder and choose Sharing (Windows 2000/Me/98/95) or
Sharing and Security (Windows XP).
NOTE: If you are having any difficulties setting up or using your network, please contact
your operating system vendor.
Instruction Manual
5

Instruction Manual
6
Technical
Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
Warranty
Information
This product is backed by a lifetime warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted, following
the initial date of purchase. During this period, the products may be returned for repair, or
replacement with equivalent products at our discretion. The warranty covers parts and
labor costs only. StarTech.com does not warrant its products from defects or damages
arising from misuse, abuse, alteration, or normal wear and tear.
Limitation
of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Specifications
Bus Type PCI
Form Factor Standard Profile
Connectors 1 x RJ45 Port
Maximum Data Transfer Rate 100Mbps
Chipset Realtek RTL8100C
Regulatory certifications FCC, CE, ROHS

24 August 2007 (Rev. A)
About
StarTech.com
StarTech.com is “The Professionals’ Source for Hard-to-Find Computer Parts”.
Since 1985, we have been providing IT professionals with the quality products
they need to complete their solutions. We offer an unmatched selection of
computer parts, cables, server management solutions and A/V products and
serve a worldwide market through our locations in the United States, Canada, the
United Kingdom and Taiwan.
Visit www.startech.com for complete information about all our products and to
access exclusive interactive tools such as the Parts Finder and the KVM
Reference Guide. StarTech.com makes it easy to complete almost any IT
solution. Find out for yourself why our products lead the industry in performance,
support, and value.