StarTech.com ARMDUAL2 User manual

Manual Revision: 09/23/2019
User Manual
For the latest information and specications visit
www.startech.com/AMRDUAL2
Desk Mount Dual Monitor Arm | Crossbar
Design | Articulating
Actual product may vary from photos
SKU#: ARMDUAL2

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
• Make sure that you assemble this product according to the instructions.
• Do not exceed the weight capacity of this product. Overloading this product
might result in injury or property damage. This product can support the
following weight: 35.2 lb. (2 x 8 kg).
• This product is intended for indoor use only and should not be used
outdoors.
Varningsmeddelanden
• Se till att du monterar produkten i enlighet med instruktionerna.
• Överskrid inte produktens viktkapacitet. Överbelastning av produkten kan
orsaka skada på person eller egendom. Denna produkt har stöd för följande
vikter: 2 x 8 kg.
• Produkten är endast avsedd för användning inomhus och ska inte användas
utomhus.
Avertissements
• Assemblez ce produit conformément aux instructions.
• Ne dépassez pas la capacité pondérale du produit. Une surcharge du produit
peut entraîner des blessures ou des dommages matériels. Ce produit peut
supporter 2 x 8 kg.
• Ce produit est uniquement destiné à une utilisation en intérieur et ne doit
pas être utilisé à l’extérieur.
Warnhinweise
• Beachten Sie bei der Montage dieses Produkts die Montageanweisungen.
• Überschreiten Sie nicht die Tragkraft dieses Produkts. Ein Überladen dieses
Produkts kann zu Verletzungen oder zur Beschädigung des Produkts führen.
Dieses Produkt ist für folgendes Gewicht geeignet: 2 x 8 kg.
• Dieses Produkt ist nur zum Gebrauch in Innenräumen vorgesehen und sollte
nicht im Freien verwendet werden.
Dichiarazioni di avvertenza
• Assicurarsi di Assemblare il prodotto secondo le istruzioni.
• Non superare la capacità di carico del prodotto. Il sovraccarico del prodotto
potrebbe causare danni o lesioni. Il prodotto è in grado di supportare i
seguenti pesi: 2 x 8 kg.
• Il prodotto è destinato all’uso in ambienti interni. Se ne sconsiglia l’impiego
in ambienti esterni.

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Mensagens de aviso
• Certique-se de que monta este produto de acordo com as instruções.
• Não exceda a capacidade de peso deste produto. Sobrecarregar este produto
pode resultar em ferimentos ou danos de propriedade. Este produto pode
suportar o seguinte peso: 2 x 8 kg.
• Este produto destina-se apenas a uma utilização no interior e não deve ser
utilizado no exterior.
Advertencias de uso
• Asegúrese de ensamblar este producto según las instrucciones.
• Asegúrese de no exceder la capacidad de peso de este producto. La
sobrecarga de este producto puede causar lesiones personales o daños en la
propiedad. Este producto tiene capicidad para el siguiente peso: 2 x 8 kg.
• El uso de este producto es solo para interiores y no debe utilizarse en
exteriores.
Waarschuwingen
• Zorg dat u dit product volgens de instructies in elkaar zet.
• Overschrijd de maximale capaciteit van dit product niet. Overbelasting
van dit product kan letsel of materiële schade veroorzaken. Dit product
ondersteunt het volgende gewicht: 2 x 8 kg.
• Dit product is alleen bedoeld voor binnengebruik en mag niet buiten
worden gebruikt.
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。
• 本製品で定められた最大積載重量を超えないようにして下さい。最大積載重量をオーバーした
場合、怪我をする恐れや器物破損の恐れがあります。 本製品は、モニター1台あたり2x8kgまで
支持できます。
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。

4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Warning Statements..............................................................................2
Product Diagram....................................................................................5
Product Dimensions ..............................................................................6
Product Information..............................................................................7
Package Contents ..................................................................................................................................... 7
Product Specications............................................................................................................................. 11
Requirements ............................................................................................................................................. 12
Mounting the Monitor Arm Using the C-Clamp................................13
Using the Grommet Mount...................................................................17
Attaching the Monitors (Flush)............................................................24
Attaching the Monitors (Recessed).....................................................26
Mounting the Monitors.........................................................................28
Adjusting the Monitors .........................................................................30
Tilt Adjustment .......................................................................................................................................... 30
Micro Adjustments ................................................................................................................................... 31
Routing the Cables.................................................................................33

5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
1Swivel Arm Assembly 5C- Clamp
2VESA Mount x 2 6Grommet
3Pole
4Cable Management Clips
2
1
3
4
56

6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Dimensions

7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
VESA Mounts
Qty: Two
Swivel Arm Assembly
Qty: One
C-Clamp Assembly
Qty: One
Pole
Qty: One

8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Pole Cap
Qty: One
Cable Management Clip
Qty: Two
Grommet Base Plate
Qty: One
Micro-Adjustment Knobs
Qty: Two
Micro-Adjustment Knob
Screws
Qty: Two
Rubber Pads
Qty: Five

9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Pole Assembly Screw
Qty: Three
Grommet Plate
Qty: One
4 mm Hex Key
Qty: One
6 mm Hex Key
Qty: One
M4 x 12 mm Screws
Qty: Eight
M4 x 16 mm Screws
Qty: Eight

10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
M5 x 12 mm Screws
Qty: Eight
M5 x 16 mm Screws
Qty: Eight
Washers
Qty: Eight
Spacers
Qty: Sixteen
Swivel Arm Cable Clip
Qty: Four
3 mm Hex Key
Qty: One

11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Specications
VESA
75 x 75
100 x 100
LB
kg
Total Weight (two monitors)
35.2 lb. (2 x 8 kg)
Screen Size
Max. 32 “
Rotation
360o

12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Tilt
- 450to +450
Swivel
- 900to +900
Requirements
• Phillips Head Screwdriver x 1
• Monitors x 2
• Mounting Surface x 1

13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Mounting the Monitor Arm
Using the C-Clamp
1. Insert the Pole Cap into the top of the Pole.
Installing the Pole Cap
2. Slide the Cable Management Clips onto of the pole.
- or -
Clip the Cable Management Clip onto the Pole.
Installing Cable Management Clip
3. Align the three Screw Holes on the top of the C-Clamp with
the three Screw Holes on the bottom of the Pole.
4. Insert the three Pole Assembly Screws through the Screw
Holes on the top of the C-Clamp and into the Screw Holes
on the bottom of the Pole.

14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. Using the 4 mm Hex Key, tighten the three Pole Assembly
Screws. Being careful not to over-tighten the Pole Assembly
Screws.
6. Remove the backing from the Rubber Pads (x 5).
7. Apply the adhesive side of the Rubber Pads to the under
side of the top of the C-Clamp.
Attaching the C-Clamp to the Pole
8. While supporting the weight of the Monitor Arm, slide the
C-Clamp over the edge of the Mounting Surface.
9. Using your hand, tighten the Knob until the C-Clamp is
pressed tightly against the Mounting Surface.

15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
10. Using the 3 mm Hex Key, loosen the Adjustment Screw on
the Collar.
11. Position the Collar at the height you want the Monitors to
sit.
12. Using the 3 mm Hex Key, tighten the Adjustment Screw on
the side of the Collar, securing the Collar to the Pole.
13. Clip the Arm Assembly Clips (x 4) into place along the
Swivel Arm Assembly.
Installing the Arm Assembly Clips
14. Slide the Swivel Arm Assembly over-top of the Pole, until
the Swivel Arm Assembly comes in contact with the Collar.

16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the Swivel Arm Assembly
15. While holding the weight of the Swivel Arm Assembly, use
the 6 mm Hex Key to tighten the Adjustment Screw on the
Swivel Arm Assembly to secure the Swivel Arm Assembly
in place.

17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Tightening the Swivel Arm
Using the Grommet Mount
1. Insert the Pole Cap into the top of the Pole.
Installing the Pole Cap

18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Slide the Cable Management Clips onto of the pole.
- or -
Clip the Cable Management Clip onto the Pole.
Installing Cable Management Clip
3. Align the three Screw Holes on the top of the C-Clamp with
the three Screw Holes on the bottom of the Pole.
4. Using a Phillips Head Screw Driver, remove the small screw
attached to the Knob onto the C-Clamp.
Removing the Knob
5. Remove the backing from the Rubber Pads (x 5).

19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
6. Apply the adhesive side of the Rubber Pads to the side of
the Grommet Base Plate without the protrusion.
7. Align the Protrusion on the Grommet Base Plate with the
Notch on the bottom of the Pole.
Aligning the Grommet Base Plate
8. Insert the Protrusion on the Grommet Base Plate into the
Notch on the bottom of the Pole.
9. While holding the Grommet Base Plate against the bottom
of the Pole, align the center hole on the Grommet Base
Plate with the Grommet Hole in the Mounting Surface.
10. On the under side of the Mounting Surface, align the
Grommet Plate with the Grommet Hole.
11. Insert the Knob through the Grommet Plate and Grommet
Hole and into the Grommet Base Plate and Pole.