StarTech.com PEX1000SFP User manual

Manual Revision: 08/14/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
PEX1000SFP
PCI Express Gigabit Ethernet Fiber
Open SFP Network Card
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction ............................................................................................1
Features ........................................................................................................................................................ 1
Package Contents ..................................................................................................................................... 1
Installation ..............................................................................................2
Hardware Installation .............................................................................................................................. 2
Connecting to a Network ....................................................................................................................... 3
Software Installation ................................................................................................................................ 4
Specications ..........................................................................................5
Technical Support ..................................................................................6
Warranty Information ............................................................................6

Instruction Manual
1
Introduction
The PEX1000SFP PCI Express Gigabit Ethernet Fiber Open SFP Network Card lets you
connect a PCI Express-based PC directly to a ber optic network using the Gigabit SFP
of your choice.
A versatile solution for connecting a computer directly to a gigabit ber network,
the PCIe SFP network adapter enables you to choose the Gigabit SFP that best suits
your network ber connection and distance requirements (see our full line of Gigabit
transceivers for compatible solutions).
Ideal for secure network setups, the open SFP NIC oers a direct ber connection
which is not susceptible to electronic interference like standard RJ45 networks.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Features
• Supports Full/Half-duplex Auto-Negotiation, Auto-MDI/MDIX
• Compliant with IEEE 802.3z 1000Base-SX/LX, IEEE802.1Q VLAN Tagging, IEEE802.1p
Layer 2 Priority Encoding, IEEE 802.3x full duplex ow control, RFC 1157 SNMP v1
• Jumbo Frame Support
• Supports PCI Message Signaled Interrupt (MSI)
• Preboot Execution Environment (PXE) 2.1
Package Contents
• 1 x PCI Express Open SFP Network Card
• 1 x Driver CD
• 1 x Instruction Manual

Instruction Manual
2
Installation
WARNING! PCI Express cards, like all computer equipment, can be severely damaged
by static electricity. Be sure that you are properly grounded before opening your
computer case or touching your PCI Express card. StarTech.com recommends that you
wear an anti-static strap when installing any computer component. If an anti-static
strap is unavailable, discharge yourself of any static electricity build-up by touching a
large grounded metal surface (such as the computer case) for several seconds. Also be
careful to handle the PCI Express card by its edges and not the gold connectors.
Hardware Installation
1. Turn OFF the computer power before installation.
2. Remove the chassis cover from your computer.
3. Locate an unused PCI Express slot and remove the corresponding slot cover from
the rear panel of the computer chassis. Retain the screw (if applicable) used to hold
the slot cover in place.
4. Align the PCI Express card with the unused PCI Express expansion slot. Applying
pressure evenly across the top edge of the expansion card, rmly but gently insert the
card into the slot, ensuring that the card is properly aligned with the rear panel slot.
5. Secure the card to the motherboard and rear chassis using the screw removed in
step 3 (if necessary). Secure the additional serial port provided by the daughter
board (smaller circuit board to an adjacent rear bracket.
6. Replace the chassis cover (removed in step 2).
7. Power on the computer. Once the computer has been rebooted, the operating
system will detect that the PCI Express card has been installed and request driver
installation, detailed in the next section.

Instruction Manual
3
Connecting to a Network
Note: You must connect the PCI Express Fiber Gigabit Ethernet Adapter to the network
before installing the network driver.
For connector type, cabling requirements, and maximum segment distance when
connecting the PCI Express Gigabit Ethernet Adapter to your network, please refer to
the following table.
Speed Connector
Port Speed
Half/Full
Duplex
Cable Max.
Distance
1000Base-T RJ-45 2000 Mbps 4-pair UTP/
STP Cat.5 100m
1000Base-SX SC, LC 2000 Mbps MMF (62.5μm) 220m
2km
1000Base-SX SC, LC 2000 Mbps MMF (50μm) 550m
1000Base-LX SC, LC 2000 Mbps SMF (9, 10μm) 10, 20, 50km
1000Base-BX SC, LC 2000 Mbps SMF (9, 10μm) 20, 40km
1. Install your desired SFP into the SFP slot on the card.
2. Prepare a network cable with corresponding connectors for the two end devices,
one end to the PCI Express Fiber Gigabit Ethernet Adapter and the other to a
1000Mbps ber port on the network switch.
3. Connect the network cable to the connector on the PCI Express Fiber Gigabit
Ethernet Adapter. This network cable consists of two individual cables: one for
‘transmission (TX)’, and the other for ‘reception (RX)’.
4. Connect the other end of the network cable to a 1000BASE-SX switch.
5. i. Insert the cable that is connected to the transmit (TX) connector on the PCI
Express Fiber Gigabit Ethernet Adapter into the receive(RX) connector on the
network switch.
ii. Insert the cable that is connected to the receive (RX) connector on the PCI
Express Fiber Gigabit Ethernet Adapter into the transmit (TX) connector on the
network switch.
6. When the cable is properly connected to two end devices, turn on the power to
the PC.
7. Check the LNK (Link) LED. The LED will come on when the PCI Express Fiber Gigabit
Ethernet Adapter is receiving a good link signal from the connected device, a switch.

Instruction Manual
4
Software Installation
1. Once PEX1000SFP has been installed in the computer, turn on the power to
the computer.
2. When the Found New Hardware Wizard
window pops up, select Install from a list
or specic location (Advanced)and click
Next to continue.
3. Select Search for the best driver in these
locations. and then select Include this location
in the search. Click Browse to specify the driver
location and click Next to continue.
4. Installation will begin...
5. Click Finish to complete the driver installation.

Instruction Manual
5
Specications
Applicable Standards
IEEE 802.3z 1000Base-SX/LX
IEEE802.1Q VLAN Tagging
IEEE802.1p Layer 2 Priority Encoding
IEEE 802.3x full duplex ow control
RFC 1157 SNMP v1
LED Indicators Link, Activity
Operating Temperature 0°C ~ 45° C (32°F ~ 113°F)
Storage Temperature -10°C ~ 70°C (14°F ~ 158°F)
Humidity 5% ~ 95% RH non-condensing
Chipset Realtek - RTL8168B
Marvell - 88E1111-RCJ1
Maximum Connection Distance Dependent on the SFP used
OS Support
Windows® 8 (32/64bit), 7 (32/64),
Vista(32/64), XP(32/64), 2000 Windows®
Server 2008 R2, 2003(32/64)
Linux 2.4.x/ 2.6.x

Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.